summaryrefslogtreecommitdiff
path: root/include/configs/spear-common.h
blob: b386c7ca706a73fbfb021189ac95a3f6a587d1e4 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
/*
 * (C) Copyright 2009
 * Vipin Kumar, STMicroelectronics, <vipin.kumar@st.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _SPEAR_COMMON_H
#define _SPEAR_COMMON_H
/*
 * Common configurations used for both spear3xx as well as spear6xx
 */

#define CONFIG_SYS_GENERIC_BOARD

/* U-boot Load Address */
#define CONFIG_SYS_TEXT_BASE			0x00700000

/* Ethernet driver configuration */
#define CONFIG_MII
#define CONFIG_PHYLIB
#define CONFIG_PHY_RESET_DELAY			10000		/* in usec */
#define CONFIG_PHY_GIGE			/* Include GbE speed/duplex detection */

/* USBD driver configuration */
#if defined(CONFIG_SPEAR_USBTTY)
#define CONFIG_DW_UDC
#define CONFIG_USB_DEVICE
#define CONFIG_USBD_HS
#define CONFIG_USB_TTY

#define CONFIG_USBD_PRODUCT_NAME		"SPEAr SoC"
#define CONFIG_USBD_MANUFACTURER		"ST Microelectronics"

#endif

#define CONFIG_EXTRA_ENV_USBTTY			"usbtty=cdc_acm\0"

/* I2C driver configuration */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_DW
#if defined(CONFIG_SPEAR600)
#define CONFIG_SYS_I2C_BASE			0xD0200000
#elif defined(CONFIG_SPEAR300)
#define CONFIG_SYS_I2C_BASE			0xD0180000
#elif defined(CONFIG_SPEAR310)
#define CONFIG_SYS_I2C_BASE			0xD0180000
#elif defined(CONFIG_SPEAR320)
#define CONFIG_SYS_I2C_BASE			0xD0180000
#endif
#define CONFIG_SYS_I2C_SPEED			400000
#define CONFIG_SYS_I2C_SLAVE			0x02

#define CONFIG_I2C_CHIPADDRESS			0x50

/* Timer, HZ specific defines */

/* Flash configuration */
#if defined(CONFIG_FLASH_PNOR)
#define CONFIG_SPEAR_EMI
#else
#define CONFIG_ST_SMI
#endif

#if defined(CONFIG_ST_SMI)

#define CONFIG_SYS_MAX_FLASH_BANKS		2
#define CONFIG_SYS_FLASH_BASE			0xF8000000
#define CONFIG_SYS_CS1_FLASH_BASE		0xF9000000
#define CONFIG_SYS_FLASH_BANK_SIZE		0x01000000
#define CONFIG_SYS_FLASH_ADDR_BASE		{CONFIG_SYS_FLASH_BASE, \
						CONFIG_SYS_CS1_FLASH_BASE}
#define CONFIG_SYS_MAX_FLASH_SECT		128

#define CONFIG_SYS_FLASH_ERASE_TOUT		(3 * CONFIG_SYS_HZ)
#define CONFIG_SYS_FLASH_WRITE_TOUT		(3 * CONFIG_SYS_HZ)

#endif

/*
 * Serial Configuration (PL011)
 * CONFIG_PL01x_PORTS is defined in specific files
 */
#define CONFIG_PL011_SERIAL
#define CONFIG_PL011_CLOCK			(48 * 1000 * 1000)
#define CONFIG_CONS_INDEX			0
#define CONFIG_BAUDRATE				115200
#define CONFIG_SYS_BAUDRATE_TABLE		{ 9600, 19200, 38400, \
						57600, 115200 }

#define CONFIG_SYS_LOADS_BAUD_CHANGE

/* NAND FLASH Configuration */
#define CONFIG_SYS_NAND_SELF_INIT
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_NAND_FSMC
#define CONFIG_SYS_MAX_NAND_DEVICE		1
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_QUIET_TEST

/*
 * Command support defines
 */
#define CONFIG_CMD_I2C
#define CONFIG_CMD_NAND
#define CONFIG_CMD_ENV
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_RUN
#define CONFIG_CMD_SAVES
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP

/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <config_cmd_default.h>

/*
 * Default Environment Varible definitions
 */
#if defined(CONFIG_SPEAR_USBTTY)
#define CONFIG_BOOTDELAY			-1
#else
#define CONFIG_BOOTDELAY			1
#endif

#define CONFIG_ENV_OVERWRITE

/*
 * U-Boot Environment placing definitions.
 */
#if defined(CONFIG_ENV_IS_IN_FLASH)
#ifdef CONFIG_ST_SMI
/*
 * Environment is in serial NOR flash
 */
#define CONFIG_SYS_MONITOR_LEN			0x00040000
#define CONFIG_ENV_SECT_SIZE			0x00010000
#define CONFIG_FSMTDBLK				"/dev/mtdblock3 "

#define CONFIG_BOOTCOMMAND			"bootm 0xf8050000"

#elif defined(CONFIG_SPEAR_EMI)
/*
 * Environment is in parallel NOR flash
 */
#define CONFIG_SYS_MONITOR_LEN			0x00060000
#define CONFIG_ENV_SECT_SIZE			0x00020000
#define CONFIG_FSMTDBLK				"/dev/mtdblock3 "

#define CONFIG_BOOTCOMMAND			"cp.b 0x50080000 0x1600000 " \
						"0x4C0000; bootm 0x1600000"
#endif

#define CONFIG_ENV_ADDR				(CONFIG_SYS_FLASH_BASE + \
						CONFIG_SYS_MONITOR_LEN)
#elif defined(CONFIG_ENV_IS_IN_NAND)
/*
 * Environment is in NAND
 */

#define CONFIG_ENV_OFFSET			0x60000
#define CONFIG_ENV_RANGE			0x10000
#define CONFIG_FSMTDBLK				"/dev/mtdblock7 "

#define CONFIG_BOOTCOMMAND			"nand read.jffs2 0x1600000 " \
						"0x80000 0x4C0000; " \
						"bootm 0x1600000"
#endif

#define CONFIG_BOOTARGS				"console=ttyAMA0,115200 " \
						"mem=128M " \
						"root="CONFIG_FSMTDBLK \
						"rootfstype=jffs2"

#define CONFIG_NFSBOOTCOMMAND						\
	"bootp; "							\
	"setenv bootargs root=/dev/nfs rw "				\
	"nfsroot=$(serverip):$(rootpath) "				\
	"ip=$(ipaddr):$(serverip):$(gatewayip):"			\
			"$(netmask):$(hostname):$(netdev):off "		\
			"console=ttyAMA0,115200 $(othbootargs);"	\
	"bootm; "

#define CONFIG_RAMBOOTCOMMAND						\
	"setenv bootargs root=/dev/ram rw "				\
		"console=ttyAMA0,115200 $(othbootargs);"		\
	CONFIG_BOOTCOMMAND


#define CONFIG_ENV_SIZE				0x02000
#define CONFIG_SYS_MONITOR_BASE			CONFIG_SYS_TEXT_BASE

/* Miscellaneous configurable options */
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_BOOT_PARAMS_ADDR			0x00000100
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_MISC_INIT_R
#define CONFIG_ZERO_BOOTDELAY_CHECK

#define CONFIG_SYS_MEMTEST_START		0x00800000
#define CONFIG_SYS_MEMTEST_END			0x04000000
#define CONFIG_SYS_MALLOC_LEN			(1024*1024)
#define CONFIG_IDENT_STRING			"-SPEAr"
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_PROMPT			"u-boot> "
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_CBSIZE			256
#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + \
						sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS			16
#define CONFIG_SYS_BARGSIZE			CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LOAD_ADDR			0x00800000
#define CONFIG_SYS_CONSOLE_INFO_QUIET

#define CONFIG_SYS_FLASH_EMPTY_INFO

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS			1
#define PHYS_SDRAM_1				0x00000000
#define PHYS_SDRAM_1_MAXSIZE			0x40000000

#define CONFIG_SYS_SDRAM_BASE			PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR		0xD2800000
#define CONFIG_SYS_INIT_RAM_SIZE		0x2000

#define CONFIG_SYS_INIT_SP_OFFSET		\
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

#define CONFIG_SYS_INIT_SP_ADDR			\
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#endif