1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
|
/*
* Copyright (C) 2008 Embedded Alley Solutions, Inc.
*
* (C) Copyright 2009-2010 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/sizes.h>
/*
* Define this to make U-Boot skip low level initialization when loaded
* by initial bootloader. Not required by NAND U-Boot version but IS
* required for a NOR version used to burn the real NOR U-Boot into
* NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
* so it is NOT possible to build a U-Boot with both NAND and NOR routines.
* NOR U-Boot is loaded directly from Flash so it must perform all the
* low level initialization itself. NAND version is loaded by an initial
* bootloader (UBL in TI-ese) that performs such an initialization so it's
* skipped in NAND version. The third DaVinci boot mode loads a bootloader
* via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
* performing low level init prior to loading. All that means we can NOT use
* NAND version to put U-Boot into NOR because it doesn't have NOR support and
* we can NOT use NOR version because it performs low level initialization
* effectively destroying itself in DDR memory. That's why a separate NOR
* version with this define is needed. It is loaded via UART, then one uses
* it to somehow download a proper NOR version built WITHOUT this define to
* RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
* NOR support into the initial bootloader so it won't be needed but DaVinci
* static RAM might be too small for this (I have something like 2Kbytes left
* as of now, without NOR support) so this might've not happened...
*
*/
/*===================*/
/* SoC Configuration */
/*===================*/
#define CONFIG_ARM926EJS /* arm926ejs CPU core */
#define CONFIG_MX23 /* MX23 SoC */
#define CONFIG_MX23_EVK /* MX23 EVK board */
#define CONFIG_SYS_CLK_FREQ 120000000 /* Arm Clock frequency */
#define CONFIG_USE_TIMER0 /* use timer 0 */
#define CONFIG_SYS_HZ 1000 /* Ticks per second */
/*=============*/
/* Memory Info */
/*=============*/
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */
#define CONFIG_SYS_MEMTEST_START 0x40000000 /* memtest start address */
#define CONFIG_SYS_MEMTEST_END 0x41000000 /* 16MB RAM test */
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define CONFIG_STACKSIZE (256*1024) /* regular stack */
#define PHYS_SDRAM_1 0x40000000 /* mDDR Start */
#define PHYS_SDRAM_1_SIZE 0x02000000 /* mDDR size 32MB */
/*====================*/
/* Serial Driver info */
/*====================*/
#define CONFIG_STMP3XXX_DBGUART /* 378x debug UART */
#define CONFIG_DBGUART_CLK 24000000
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*====================*/
/* SPI Driver info */
/*====================*/
#define CONFIG_SSP_CLK 48000000
#define CONFIG_SPI_CLK 3000000
#define CONFIG_SPI_SSP1
#undef CONFIG_SPI_SSP2
/*=====================*/
/* Flash & Environment */
/*=====================*/
#define CONFIG_SYS_NO_FLASH /* Flash is not supported */
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_SIZE 0x20000
/*==============================*/
/* U-Boot general configuration */
/*==============================*/
#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */
#define CONFIG_MISC_INIT_R
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_IPADDR 192.167.10.2
#define CONFIG_SERVERIP 192.167.10.1
#define CONFIG_BOOTDELAY 2
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_PROMPT "MX23 U-Boot > "
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
/* Print buffer sz */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* Boot Argument Buffer Size */
#define CONFIG_SYS_LOAD_ADDR 0x40400000
/* default Linux kernel load address */
#define CONFIG_VERSION_VARIABLE
#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
#define CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#define CONFIG_CMDLINE_EDITING
#define CFG_LONGHELP
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/*===================*/
/* Linux Information */
/*===================*/
#define LINUX_BOOT_PARAM_ADDR 0x40000100
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTARGS "console=ttyAM0,115200n8 "\
"root=/dev/mtdblock1 rootfstype=jffs2 lcd_panel=lms350"
#define CONFIG_BOOTCOMMAND "tftpboot ; bootm"
/*=================*/
/* U-Boot commands */
/*=================*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_DNS
#undef CONFIG_CMD_DIAG
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_NET
#define CONFIG_CMD_SAVES
#undef CONFIG_CMD_IMLS
/* Ethernet chip - select an alternative driver */
#define CONFIG_ENC28J60_ETH
#define CONFIG_ENC28J60_ETH_SPI_BUS 0
#define CONFIG_ENC28J60_ETH_SPI_CS 0
#endif /* __CONFIG_H */
|
