summaryrefslogtreecommitdiff
path: root/include/configs/EXBITGEN.h
blob: 502e7471a70c31fb72d50ed4e1f8cc84d6e51a6b (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
/*
 * (C) Copyright 2000-2004
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405GP		1	/* This is a PPC405GP CPU	*/
#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
#define CONFIG_EXBITGEN		1	/* on a Exbit Generic board     */

#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/

#define CONFIG_SYS_CLK_FREQ     25000000 /* external frequency to pll   */

/* I2C configuration */
#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
#define CONFIG_SYS_I2C_SPEED		40000	/* I2C speed			*/
#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address		*/

/* environment is in EEPROM */
#define CONFIG_ENV_IS_IN_EEPROM    1
#undef CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_ENV_IS_IN_NVRAM

#ifdef CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x56    /* 1010110 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1	/* 8-bit internal addressing */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	1	/* ... and 1 bit in I2C address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3	/* 4 bytes per page */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	40	/* write takes up to 40 msec */
#define CONFIG_ENV_OFFSET		4	/* Offset of Environment Sector	*/
#define	CONFIG_ENV_SIZE		350	/* that is 350 bytes only!	*/
#endif

#define CONFIG_BOOTDELAY	10	/* autoboot after 10 seconds	*/
/* Explanation:
   autbooting is altogether disabled and cannot be
   enabled if CONFIG_BOOTDELAY is negative.
   If you want shorter bootdelay, then
   - "setenv bootdelay <delay>" to the proper value
*/

#define CONFIG_BOOTCOMMAND	"bootm 20400000 20800000"

#define CONFIG_BOOTARGS		"root=/dev/ram "  \
				"ramdisk_size=32768 " \
				"console=ttyS0,115200 " \
				"ram=128M debug"

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

#define CONFIG_MII		1	/* MII PHY management		*/
#define CONFIG_PHY_ADDR		0	/* PHY address			*/


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_PPC4xx_EMAC
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>


#undef CONFIG_WATCHDOG			/* watchdog disabled		*/

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#if defined(CONFIG_CMD_KGDB)
#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

/* UART configuration */
#define CONFIG_SYS_BASE_BAUD		691200

/* Default baud rate */
#define CONFIG_BAUDRATE		115200

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE      \
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
	 57600, 115200, 230400, 460800, 921600 }

#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */

#define	CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks	*/

/*-----------------------------------------------------------------------
 * PCI stuff
 *-----------------------------------------------------------------------
 */
#undef CONFIG_PCI			/* no pci support	        */

/*-----------------------------------------------------------------------
 * External peripheral base address
 *-----------------------------------------------------------------------
 */
#undef  CONFIG_IDE_PCMCIA               /* no pcmcia interface required */
#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
#undef  CONFIG_IDE_RESET                /* no reset for ide supported   */

#define	CONFIG_SYS_KEY_REG_BASE_ADDR	0xF0100000
#define	CONFIG_SYS_IR_REG_BASE_ADDR	0xF0200000
#define	CONFIG_SYS_FPGA_REG_BASE_ADDR	0xF0300000

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH0_BASE		0xFFF80000
#define CONFIG_SYS_FLASH0_SIZE		0x00080000
#define CONFIG_SYS_FLASH1_BASE		0x20000000
#define CONFIG_SYS_FLASH1_SIZE		0x02000000
#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH0_BASE
#define CONFIG_SYS_FLASH_SIZE		CONFIG_SYS_FLASH0_SIZE
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 196 kB for Monitor	*/
#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/

#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH0_BASE
#define CONFIG_SYS_RAMSTART
#endif

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CONFIG_SYS_MAX_FLASH_BANKS	5	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OFFSET		0x00060000 /* Offset of Environment Sector      */
#define	CONFIG_ENV_SIZE		0x00010000 /* Total Size of Environment Sector	*/
#define CONFIG_ENV_SECT_SIZE	0x00010000 /* see README - env sector total size */
#endif

/* On Chip Memory location/size */
#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x1000

/* Global info and initial stack */
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM	*/
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif
#endif	/* __CONFIG_H */