1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
|
STMicroelectronics STM32MP1 clock tree initialization
=====================================================
The STM32MP clock tree initialization is based on device tree information
for RCC IP and on fixed clocks.
-------------------------------
RCC CLOCK = st,stm32mp1-rcc-clk
-------------------------------
The RCC IP is both a reset and a clock controller but this documentation only
describes the fields added for clock tree initialization which are not present
in Linux binding.
Please refer to ../mfd/st,stm32-rcc.txt for all the other properties common
with Linux.
Required properties:
- compatible: Should be "st,stm32mp1-rcc-clk"
- st,clksrc : The clock source in this order
for STM32MP15x: 9 clock sources are requested
MPU AXI MCU PLL12 PLL3 PLL4 RTC MCO1 MCO2
with value equals to RCC clock specifier as defined in
dt-bindings/clock/stm32mp1-clksrc.h: CLK_<NAME>_<SOURCE>
- st,clkdiv : The div parameters in this order
for STM32MP15x: 11 dividers value are requested
MPU AXI MCU APB1 APB2 APB3 APB4 APB5 RTC MCO1 MCO2
with DIV coding defined in RCC associated register RCC_xxxDIVR
most the case, it is:
0x0: not divided
0x1: division by 2
0x2: division by 4
0x3: division by 8
...
but for RTC MCO1 MCO2, the coding is different:
0x0: not divided
0x1: division by 2
0x2: division by 3
0x3: division by 4
...
Optional Properties:
- st,pll
PLL children node for PLL1 to PLL4 : (see ref manual for details)
with associated index 0 to 3 (st,pll@0 to st,pll@4)
PLLx is off when the associated node is absent
- Sub-nodes:
- cfg: The parameters for PLL configuration in this order:
DIVM DIVN DIVP DIVQ DIVR Output
with DIV value as defined in RCC spec:
0x0: bypass (division by 1)
0x1: division by 2
0x2: division by 3
0x3: division by 4
...
and Output = bitfield for each output value = 1:ON/0:OFF
BIT(0) => output P : DIVPEN
BIT(1) => output Q : DIVQEN
BIT(2) => output R : DIVREN
NB : macro PQR(p,q,r) can be used to build this value
with p,p,r = 0 or 1
- frac : Fractional part of the multiplication factor
(optional, PLL is in integer mode when absent)
- csg : Clock Spreading Generator (optional)
with parameters in this order:
MOD_PER INC_STEP SSCG_MODE
* MOD_PER: Modulation Period Adjustment
* INC_STEP: Modulation Depth Adjustment
* SSCG_MODE: Spread spectrum clock generator mode
you can use associated defines from stm32mp1-clksrc.h
* SSCG_MODE_CENTER_SPREAD = 0
* SSCG_MODE_DOWN_SPREAD = 1
- st,pkcs : used to configure the peripherals kernel clock selection
containing a list of peripheral kernel clock source identifier as defined
in the file dt-bindings/clock/stm32mp1-clksrc.h
Example:
rcc: rcc@50000000 {
compatible = "syscon", "simple-mfd";
reg = <0x50000000 0x1000>;
rcc_clk: rcc-clk@50000000 {
#clock-cells = <1>;
compatible = "st,stm32mp1-rcc-clk";
st,clksrc = < CLK_MPU_PLL1P
CLK_AXI_PLL2P
CLK_MCU_HSI
CLK_PLL12_HSE
CLK_PLL3_HSE
CLK_PLL4_HSE
CLK_RTC_HSE
CLK_MCO1_DISABLED
CLK_MCO2_DISABLED
>;
st,clkdiv = <
1 /*MPU*/
0 /*AXI*/
0 /*MCU*/
1 /*APB1*/
1 /*APB2*/
1 /*APB3*/
1 /*APB4*/
5 /*APB5*/
23 /*RTC*/
0 /*MCO1*/
0 /*MCO2*/
>;
st,pll@0 {
cfg = < 1 53 0 0 0 1 >;
frac = < 0x810 >;
};
st,pll@1 {
cfg = < 1 43 1 0 0 PQR(0,1,1)>;
csg = <10 20 1>;
};
st,pll@2 {
cfg = < 2 85 3 13 3 0>;
csg = <10 20 SSCG_MODE_CENTER_SPREAD>;
};
st,pll@3 {
cfg = < 2 78 4 7 9 3>;
};
st,pkcs = <
CLK_STGEN_HSE
CLK_CKPER_HSI
CLK_USBPHY_PLL2P
CLK_DSI_PLL2Q
>;
};
};
--------------------------
other clocks = fixed-clock
--------------------------
The clock tree is also based on 5 fixed-clock in clocks node
used to define the state of associated ST32MP1 oscillators:
- clk-lsi
- clk-lse
- clk-hsi
- clk-hse
- clk-csi
At boot the clock tree initialization will
- enable the oscillator present in device tree
- disable HSI oscillator if the node is absent (always activated by bootrom)
Optional properties :
a) for external oscillator: "clk-lse", "clk-hse"
4 optional fields are managed
- "st,bypass" Configure the oscillator bypass mode (HSEBYP, LSEBYP)
- "st,digbypass" Configure the bypass mode as full-swing digital signal
(DIGBYP)
- "st,css" Activate the clock security system (HSECSSON, LSECSSON)
- "st,drive" (only for LSE) value of the drive for the oscillator
(see LSEDRV_ define in the file dt-bindings/clock/stm32mp1-clksrc.h)
Example board file:
/ {
clocks {
clk_hse: clk-hse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <64000000>;
st,bypass;
};
clk_lse: clk-lse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
st,css;
st,drive = <LSEDRV_LOWEST>;
};
};
b) for internal oscillator: "clk-hsi"
internally HSI clock is fixed to 64MHz for STM32MP157 soc
in device tree clk-hsi is the clock after HSIDIV (ck_hsi in RCC doc)
So this clock frequency is used to compute the expected HSI_DIV
for the clock tree initialisation
ex: for HSIDIV = /1
/ {
clocks {
clk_hsi: clk-hsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <64000000>;
};
};
ex: for HSIDIV = /2
/ {
clocks {
clk_hsi: clk-hsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32000000>;
};
};
|
