summaryrefslogtreecommitdiff
path: root/board/zyxel/nsa310s/nsa310s.c
blob: e7cb6be616f858906d86db0bfff0a6926bedfb73 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2015
 * Gerald Kerma <dreagle@doukki.net>
 * Tony Dinh <mibodhi@gmail.com>
 */

#include <common.h>
#include <miiphy.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <asm/arch/mpp.h>
#include <asm/io.h>
#include "nsa310s.h"

DECLARE_GLOBAL_DATA_PTR;

int board_early_init_f(void)
{
	/*
	 * default gpio configuration
	 * There are maximum 64 gpios controlled through 2 sets of registers
	 * the below configuration configures mainly initial LED status
	 */
	mvebu_config_gpio(NSA310S_VAL_LOW, NSA310S_VAL_HIGH,
			  NSA310S_OE_LOW, NSA310S_OE_HIGH);

	/* (all LEDs & power off active high) */
	/* Multi-Purpose Pins Functionality configuration */
	static const u32 kwmpp_config[] = {
		MPP0_NF_IO2,
		MPP1_NF_IO3,
		MPP2_NF_IO4,
		MPP3_NF_IO5,
		MPP4_NF_IO6,
		MPP5_NF_IO7,
		MPP6_SYSRST_OUTn,
		MPP7_GPO,
		MPP8_TW_SDA,
		MPP9_TW_SCK,
		MPP10_UART0_TXD,
		MPP11_UART0_RXD,
		MPP12_GPO,
		MPP13_GPIO,
		MPP14_GPIO,
		MPP15_GPIO,
		MPP16_GPIO,
		MPP17_GPIO,
		MPP18_NF_IO0,
		MPP19_NF_IO1,
		MPP20_GPIO,
		MPP21_GPIO,
		MPP22_GPIO,
		MPP23_GPIO,
		MPP24_GPIO,
		MPP25_GPIO,
		MPP26_GPIO,
		MPP27_GPIO,
		MPP28_GPIO,
		MPP29_GPIO,
		MPP30_GPIO,
		MPP31_GPIO,
		MPP32_GPIO,
		MPP33_GPIO,
		MPP34_GPIO,
		MPP35_GPIO,
		0
	};
	kirkwood_mpp_conf(kwmpp_config, NULL);
	return 0;
}

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;

	return 0;
}

#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
	u16 reg;
	u16 phyaddr;
	char *name = "egiga0";

	if (miiphy_set_current_dev(name))
		return;

	/* read PHY dev address */
	if (miiphy_read(name, 0xee, 0xee, (u16 *) &phyaddr)) {
		printf("could not read PHY dev address\n");
		return;
	}

	/* set RGMII delay */
	miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
	miiphy_read(name, phyaddr, MV88E1318_MAC_CTRL_REG, &reg);
	reg |= (MV88E1318_RGMII_RX_CTRL | MV88E1318_RGMII_TX_CTRL);
	miiphy_write(name, phyaddr, MV88E1318_MAC_CTRL_REG, reg);
	miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, 0);

	/* reset PHY */
	if (miiphy_reset(name, phyaddr))
		return;

	/*
	 * ZyXEL NSA310S uses the 88E1310S Alaska (interface identical to 88E1318)
	 * and has an MCU attached to the LED[2] via tristate interrupt
	 */

	/* switch to LED register page */
	miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
	/* read out LED polarity register */
	miiphy_read(name, phyaddr, MV88E1318_LED_POL_REG, &reg);
	/* clear 4, set 5 - LED2 low, tri-state */
	reg &= ~(MV88E1318_LED2_4);
	reg |= (MV88E1318_LED2_5);
	/* write back LED polarity register */
	miiphy_write(name, phyaddr, MV88E1318_LED_POL_REG, reg);
	/* jump back to page 0, per the PHY chip documenation. */
	miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, 0);

	/* set PHY back to auto-negotiation mode */
	miiphy_write(name, phyaddr, 0x4, 0x1e1);
	miiphy_write(name, phyaddr, 0x9, 0x300);
	/* downshift */
	miiphy_write(name, phyaddr, 0x10, 0x3860);
	miiphy_write(name, phyaddr, 0x0, 0x9140);
}
#endif /* CONFIG_RESET_PHY_R */