summaryrefslogtreecommitdiff
path: root/board/xes/xpedite550x/ddr.c
blob: 3b6e08bfcdd1449454eb76cf8c2428e2d717ea11 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
/*
 * Copyright 2010 Extreme Engineering Solutions, Inc.
 * Copyright 2007-2008 Freescale Semiconductor, Inc.
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <common.h>
#include <i2c.h>

#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>

void get_spd(ddr3_spd_eeprom_t *spd, u8 i2c_address)
{
	i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
		 sizeof(ddr3_spd_eeprom_t));
}

/*
 *     There are traditionally three board-specific SDRAM timing parameters
 *     which must be calculated based on the particular PCB artwork.  These are:
 *     1.) CPO (Read Capture Delay)
 *	       - TIMING_CFG_2 register
 *	       Source: Calculation based on board trace lengths and
 *		       chip-specific internal delays.
 *     2.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
 *	       - DDR_SDRAM_CLK_CNTL register
 *	       Source: Signal Integrity Simulations
 *     3.) 2T Timing on Addr/Ctl
 *	       - TIMING_CFG_2 register
 *	       Source: Signal Integrity Simulations
 *	       Usually only needed with heavy load/very high speed (>DDR2-800)
 *
 *     ====== XPedite550x DDR3-800 read delay calculations ======
 *
 *     The P2020 processor provides an autoleveling option. Setting CPO to
 *     0x1f enables this auto configuration.
 */

typedef struct {
	unsigned short datarate_mhz_low;
	unsigned short datarate_mhz_high;
	unsigned char clk_adjust;
	unsigned char cpo;
} board_specific_parameters_t;

const board_specific_parameters_t board_specific_parameters[][20] = {
	{
		/* Controller 0 */
		{
			/* DDR3-600/667 */
			.datarate_mhz_low	= 500,
			.datarate_mhz_high	= 750,
			.clk_adjust		= 5,
			.cpo			= 31,
		},
		{
			/* DDR3-800 */
			.datarate_mhz_low	= 750,
			.datarate_mhz_high	= 850,
			.clk_adjust		= 5,
			.cpo			= 31,
		},
	},
};

void fsl_ddr_board_options(memctl_options_t *popts,
				dimm_params_t *pdimm,
				unsigned int ctrl_num)
{
	const board_specific_parameters_t *pbsp =
				&(board_specific_parameters[ctrl_num][0]);
	u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
				sizeof(board_specific_parameters[0][0]);
	u32 i;
	ulong ddr_freq;

	/*
	 * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
	 * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
	 * there are two dimms in the controller, set odt_rd_cfg to 3 and
	 * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
	 */
	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
		if (i&1) {	/* odd CS */
			popts->cs_local_opts[i].odt_rd_cfg = 0;
			popts->cs_local_opts[i].odt_wr_cfg = 0;
		} else {	/* even CS */
			if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
				popts->cs_local_opts[i].odt_rd_cfg = 0;
				popts->cs_local_opts[i].odt_wr_cfg = 4;
			} else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
				popts->cs_local_opts[i].odt_rd_cfg = 3;
				popts->cs_local_opts[i].odt_wr_cfg = 3;
			}
		}
	}

	/*
	 * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
	 * freqency and n_banks specified in board_specific_parameters table.
	 */
	ddr_freq = get_ddr_freq(0) / 1000000;

	for (i = 0; i < num_params; i++) {
		if (ddr_freq >= pbsp->datarate_mhz_low &&
		    ddr_freq <= pbsp->datarate_mhz_high) {
			popts->clk_adjust = pbsp->clk_adjust;
			popts->cpo_override = pbsp->cpo;
			popts->twoT_en = 0;
		}
		pbsp++;
	}

	/*
	 * Factors to consider for half-strength driver enable:
	 *	- number of DIMMs installed
	 */
	popts->half_strength_driver_enable = 0;

	/*
	 * Enable on-die termination.
	 * From the Micron Technical Node TN-41-04, RTT_Nom should typically
	 * be 30 to 40 ohms, while RTT_WR should be 120 ohms.  Setting RTT_WR
	 * is handled in the Freescale DDR3 driver.  Set RTT_Nom here.
	 */
	popts->rtt_override = 1;
	popts->rtt_override_value = 3;
}