summaryrefslogtreecommitdiff
path: root/board/xes/xpedite537x/ddr.c
blob: 56b5a187d827f85b4251f13d4e776ee21d2207e7 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
/*
 * Copyright 2008 Extreme Engineering Solutions, Inc.
 * Copyright 2008 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <i2c.h>

#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>

void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
{
	i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
		 sizeof(ddr2_spd_eeprom_t));
}

/*
 * There are four board-specific SDRAM timing parameters which must be
 * calculated based on the particular PCB artwork.  These are:
 *   1.) CPO (Read Capture Delay)
 *           - TIMING_CFG_2 register
 *           Source: Calculation based on board trace lengths and
 *                   chip-specific internal delays.
 *   2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
 *           - TIMING_CFG_2 register
 *           Source: Calculation based on board trace lengths.
 *                   Unless clock and DQ lanes are very different
 *                   lengths (>2"), this should be set to the nominal value
 *                   of 1/2 clock delay.
 *   3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
 *           - DDR_SDRAM_CLK_CNTL register
 *           Source: Signal Integrity Simulations
 *   4.) 2T Timing on Addr/Ctl
 *           - TIMING_CFG_2 register
 *           Source: Signal Integrity Simulations
 *           Usually only needed with heavy load/very high speed (>DDR2-800)
 *
 *     ====== XPedite5370 DDR2-600 read delay calculations ======
 *
 *     See Freescale's App Note AN2583 as refrence.  This document also
 *     contains the chip-specific delays for 8548E, 8572, etc.
 *
 *     For MPC8572E
 *     Minimum chip delay (Ch 0): 1.372ns
 *     Maximum chip delay (Ch 0): 2.914ns
 *     Minimum chip delay (Ch 1): 1.220ns
 *     Maximum chip delay (Ch 1): 2.595ns
 *
 *     CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps
 *
 *     Minimum delay calc (Ch 0):
 *     clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
 *     2.3" * 180 - 400ps     + 1.9" * 180         + 2080ps     + 1372ps
 *                                                 = 3808ps
 *                                                 = 3.808ns
 *
 *     Maximum delay calc (Ch 0):
 *     clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
 *     2.3" * 180 + 400ps     + 2.4" * 180         + 2080ps     + 2914ps
 *                                                 = 6240ps
 *                                                 = 6.240ns
 *
 *     Minimum delay calc (Ch 1):
 *     clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
 *     1.46" * 180- 400ps     + 0.7" * 180         + 2080ps     + 1220ps
 *                                                 = 3288ps
 *                                                 = 3.288ns
 *
 *     Maximum delay calc (Ch 1):
 *     clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
 *     1.46" * 180+ 400ps     + 1.1" * 180         + 2080ps     + 2595ps
 *                                                 = 5536ps
 *                                                 = 5.536ns
 *
 *     Ch.0: 3.808ns to 6.240ns additional delay needed  (pick 5ns as target)
 *              This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
 *     Ch.1: 3.288ns to 5.536ns additional delay needed  (pick 4.4ns as target)
 *              This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7)
 *
 *
 *     ====== XPedite5370 DDR2-800 read delay calculations ======
 *
 *     See Freescale's App Note AN2583 as refrence.  This document also
 *     contains the chip-specific delays for 8548E, 8572, etc.
 *
 *     For MPC8572E
 *     Minimum chip delay (Ch 0): 1.372ns
 *     Maximum chip delay (Ch 0): 2.914ns
 *     Minimum chip delay (Ch 1): 1.220ns
 *     Maximum chip delay (Ch 1): 2.595ns
 *
 *     CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps
 *
 *     Minimum delay calc (Ch 0):
 *     clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
 *     2.3" * 180 - 350ps     + 1.9" * 180         + 1563ps     + 1372ps
 *                                                 = 3341ps
 *                                                 = 3.341ns
 *
 *     Maximum delay calc (Ch 0):
 *     clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
 *     2.3" * 180 + 350ps     + 2.4" * 180         + 1563ps     + 2914ps
 *                                                 = 5673ps
 *                                                 = 5.673ns
 *
 *     Minimum delay calc (Ch 1):
 *     clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
 *     1.46" * 180- 350ps     + 0.7" * 180         + 1563ps     + 1220ps
 *                                                 = 2822ps
 *                                                 = 2.822ns
 *
 *     Maximum delay calc (Ch 1):
 *     clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
 *     1.46" * 180+ 350ps     + 1.1" * 180         + 1563ps     + 2595ps
 *                                                 = 4968ps
 *                                                 = 4.968ns
 *
 *     Ch.0: 3.341ns to 5.673ns additional delay needed  (pick 4.5ns as target)
 *              This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9)
 *     Ch.1: 2.822ns to 4.968ns additional delay needed  (pick 3.9ns as target)
 *              This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
 *
 * Write latency (WR_DATA_DELAY) is calculated by doing the following:
 *
 *      The DDR SDRAM specification requires DQS be received no sooner than
 *      75% of an SDRAM clock period—and no later than 125% of a clock
 *      period—from the capturing clock edge of the command/address at the
 *      SDRAM.
 *
 * Based on the above tracelengths, the following are calculated:
 *      Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 =  0.342ns
 *      Ch. 0 8572 to DRAM propagation (CLKs) :     2.3" * 180 =  0.414ns
 *      Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 =  0.126ns
 *      Ch. 1 8572 to DRAM propagation (CLKs   ) : 1.47" * 180 =  0.264ns
 *
 * Difference in arrival time CLK vs. DQS:
 *      Ch. 0 0.072ns
 *      Ch. 1 0.138ns
 *
 *      Both of these values are much less than 25% of the clock
 *      period at DDR2-600 or DDR2-800, so no additional delay is needed over
 *      the 1/2 cycle which normally aligns the first DQS transition
 *      exactly WL (CAS latency minus one cycle) after the CAS strobe.
 *      See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's
 *      terminology corresponds to exactly one clock period delay after
 *      the CAS strobe. (due to the fact that the "delay" is referenced
 *      from the *falling* edge of the CLK, just after the rising edge
 *      which the CAS strobe is latched on.
 */

typedef struct board_memctl_options {
	uint16_t datarate_mhz_low;
	uint16_t datarate_mhz_high;
	uint8_t clk_adjust;
	uint8_t cpo_override;
	uint8_t write_data_delay;
} board_memctl_options_t;

static struct board_memctl_options bopts_ctrl[][2] = {
	{
		/* Controller 0 */
		{
			/* DDR2 600/667 */
			.datarate_mhz_low	= 500,
			.datarate_mhz_high	= 750,
			.clk_adjust		= 5,
			.cpo_override		= 8,
			.write_data_delay	= 2,
		},
		{
			/* DDR2 800 */
			.datarate_mhz_low	= 750,
			.datarate_mhz_high	= 850,
			.clk_adjust		= 5,
			.cpo_override		= 9,
			.write_data_delay	= 2,
		},
	},
	{
		/* Controller 1 */
		{
			/* DDR2 600/667 */
			.datarate_mhz_low	= 500,
			.datarate_mhz_high	= 750,
			.clk_adjust		= 5,
			.cpo_override		= 7,
			.write_data_delay	= 2,
		},
		{
			/* DDR2 800 */
			.datarate_mhz_low	= 750,
			.datarate_mhz_high	= 850,
			.clk_adjust		= 5,
			.cpo_override		= 8,
			.write_data_delay	= 2,
		},
	},
};

void fsl_ddr_board_options(memctl_options_t *popts,
			   dimm_params_t *pdimm,
			   unsigned int ctrl_num)
{
	struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
	sys_info_t sysinfo;
	int i;
	unsigned int datarate;

	get_sys_info(&sysinfo);
	datarate = sysinfo.freq_ddrbus / 1000 / 1000;

	for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
		if ((bopts[i].datarate_mhz_low <= datarate) &&
		    (bopts[i].datarate_mhz_high >= datarate)) {
			debug("controller %d:\n", ctrl_num);
			debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
			debug(" cpo = %d\n", bopts[i].cpo_override);
			debug(" write_data_delay = %d\n",
			      bopts[i].write_data_delay);
			popts->clk_adjust = bopts[i].clk_adjust;
			popts->cpo_override = bopts[i].cpo_override;
			popts->write_data_delay = bopts[i].write_data_delay;
		}
	}

	/*
	 * Factors to consider for half-strength driver enable:
	 *	- number of DIMMs installed
	 */
	popts->half_strength_driver_enable = 0;
}