summaryrefslogtreecommitdiff
path: root/board/freescale/t1040qds/ddr.c
blob: a5d3e54cfe810d6f2f89ac5a7358ae4b658f9ca9 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
/*
 * Copyright 2013-2014 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include <asm/mpc85xx_gpio.h>
#include "ddr.h"

DECLARE_GLOBAL_DATA_PTR;

void fsl_ddr_board_options(memctl_options_t *popts,
				dimm_params_t *pdimm,
				unsigned int ctrl_num)
{
	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
	ulong ddr_freq;

	if (ctrl_num > 2) {
		printf("Not supported controller number %d\n", ctrl_num);
		return;
	}
	if (!pdimm->n_ranks)
		return;

	pbsp = udimms[0];

	/* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr
	 * freqency and n_banks specified in board_specific_parameters table.
	 */
	ddr_freq = get_ddr_freq(0) / 1000000;
	while (pbsp->datarate_mhz_high) {
		if (pbsp->n_ranks == pdimm->n_ranks &&
		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
			if (ddr_freq <= pbsp->datarate_mhz_high) {
				popts->clk_adjust = pbsp->clk_adjust;
				popts->wrlvl_start = pbsp->wrlvl_start;
				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
				goto found;
			}
			pbsp_highest = pbsp;
		}
		pbsp++;
	}

	if (pbsp_highest) {
		printf("Error: board specific timing not found\n");
		printf("for data rate %lu MT/s\n", ddr_freq);
		printf("Trying to use the highest speed (%u) parameters\n",
		       pbsp_highest->datarate_mhz_high);
		popts->clk_adjust = pbsp_highest->clk_adjust;
		popts->wrlvl_start = pbsp_highest->wrlvl_start;
		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
	} else {
		panic("DIMM is not supported by this board");
	}
found:
	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
		"wrlvl_ctrl_3 0x%x\n",
		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
		pbsp->wrlvl_ctl_3);

	/*
	 * Factors to consider for half-strength driver enable:
	 *	- number of DIMMs installed
	 */
	popts->half_strength_driver_enable = 1;
	/*
	 * Write leveling override
	 */
	popts->wrlvl_override = 1;
	popts->wrlvl_sample = 0xf;

	/*
	 * rtt and rtt_wr override
	 */
	popts->rtt_override = 0;

	/* Enable ZQ calibration */
	popts->zq_en = 1;

	/* DHC_EN =1, ODT = 75 Ohm */
#ifdef CONFIG_SYS_FSL_DDR4
	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */

	/* optimize cpo for erratum A-009942 */
	popts->cpo_sample = 0x69;
#else
	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
#endif
}

#if defined(CONFIG_DEEP_SLEEP)
void board_mem_sleep_setup(void)
{
	void __iomem *qixis_base = (void *)QIXIS_BASE;

	/* does not provide HW signals for power management */
	clrbits_8(qixis_base + 0x21, 0x2);
	/* Disable MCKE isolation */
	gpio_set_value(2, 0);
	udelay(1);
}
#endif

phys_size_t initdram(void)
{
	phys_size_t dram_size;

	puts("Initializing....using SPD\n");

	dram_size = fsl_ddr_sdram();

	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
	dram_size *= 0x100000;

	puts("    DDR: ");

#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
	fsl_dp_resume();
#endif

	return dram_size;
}