/* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright (c) 2017 Toradex, Inc. * * Configuration settings for the Toradex Apalis TK1 modules. */ #ifndef __CONFIG_H #define __CONFIG_H #include #include "tegra124-common.h" #define CONFIG_ARCH_MISC_INIT /* Board-specific serial config */ #define CONFIG_TEGRA_ENABLE_UARTA #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE /* Environment in eMMC, before config block at the end of 1st "boot sector" */ #define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE + \ CONFIG_TDX_CFG_BLOCK_OFFSET) #define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_SYS_MMC_ENV_PART 1 /* PCI host support */ #undef CONFIG_PCI_SCAN_SHOW /* PCI networking support */ #define CONFIG_E1000_NO_NVM /* General networking support */ #define CONFIG_IP_DEFRAG #define CONFIG_TFTP_BLOCKSIZE 16352 #define CONFIG_TFTP_TSIZE #undef CONFIG_IPADDR #define CONFIG_IPADDR 192.168.10.2 #define CONFIG_NETMASK 255.255.255.0 #undef CONFIG_SERVERIP #define CONFIG_SERVERIP 192.168.10.1 #define DFU_ALT_EMMC_INFO "apalis-tk1.img raw 0x0 0x500 mmcpart 1; " \ "boot part 0 1 mmcpart 0; " \ "rootfs part 0 2 mmcpart 0; " \ "uImage fat 0 1 mmcpart 0; " \ "tegra124-apalis-eval.dtb fat 0 1 mmcpart 0" #define EMMC_BOOTCMD \ "emmcargs=ip=off root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait\0" \ "emmcboot=run setup; setenv bootargs ${defargs} ${emmcargs} " \ "${setupargs} ${vidargs}; echo Booting from internal eMMC " \ "chip...; run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \ "${boot_file} && run fdt_fixup && " \ "bootm ${kernel_addr_r} - ${dtbparam}\0" \ "emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \ "${soc}-apalis-${fdt_board}.dtb && " \ "setenv dtbparam ${fdt_addr_r}\0" #define NFS_BOOTCMD \ "nfsargs=ip=:::::eth0:on root=/dev/nfs rw\0" \ "nfsboot=pci enum; run setup; setenv bootargs ${defargs} ${nfsargs} " \ "${setupargs} ${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \ "run nfsdtbload; dhcp ${kernel_addr_r} " \ "&& run fdt_fixup && bootm ${kernel_addr_r} - ${dtbparam}\0" \ "nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} " \ "${soc}-apalis-${fdt_board}.dtb " \ "&& setenv dtbparam ${fdt_addr_r}\0" #define SD_BOOTCMD \ "sdargs=ip=off root=/dev/mmcblk1p2 rw rootfstype=ext4 rootwait\0" \ "sdboot=run setup; setenv bootargs ${defargs} ${sdargs} ${setupargs} " \ "${vidargs}; echo Booting from SD card in 8bit slot...; " \ "run sddtbload; load mmc 1:1 ${kernel_addr_r} " \ "${boot_file} && run fdt_fixup && " \ "bootm ${kernel_addr_r} - ${dtbparam}\0" \ "sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \ "${soc}-apalis-${fdt_board}.dtb " \ "&& setenv dtbparam ${fdt_addr_r}\0" #define USB_BOOTCMD \ "usbargs=ip=off root=/dev/sda2 rw rootfstype=ext4 rootwait\0" \ "usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \ "${usbargs} ${vidargs}; echo Booting from USB stick...; " \ "usb start && run usbdtbload; load usb 0:1 ${kernel_addr_r} " \ "${boot_file} && run fdt_fixup && " \ "bootm ${kernel_addr_r} - ${dtbparam}\0" \ "usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \ "${soc}-apalis-${fdt_board}.dtb " \ "&& setenv dtbparam ${fdt_addr_r}\0" #define BOARD_EXTRA_ENV_SETTINGS \ "boot_file=uImage\0" \ "console=ttyS0\0" \ "defargs=lp0_vec=2064@0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \ "usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0\0" \ "dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \ EMMC_BOOTCMD \ "fdt_board=eval\0" \ "fdt_fixup=;\0" \ NFS_BOOTCMD \ SD_BOOTCMD \ "setethupdate=if env exists ethaddr; then; else setenv ethaddr " \ "00:14:2d:00:00:00; fi; pci enum && tftpboot ${loadaddr} " \ "flash_eth.img && source ${loadaddr}\0" \ "setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; " \ "load ${interface} ${drive}:1 ${loadaddr} flash_blk.img " \ "|| setenv drive 2; mmc rescan; load ${interface} ${drive}:1 " \ "${loadaddr} flash_blk.img && " \ "source ${loadaddr}\0" \ "setup=setenv setupargs igb_mac=${ethaddr} " \ "consoleblank=0 no_console_suspend=1 console=tty1 " \ "console=${console},${baudrate}n8 debug_uartport=lsport,0 " \ "${memargs}\0" \ "setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \ "setusbupdate=usb start && setenv interface usb; setenv drive 0; " \ "load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \ "source ${loadaddr}\0" \ USB_BOOTCMD \ "vidargs=video=tegrafb0:640x480-16@60 fbcon=map:1\0" /* Increase console I/O buffer size */ #undef CONFIG_SYS_CBSIZE #define CONFIG_SYS_CBSIZE 1024 /* Increase arguments buffer size */ #undef CONFIG_SYS_BARGSIZE #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Increase maximum number of arguments */ #undef CONFIG_SYS_MAXARGS #define CONFIG_SYS_MAXARGS 32 #define CONFIG_CMD_TIME #define CONFIG_SYS_BOOT_RAMDISK_HIGH #include "tegra-common-usb-gadget.h" #include "tegra-common-post.h" /* Reserve top 1M for secure RAM */ #define CONFIG_ARMV7_SECURE_BASE 0xfff00000 #define CONFIG_ARMV7_SECURE_RESERVE_SIZE 0x00100000 #endif /* __CONFIG_H */