From 0c81f37d9a22b38368296ffd9ea008add8657f7d Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Sun, 30 Aug 2015 19:19:29 -0600 Subject: arm: Remove tt01 board This board has not been converted to generic board by the deadline. Remove it. Signed-off-by: Simon Glass --- include/configs/tt01.h | 266 ------------------------------------------------- 1 file changed, 266 deletions(-) delete mode 100644 include/configs/tt01.h (limited to 'include/configs') diff --git a/include/configs/tt01.h b/include/configs/tt01.h deleted file mode 100644 index ca1e2e25fb..0000000000 --- a/include/configs/tt01.h +++ /dev/null @@ -1,266 +0,0 @@ -/* - * (C) Copyright 2011 HALE electronic - * (C) Copyright 2008 Magnus Lilja - * - * Configuration settings for the HALE TT-01 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include - -/* High Level Configuration Options */ -#define CONFIG_MX31 - -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_MACH_TYPE 3726 /* not yet in mach-types.h */ -#define CONFIG_SYS_TEXT_BASE 0xA0000000 - - -/* - * Physical Memory Map: - * CS settings are defined by i.MX31: - * - CSD0 and CDS1 are 256MB each, starting at 0x80000000 and 0x9000000 - * - CS0 and CS1 are 128MB each, at A0000000 and A8000000 - * - CS2 to CS5 are 32MB each, at B0.., B2.., B4.., B6.. - * - * HALE set-up of the bluetechnix board for now is: - * - 128MB DDR (2x64MB, 2x16bit), connected to 32bit DDR ram interface - * - NOR-Flash (Spansion 32MB MCP, Flash+16MB PSRAM), 16bit interface at CS0 - * - S71WS256ND0BFWYM (and CS1 for 64MB S71WS512ND0 without PSRAM) - * the flash chip is a mirrorbit S29WS256N ! - * - the PSRAM is hooked to CS5 (0xB6000000) - * - Intel Strata Flash PF48F2000P0ZB00, 16bit interface at (CS0 or) CS1 - * - 64Mbit = 8MByte (will go away in the production set-up) - * - NAND-Flash NAND01GR3B2BZA6 at NAND-FC: - * 1Gbit=128MB, 2048+64 bytes/page, 64pages x 1024 blocks - * - Ethernet controller SMC9118 at CS4 via FPGA, 16bit interface - * - * u-boot will support the 32MB nor flash and the 128MB NAND flash, the PSRAM - * is not used right now. We should be able to reduce the SOM to NAND flash - * only and boot from there. - */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 CSD0_BASE -#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024) - -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_BOARD_LATE_INIT - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR -#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET) - -/* default load address, 1MB up the road */ -#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1+0x100000) - -/* Size of malloc() pool, make sure possible frame buffer fits */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 10*1024*1024) - -/* memtest works on all but the last 1MB (u-boot) and malloc area */ -#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 -#define CONFIG_SYS_MEMTEST_END \ - (PHYS_SDRAM_1+(PHYS_SDRAM_1_SIZE-CONFIG_SYS_MALLOC_LEN-0x100000)) - -/* CFI FLASH driver setup */ -#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */ -#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */ -#define CONFIG_FLASH_SPANSION_S29WS_N -/* - * TODO: Bluetechnix (the supplier of the SOM) did define these values - * in their original version of u-boot (1.2 or so). This should be - * reviewed. - * - * #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE - * #define CONFIG_SYS_FLASH_PROTECTION - */ -#define CONFIG_SYS_FLASH_BASE CS0_BASE -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT (254+8) /* max number of sectors per chip */ - -/* - * FLASH and environment organization, only the Spansion chip is supported: - * - it has 254 * 128kB + 8 * 32kB blocks - * - this setup uses 4*32k+3*128k as monitor space = 0xA000 0000 to 0xA00F FFFF - * and 2 sectors with 128k as environment = - * A010 0000 to 0xA011 FFFF and 0xA012 0000 to 0xA013 FFFF - * - this could be less, but this is only for developer versions of the board - * and no-one is going to use the NOR flash anyway. - * - * Monitor is at the beginning of the NOR-Flash, 1MB reserved. Again this is - * way to large, but it avoids ENV overwrite (when updating u-boot) in case - * size breaks the next boundary (as it has with 128k). - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (1024 * 1024) - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE (128 * 1024) - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - -/* Hardware drivers */ - -/* - * on TT-01 UART1 pins are used by Audio, so we use UART2 - * TT-01 implements a hardware that turns off components depending on - * the power level. In PL=1 the RS232 transceiver is usually off, - * make sure that the transceiver is enabled during PL=1 for testing! - */ -#define CONFIG_MXC_UART -#define CONFIG_MXC_UART_BASE UART2_BASE - -#define CONFIG_MXC_SPI -#define CONFIG_MXC_GPIO - -/* MC13783 connected to CSPI3 and SS0 */ -#define CONFIG_POWER -#define CONFIG_POWER_SPI -#define CONFIG_POWER_FSL - -#define CONFIG_FSL_PMIC_BUS 2 -#define CONFIG_FSL_PMIC_CS 0 -#define CONFIG_FSL_PMIC_CLK 1000000 -#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) -#define CONFIG_FSL_PMIC_BITLEN 32 - -#define CONFIG_RTC_MC13XXX - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -/* console is UART2 on TT-01 */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* ethernet setup for the onboard smc9118 */ -#define CONFIG_MII -#define CONFIG_SMC911X -/* 16 bit, onboard ethernet, decoded via MACH-MX0 FPGA at 0x84200000 */ -#define CONFIG_SMC911X_BASE (CS4_BASE+0x200000) -#define CONFIG_SMC911X_16_BIT - -/* mmc driver */ -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_MXC_MMC -#define CONFIG_MXC_MCI_REGS_BASE SDHC1_BASE_ADDR - -/* video support */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_MX3 -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -/* splash image won't work with NAND boot, use preboot script */ -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_CONSOLE_EXTRA_INFO /* display additional board info */ -#define CONFIG_VGA_AS_SINGLE_DEVICE /* display is an output only device */ - -/* allow stdin, stdout and stderr variables to redirect output */ -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_SILENT_CONSOLE /* UARTs used externally (release) */ -#define CONFIG_SYS_DEVICE_NULLDEV /* allow console to be turned off */ -#define CONFIG_PREBOOT - -/* allow decompressing max. 4MB */ -#define CONFIG_VIDEO_BMP_GZIP -/* this is not only used by cfb_console.c for the logo, but also in cmd_bmp.c */ -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4*1024*1024) - -/* - * Command definition - */ -#define CONFIG_CMD_DATE -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NAND -/* - * #define CONFIG_CMD_NAND_LOCK_UNLOCK the NAND01... chip does not support - * the NAND_CMD_LOCK_STATUS command, however the NFC of i.MX31 supports - * a software locking scheme. - */ -#define CONFIG_CMD_BMP - -#define CONFIG_BOOTDELAY 3 - -/* - * currently a default setting for booting via script is implemented - * set user to login name and serverip to tftp host, define your - * boot behaviour in bootscript.loginname - * - * TT-01 board specific TFT setup (used by drivers/video/mx3fb.c) - * - * This set-up is for the L5F30947T04 by Epson, which is - * 800x480, 33MHz pixel clock, 60Hz vsync, 31.6kHz hsync - * sync must be set to: DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ -"videomode=epson\0" \ -"epson=video=ctfb:x:800,y:480,depth:16,mode:0,pclk:30076," \ - "le:215,ri:1,up:32,lo:13,hs:7,vs:10,sync:100663296,vmode:0\0" \ -"bootcmd=dhcp bootscript.${user}; source\0" - -#define CONFIG_BOOTP_SERVERIP /* tftp serverip not overruled by dhcp server */ -#define CONFIG_BOOTP_SEND_HOSTNAME /* if env-var 'hostname' is set, send it */ - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_HUSH_PARSER - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_CMDLINE_EDITING - -/* MMC boot support */ -#define CONFIG_CMD_MMC -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT - -#define CONFIG_NAND_MXC -#define CONFIG_SYS_MAX_NAND_DEVICE 1 - -/* - * actually this is nothing someone wants to configure! - * CONFIG_SYS_NAND_BASE despite being passed to board_nand_init() - * is not used by the driver. - */ -#define CONFIG_MXC_NAND_REGS_BASE NFC_BASE_ADDR -#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR -#define CONFIG_MXC_NAND_HWECC - -/* the current u-boot driver does not use the nand flash setup! */ -#define CONFIG_SYS_NAND_LARGEPAGE -/* - * it's not 16 bit: - * #define CONFIG_SYS_NAND_BUSWIDTH_16BIT - * the current u-boot mxc_nand.c tries to auto-detect, but this only - * reads the boot settings during reset (which might be wrong) - */ - -#endif /* __CONFIG_H */ -- cgit v1.2.3