From af895e4527c3870dc73fb879f7a8610e4ae70ca6 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 22 Feb 2011 08:58:19 +0100 Subject: ppc: add support for ppc based board mgcoge2ne The mgcoge2 board from keymile deploys two different processors. An ARM based Kirkwood for the "unit" part of the SW and a PPC for the "ne" part of the SW. Therefore in Linux and U-Boot the names for the board are mgcoge2un and mgcoge2ne. This patch adds the mgcoge2ne part of the board. The ppc part of mgboge2 is quite similar to mgcoge, therefore a generic header km82xx-common.h was introduced to collect all similiarities. Currently the only difference is that mgcoge2ne has a 64 MB numonyx NOR flash with a single die. The mgcoge has a dual die flash 2*32MB from spansion. Signed-off-by: Holger Brunck Signed-off-by: Heiko Schocher cc: Wolfgang Denk cc: Valentin Longchamp --- include/configs/mgcoge.h | 312 +---------------------------------------------- 1 file changed, 3 insertions(+), 309 deletions(-) (limited to 'include/configs/mgcoge.h') diff --git a/include/configs/mgcoge.h b/include/configs/mgcoge.h index a7222f465c..a0d1765adf 100644 --- a/include/configs/mgcoge.h +++ b/include/configs/mgcoge.h @@ -39,72 +39,6 @@ #include "keymile-common.h" #include "km-powerpc.h" -/* - * Select serial console configuration - * - * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - */ -#define CONFIG_CONS_ON_SMC /* Console is on SMC */ -#undef CONFIG_CONS_ON_SCC /* It's not on SCC */ -#undef CONFIG_CONS_NONE /* It's not on external UART */ -#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */ -#define CONFIG_SYS_SMC_RXBUFLEN 128 -#define CONFIG_SYS_MAXIDLE 10 - -/* - * Select ethernet configuration - * - * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, - * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for - * SCC, 1-3 for FCC) - * - * If CONFIG_ETHER_NONE is defined, then either the ethernet routines - * must be defined elsewhere (as for the console), or CONFIG_CMD_NET - * must be unset. - */ -#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */ -#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */ -#undef CONFIG_ETHER_NONE /* No external Ethernet */ -#define CONFIG_NET_MULTI - -#define CONFIG_ETHER_INDEX 4 -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_SCC_TOUT_LOOP 10000000 - -# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8) - -#ifndef CONFIG_8260_CLKIN -#define CONFIG_8260_CLKIN 66000000 /* in Hz */ -#endif - -#define BOOTFLASH_START 0xFE000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyCPM0" - -#define MTDIDS_DEFAULT "nor3=app" -#define MTDPARTS_DEFAULT "mtdparts=" \ - "app:" \ - "768k(u-boot)," \ - "128k(env)," \ - "128k(envred)," \ - "3072k(free)," \ - "-(" CONFIG_KM_UBI_PARTITION_NAME ")" - -/* - * Default environment settings - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - "EEprom_ivm=pca9544a:70:4 \0" \ - "unlock=yes\0" \ - "newenv=" \ - "prot off 0xFE0C0000 +0x40000 && " \ - "era 0xFE0C0000 +0x40000\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "" - #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFE000000 #define CONFIG_SYS_FLASH_SIZE 32 @@ -122,250 +56,10 @@ #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \ CONFIG_SYS_FLASH_BASE_1, \ CONFIG_SYS_FLASH_BASE_2 } +#define MTDIDS_DEFAULT "nor3=app" -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (768 << 10) - -#define CONFIG_ENV_IS_IN_FLASH - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ -#define CONFIG_ENV_BUFFER_PRINT - -/* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * Software (bit-bang) I2C driver configuration - */ - -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00010000) -#define I2C_TRISTATE (iop->pdir &= ~0x00010000) -#define I2C_READ ((iop->pdat & 0x00010000) != 0) -#define I2C_SDA(bit) do { \ - if (bit) \ - iop->pdat |= 0x00010000; \ - else \ - iop->pdat &= ~0x00010000; \ - } while (0) -#define I2C_SCL(bit) do { \ - if (bit) \ - iop->pdat |= 0x00020000; \ - else \ - iop->pdat &= ~0x00020000; \ - } while (0) -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) - -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -#define CONFIG_SYS_IMMR 0xF0000000 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* Hard reset configuration word */ -#define CONFIG_SYS_HRCW_MASTER 0x0604b211 - -/* No slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) - -#define CONFIG_SYS_HID2 0 - -#define CONFIG_SYS_SIUMCR 0x4020c200 -#define CONFIG_SYS_SYPCR 0xFFFFFFC3 -#define CONFIG_SYS_BCR 0x10000000 -#define CONFIG_SYS_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK) - -/* - *----------------------------------------------------------------------- - * RMR - Reset Mode Register 5-5 - *----------------------------------------------------------------------- - * turn on Checkstop Reset Enable - */ -#define CONFIG_SYS_RMR 0 - -/* - *----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) - -/* - *----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) - -/* - *----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Init Memory Controller: - * - * Bank Bus Machine PortSz Device - * ---- --- ------- ------ ------ - * 0 60x GPCM 8 bit FLASH - * 1 60x SDRAM 32 bit SDRAM - * 3 60x GPCM 8 bit GPIO/PIGGY - * 5 60x GPCM 16 bit CFG-Flash - * - */ -/* Bank 0 - FLASH - */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ - BRx_PS_8 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV2 |\ - ORxG_SCY_5_CLK |\ - ORxG_TRLX ) - - -/* - * Bank 1 - 60x bus SDRAM - */ -#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ -#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) - -#define CONFIG_SYS_MPTPR 0x1800 - -/* - *----------------------------------------------------------------------------- - * Address for Mode Register Set (MRS) command - *----------------------------------------------------------------------------- - */ -#define CONFIG_SYS_MRS_OFFS 0x00000110 -#define CONFIG_SYS_PSRT 0x0e - -#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1 - -/* - * SDRAM initialization values - */ - -#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_8 |\ - ORxS_ROWST_PBI0_A7 |\ - ORxS_NUMR_13) - -#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\ - PSDMR_BSMA_A14_A16 |\ - PSDMR_SDA10_PBI0_A9 |\ - PSDMR_RFRC_5_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_1C |\ - PSDMR_CL_2) - -/* - * GPIO/PIGGY on CS3 initialization values - */ -#define CONFIG_SYS_PIGGY_BASE 0x30000000 -#define CONFIG_SYS_PIGGY_SIZE 128 - -#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\ - BRx_PS_8 | BRx_MS_GPCM_P | BRx_V) - -#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\ - ORxG_CSNT | ORxG_ACS_DIV2 |\ - ORxG_SCY_3_CLK | ORxG_TRLX ) - -/* - * Board FPGA on CS4 initialization values - */ -#define CONFIG_SYS_FPGA_BASE 0x40000000 -#define CONFIG_SYS_FPGA_SIZE 1 /*1KB*/ - -#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\ - BRx_PS_8 | BRx_MS_GPCM_P | BRx_V) - -#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\ - ORxG_CSNT | ORxG_ACS_DIV2 |\ - ORxG_SCY_3_CLK | ORxG_TRLX ) - -/* - * CFG-Flash on CS5 initialization values - */ -#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\ - BRx_PS_16 | BRx_MS_GPCM_P | BRx_V) - -#define CONFIG_SYS_OR5_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1 + \ - CONFIG_SYS_FLASH_SIZE_2) |\ - ORxG_CSNT | ORxG_ACS_DIV2 |\ - ORxG_SCY_5_CLK | ORxG_TRLX ) - -#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ - -/* pass open firmware flat tree */ -#define CONFIG_FIT -#define CONFIG_OF_LIBFDT -#define CONFIG_OF_BOARD_SETUP - -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc/cpm/serial@11a90" +/* include further common stuff for all keymile 82xx boards */ +#include "km82xx-common.h" /* enable last_stage_init */ #define CONFIG_LAST_STAGE_INIT 1 -- cgit v1.2.3