From 7a8979591171676417ab36852d8811a8c46accd8 Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Wed, 29 Oct 2008 12:39:26 -0500 Subject: pci/fsl_pci_init: Enable inbound PCI config cycles Add fsl_pci_config_unlock() function to enable a PCI/PCIe interface configured in agent/endpoint mode to respond to inbound PCI configuration cycles. Signed-off-by: Peter Tyser --- drivers/pci/fsl_pci_init.c | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) (limited to 'drivers') diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c index 1db42fd8d3..db68f26009 100644 --- a/drivers/pci/fsl_pci_init.c +++ b/drivers/pci/fsl_pci_init.c @@ -37,6 +37,11 @@ DECLARE_GLOBAL_DATA_PTR; #include #include +/* Freescale-specific PCI config registers */ +#define FSL_PCI_PBFR 0x44 +#define FSL_PCIE_CAP_ID 0x4c +#define FSL_PCIE_CFG_RDY 0x4b0 + void pciauto_prescan_setup_bridge(struct pci_controller *hose, pci_dev_t dev, int sub_bus); void pciauto_postscan_setup_bridge(struct pci_controller *hose, @@ -306,6 +311,30 @@ void fsl_pci_init(struct pci_controller *hose) } } +/* Enable inbound PCI config cycles for agent/endpoint interface */ +void fsl_pci_config_unlock(struct pci_controller *hose) +{ + pci_dev_t dev = PCI_BDF(hose->first_busno,0,0); + u8 agent; + u8 pcie_cap; + u16 pbfr; + + pci_hose_read_config_byte(hose, dev, PCI_CLASS_PROG, &agent); + if (!agent) + return; + + pci_hose_read_config_byte(hose, dev, FSL_PCIE_CAP_ID, &pcie_cap); + if (pcie_cap != 0x0) { + /* PCIe - set CFG_READY bit of Configuration Ready Register */ + pci_hose_write_config_byte(hose, dev, FSL_PCIE_CFG_RDY, 0x1); + } else { + /* PCI - clear ACL bit of PBFR */ + pci_hose_read_config_word(hose, dev, FSL_PCI_PBFR, &pbfr); + pbfr &= ~0x20; + pci_hose_write_config_word(hose, dev, FSL_PCI_PBFR, pbfr); + } +} + #ifdef CONFIG_OF_BOARD_SETUP #include #include -- cgit v1.2.3 From e92739d34e2d6b6aca93b2598248210710897ce8 Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Wed, 17 Dec 2008 16:36:21 -0600 Subject: Add support for PCA953x I2C gpio devices Initial support for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc). The CONFIG_PCA953X define enables support for the devices while the CONFIG_CMD_PCA953X define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO define enables an 'info' sub-command which provides summary information for the given pca953x device. Signed-off-by: Peter Tyser --- drivers/gpio/Makefile | 47 ++++++++++ drivers/gpio/pca953x.c | 227 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 274 insertions(+) create mode 100644 drivers/gpio/Makefile create mode 100644 drivers/gpio/pca953x.c (limited to 'drivers') diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile new file mode 100644 index 0000000000..dd618ed71c --- /dev/null +++ b/drivers/gpio/Makefile @@ -0,0 +1,47 @@ +# +# Copyright 2000-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB := $(obj)libgpio.a + +COBJS-$(CONFIG_PCA953X) += pca953x.o + +COBJS := $(COBJS-y) +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +all: $(LIB) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################## diff --git a/drivers/gpio/pca953x.c b/drivers/gpio/pca953x.c new file mode 100644 index 0000000000..390d99ad3d --- /dev/null +++ b/drivers/gpio/pca953x.c @@ -0,0 +1,227 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Driver for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc) + * TODO: support additional devices with more than 8-bits GPIO + */ + +#include +#include +#include + +/* Default to an address that hopefully won't corrupt other i2c devices */ +#ifndef CONFIG_SYS_I2C_PCA953X_ADDR +#define CONFIG_SYS_I2C_PCA953X_ADDR (~0) +#endif + +enum { + PCA953X_CMD_INFO, + PCA953X_CMD_DEVICE, + PCA953X_CMD_OUTPUT, + PCA953X_CMD_INPUT, + PCA953X_CMD_INVERT, +}; + +/* + * Modify masked bits in register + */ +static int pca953x_reg_write(uint8_t chip, uint addr, uint mask, uint data) +{ + uint8_t val; + + if (i2c_read(chip, addr, 1, &val, 1)) + return -1; + + val &= ~mask; + val |= data; + + return i2c_write(chip, addr, 1, &val, 1); +} + +/* + * Set output value of IO pins in 'mask' to corresponding value in 'data' + * 0 = low, 1 = high + */ +int pca953x_set_val(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_OUT, mask, data); +} + +/* + * Set read polarity of IO pins in 'mask' to corresponding value in 'data' + * 0 = read pin value, 1 = read inverted pin value + */ +int pca953x_set_pol(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_POL, mask, data); +} + +/* + * Set direction of IO pins in 'mask' to corresponding value in 'data' + * 0 = output, 1 = input + */ +int pca953x_set_dir(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_CONF, mask, data); +} + +/* + * Read current logic level of all IO pins + */ +int pca953x_get_val(uint8_t chip) +{ + uint8_t val; + + if (i2c_read(chip, 0, 1, &val, 1)) + return -1; + + return (int)val; +} + +#ifdef CONFIG_CMD_PCA953X +#ifdef CONFIG_CMD_PCA953X_INFO +/* + * Display pca953x information + */ +static int pca953x_info(uint8_t chip) +{ + int i; + uint8_t data; + + printf("pca953x@ 0x%x:\n\n", chip); + printf("gpio pins: 76543210\n"); + printf("-------------------\n"); + + if (i2c_read(chip, PCA953X_CONF, 1, &data, 1)) + return -1; + printf("conf: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? 'i' : 'o'); + printf("\n"); + + if (i2c_read(chip, PCA953X_POL, 1, &data, 1)) + return -1; + printf("invert: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + if (i2c_read(chip, PCA953X_IN, 1, &data, 1)) + return -1; + printf("input: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + if (i2c_read(chip, PCA953X_OUT, 1, &data, 1)) + return -1; + printf("output: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + return 0; +} +#endif /* CONFIG_CMD_PCA953X_INFO */ + +cmd_tbl_t cmd_pca953x[] = { + U_BOOT_CMD_MKENT(device, 3, 0, (void *)PCA953X_CMD_DEVICE, "", ""), + U_BOOT_CMD_MKENT(output, 4, 0, (void *)PCA953X_CMD_OUTPUT, "", ""), + U_BOOT_CMD_MKENT(input, 3, 0, (void *)PCA953X_CMD_INPUT, "", ""), + U_BOOT_CMD_MKENT(invert, 4, 0, (void *)PCA953X_CMD_INVERT, "", ""), +#ifdef CONFIG_CMD_PCA953X_INFO + U_BOOT_CMD_MKENT(info, 2, 0, (void *)PCA953X_CMD_INFO, "", ""), +#endif +}; + +int do_pca953x(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + static uint8_t chip = CONFIG_SYS_I2C_PCA953X_ADDR; + int val; + ulong ul_arg2 = 0; + ulong ul_arg3 = 0; + cmd_tbl_t *c; + + c = find_cmd_tbl(argv[1], cmd_pca953x, ARRAY_SIZE(cmd_pca953x)); + + /* All commands but "device" require 'maxargs' arguments */ + if (!c || !((argc == (c->maxargs)) || + (((int)c->cmd == PCA953X_CMD_DEVICE) && + (argc == (c->maxargs - 1))))) { + printf("Usage:\n%s\n", cmdtp->usage); + return 1; + } + + /* arg2 used as chip number or pin number */ + if (argc > 2) + ul_arg2 = simple_strtoul(argv[2], NULL, 16); + + /* arg3 used as pin or invert value */ + if (argc > 3) + ul_arg3 = simple_strtoul(argv[3], NULL, 16) & 0x1; + + switch ((int)c->cmd) { +#ifdef CONFIG_CMD_PCA953X_INFO + case PCA953X_CMD_INFO: + return pca953x_info(chip); +#endif + case PCA953X_CMD_DEVICE: + if (argc == 3) + chip = (uint8_t)ul_arg2; + printf("Current device address: 0x%x\n", chip); + return 0; + case PCA953X_CMD_INPUT: + pca953x_set_dir(chip, (1 << ul_arg2), + PCA953X_DIR_IN << ul_arg2); + val = (pca953x_get_val(chip) & (1 << ul_arg2)) != 0; + + printf("chip 0x%02x, pin 0x%lx = %d\n", chip, ul_arg2, val); + return val; + case PCA953X_CMD_OUTPUT: + pca953x_set_dir(chip, (1 << ul_arg2), + (PCA953X_DIR_OUT << ul_arg2)); + return pca953x_set_val(chip, (1 << ul_arg2), + (ul_arg3 << ul_arg2)); + case PCA953X_CMD_INVERT: + return pca953x_set_pol(chip, (1 << ul_arg2), + (ul_arg3 << ul_arg2)); + default: + /* We should never get here */ + return 1; + } +} + +U_BOOT_CMD( + pca953x, 5, 1, do_pca953x, + "pca953x - pca953x gpio access\n", + "device [dev]\n" + " - show or set current device address\n" +#ifdef CONFIG_CMD_PCA953X_INFO + "pca953x info\n" + " - display info for current chip\n" +#endif + "pca953x output pin 0|1\n" + " - set pin as output and drive low or high\n" + "pca953x invert pin 0|1\n" + " - disable/enable polarity inversion for reads\n" + "pca953x intput pin\n" + " - set pin as input and read value\n" +); + +#endif /* CONFIG_CMD_PCA953X */ -- cgit v1.2.3 From 9d94aff699eed38b286814fcbb335f3eb8516a0e Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 16 Dec 2008 14:59:22 -0600 Subject: NAND FSL elbc: Use virt_to_phys to determine which bank is in use The current code that determines which bank/chipselect is used for a given NAND instance only worked for 32-bit addresses and assumed a 1:1 mapping. This breaks in 36-bit physical configs. The proper way to handle this is to use the virt_to_phys() and BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address with the the virtual address the NAND code uses. Signed-off-by: Kumar Gala Acked-by: Scott Wood --- drivers/mtd/nand/fsl_elbc_nand.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index 367c7d7fcd..3f318e02e2 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -718,7 +718,7 @@ static void fsl_elbc_ctrl_init(void) int board_nand_init(struct nand_chip *nand) { struct fsl_elbc_mtd *priv; - uint32_t br, or; + uint32_t br = 0, or = 0; if (!elbc_ctrl) { fsl_elbc_ctrl_init(); @@ -737,11 +737,13 @@ int board_nand_init(struct nand_chip *nand) * if we could pass more than one datum to the NAND driver... */ for (priv->bank = 0; priv->bank < MAX_BANKS; priv->bank++) { + phys_addr_t base_addr = virt_to_phys(nand->IO_ADDR_R); + br = in_be32(&elbc_ctrl->regs->bank[priv->bank].br); or = in_be32(&elbc_ctrl->regs->bank[priv->bank].or); if ((br & BR_V) && (br & BR_MSEL) == BR_MS_FCM && - (br & or & BR_BA) == (phys_addr_t)nand->IO_ADDR_R) + (br & or & BR_BA) == BR_PHYS_ADDR(base_addr)) break; } -- cgit v1.2.3