From 910f1ae3eb05533ac0c7f7fe5b31b50b91f7f0e1 Mon Sep 17 00:00:00 2001 From: John Rigby Date: Tue, 19 Apr 2011 10:42:39 +0000 Subject: Serial: p1011: new vendor init options Two new options: CONFIG_PL011_SERIAL_RLCR Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500) have separate receive and transmit line control registers. Set this variable to initialize the extra register. CONFIG_PL011_SERIAL_FLUSH_ON_INIT On some platforms (e.g. U8500) U-Boot is loaded by a second stage boot loader that has already initialized the UART. Define this variable to flush the UART at init time. empty fifo on init Signed-off-by: John Rigby Signed-off-by: Rabin Vincent --- drivers/serial/serial_pl01x.c | 30 +++++++++++++++++++++++++++--- drivers/serial/serial_pl01x.h | 4 ++++ 2 files changed, 31 insertions(+), 3 deletions(-) (limited to 'drivers/serial') diff --git a/drivers/serial/serial_pl01x.c b/drivers/serial/serial_pl01x.c index 5dfcde8774..7a064ffb24 100644 --- a/drivers/serial/serial_pl01x.c +++ b/drivers/serial/serial_pl01x.c @@ -111,6 +111,15 @@ int serial_init (void) unsigned int divider; unsigned int remainder; unsigned int fraction; + unsigned int lcr; + +#ifdef CONFIG_PL011_SERIAL_FLUSH_ON_INIT + /* Empty RX fifo if necessary */ + if (readl(®s->pl011_cr) & UART_PL011_CR_UARTEN) { + while (!(readl(®s->fr) & UART_PL01x_FR_RXFE)) + readl(®s->dr); + } +#endif /* First, disable everything */ writel(0, ®s->pl011_cr); @@ -131,9 +140,24 @@ int serial_init (void) writel(fraction, ®s->pl011_fbrd); /* Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled */ - writel(UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN, - ®s->pl011_lcrh); - + lcr = UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN; + writel(lcr, ®s->pl011_lcrh); + +#ifdef CONFIG_PL011_SERIAL_RLCR + { + int i; + + /* + * Program receive line control register after waiting + * 10 bus cycles. Delay be writing to readonly register + * 10 times + */ + for (i = 0; i < 10; i++) + writel(lcr, ®s->fr); + + writel(lcr, ®s->pl011_rlcr); + } +#endif /* Finally, enable the UART */ writel(UART_PL011_CR_UARTEN | UART_PL011_CR_TXE | UART_PL011_CR_RXE, ®s->pl011_cr); diff --git a/drivers/serial/serial_pl01x.h b/drivers/serial/serial_pl01x.h index b670c24e11..96ee3819ed 100644 --- a/drivers/serial/serial_pl01x.h +++ b/drivers/serial/serial_pl01x.h @@ -43,7 +43,11 @@ struct pl01x_regs { u32 pl010_lcrl; /* 0x10 Line control register, low byte */ u32 pl010_cr; /* 0x14 Control register */ u32 fr; /* 0x18 Flag register (Read only) */ +#ifdef CONFIG_PL011_SERIAL_RLCR + u32 pl011_rlcr; /* 0x1c Receive line control register */ +#else u32 reserved; +#endif u32 ilpr; /* 0x20 IrDA low-power counter register */ u32 pl011_ibrd; /* 0x24 Integer baud rate register */ u32 pl011_fbrd; /* 0x28 Fractional baud rate register */ -- cgit v1.2.3