From a187559e3d586891c917279044c5386d1b2adc6e Mon Sep 17 00:00:00 2001 From: Bin Meng Date: Fri, 5 Feb 2016 19:30:11 -0800 Subject: Use correct spelling of "U-Boot" Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng Reviewed-by: Heiko Schocher Reviewed-by: Simon Glass Reviewed-by: Minkyu Kang --- doc/README.mxs | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'doc/README.mxs') diff --git a/doc/README.mxs b/doc/README.mxs index ed2e568856..6ea73b9d5b 100644 --- a/doc/README.mxs +++ b/doc/README.mxs @@ -1,4 +1,4 @@ -Booting U-boot on a MXS processor +Booting U-Boot on a MXS processor ================================= This document describes the MXS U-Boot port. This document mostly covers topics @@ -23,7 +23,7 @@ Contents 2) Compiling U-Boot for a MXS based board 3) Installation of U-Boot for a MXS based board to SD card 4) Installation of U-Boot into NAND flash on a MX28 based board -5) Installation of U-boot into SPI NOR flash on a MX28 based board +5) Installation of U-Boot into SPI NOR flash on a MX28 based board 1) Prerequisites ---------------- @@ -95,19 +95,19 @@ Next, configure U-Boot for a MXS based board Examples: -1. For building U-boot for Denx M28EVK board: +1. For building U-Boot for Denx M28EVK board: $ make m28evk_config -2. For building U-boot for Freescale MX28EVK board: +2. For building U-Boot for Freescale MX28EVK board: $ make mx28evk_config -3. For building U-boot for Freescale MX23EVK board: +3. For building U-Boot for Freescale MX23EVK board: $ make mx23evk_config -4. For building U-boot for Olimex MX23 Olinuxino board: +4. For building U-Boot for Olimex MX23 Olinuxino board: $ make mx23_olinuxino_config @@ -267,7 +267,7 @@ There are two possibilities when preparing an image writable to NAND flash. 5) Installation of U-Boot into SPI NOR flash on a MX28 based board ------------------------------------------------------------------ -The u-boot.sb file can be directly written to SPI NOR from U-boot prompt. +The u-boot.sb file can be directly written to SPI NOR from U-Boot prompt. Load u-boot.sb into RAM, this can be done in several ways and one way is to use tftp: @@ -278,7 +278,7 @@ Probe the SPI NOR flash: (SPI NOR should be succesfully detected in this step) -Erase the blocks where U-boot binary will be written to: +Erase the blocks where U-Boot binary will be written to: => sf erase 0x0 0x80000 Write u-boot.sb to SPI NOR: @@ -287,4 +287,4 @@ Write u-boot.sb to SPI NOR: Power off the board and set the boot mode DIP switches to boot from the SPI NOR according to MX28 manual section 12.2.1 (Table 12-2) -Last step is to power up the board and U-boot should start from SPI NOR. +Last step is to power up the board and U-Boot should start from SPI NOR. -- cgit v1.2.3