From 702e6014f15b307f144fa03ecaf83a8446c6802a Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 29 Apr 2012 23:57:39 +0000 Subject: doc: cleanup - move board READMEs into respective board directories Also drop a few files referring to no longer / not yet supported boards. Signed-off-by: Wolfgang Denk Cc: Prafulla Wadaskar Cc: Stefan Roese Cc: Kim Phillips Cc: Andy Fleming Cc: Jason Jin Cc: Stefano Babic Cc: Daniel Schwierzeck Acked-by: Stefano Babic Acked-by: Daniel Schwierzeck --- doc/README.bamboo | 77 ------------------------------------------------------- 1 file changed, 77 deletions(-) delete mode 100644 doc/README.bamboo (limited to 'doc/README.bamboo') diff --git a/doc/README.bamboo b/doc/README.bamboo deleted file mode 100644 index e139c6d1295..00000000000 --- a/doc/README.bamboo +++ /dev/null @@ -1,77 +0,0 @@ -The 2 important dipswitches are configured as shown below: - -SW1 (for 33MHz SysClk) ----------------------- -S1 S2 S3 S4 S5 S6 S7 S8 -OFF OFF OFF OFF OFF OFF OFF ON - -SW7 (for Op-Code Flash and Boot Option H) ------------------------------------------ -S1 S2 S3 S4 S5 S6 S7 S8 -OFF OFF OFF ON OFF OFF OFF OFF - -The EEPROM at location 0x52 is loaded with these 16 bytes: -C47042A6 05D7A190 40082350 0d050000 - -SDR0_SDSTP0[ENG]: 1 : PLL's VCO is the source for PLL forward divisors -SDR0_SDSTP0[SRC]: 1 : Feedback originates from PLLOUTB -SDR0_SDSTP0[SEL]: 0 : Feedback selection is PLL output -SDR0_SDSTP0[TUNE]: 1000111000 : 10 <= M <= 22, 600MHz < VCO <= 900MHz -SDR0_SDSTP0[FBDV]: 4 : PLL feedback divisor -SDR0_SDSTP0[FBDVA]: 2 : PLL forward divisor A -SDR0_SDSTP0[FBDVB]: 5 : PLL forward divisor B -SDR0_SDSTP0[PRBDV0]: 1 : PLL primary divisor B -SDR0_SDSTP0[OPBDV0]: 2 : OPB clock divisor -SDR0_SDSTP0[LFBDV]: 1 : PLL local feedback divisor -SDR0_SDSTP0[PERDV0]: 3 : Peripheral clock divisor 0 -SDR0_SDSTP0[MALDV0]: 2 : MAL clock divisor 0 -SDR0_SDSTP0[PCIDV0]: 2 : Sync PCI clock divisor 0 -SDR0_SDSTP0[PLLTIMER]: 7 : PLL locking timer -SDR0_SDSTP0[RW]: 1 : EBC ROM width: 16-bit -SDR0_SDSTP0[RL]: 0 : EBC ROM location: EBC -SDR0_SDSTP0[PAE]: 0 : PCI internal arbiter: disabled -SDR0_SDSTP0[PHCE]: 0 : PCI host configuration: disabled -SDR0_SDSTP0[ZM]: 3 : ZMII mode: RMII mode 100 -SDR0_SDSTP0[CTE]: 0 : CPU trace: disabled -SDR0_SDSTP0[Nto1]: 0 : CPU/PLB ratio N/P: not N to 1 -SDR0_SDSTP0[PAME]: 1 : PCI asynchronous mode: enabled -SDR0_SDSTP0[MEM]: 1 : Multiplex: EMAC -SDR0_SDSTP0[NE]: 0 : NDFC: disabled -SDR0_SDSTP0[NBW]: 0 : NDFC boot width: 8-bit -SDR0_SDSTP0[NBW]: 0 : NDFC boot page selection -SDR0_SDSTP0[NBAC]: 0 : NDFC boot address selection cycle: 3 Addr. Cycles, 1 Col. + 2 Row (512 page size) -SDR0_SDSTP0[NARE]: 0 : NDFC auto read : disabled -SDR0_SDSTP0[NRB]: 0 : NDFC Ready/Busy : Ready -SDR0_SDSTP0[NDRSC]: 33333 : NDFC device reset counter -SDR0_SDSTP0[NCG0]: 0 : NDFC/EBC chip select gating CS0 : EBC -SDR0_SDSTP0[NCG1]: 0 : NDFC/EBC chip select gating CS1 : EBC -SDR0_SDSTP0[NCG2]: 0 : NDFC/EBC chip select gating CS2 : EBC -SDR0_SDSTP0[NCG3]: 0 : NDFC/EBC chip select gating CS3 : EBC -SDR0_SDSTP0[NCRDC]: 3333 : NDFC device read count - -PPC440EP Clocking Configuration - -SysClk is 33.0MHz, M is 20, VCO is 660.0MHz, CPU is 330.0MHz, PLB is 132.0MHz -OPB is 66.0MHz, EBC is 44.0MHz, MAL is 66.0MHz, Sync PCI is 66.0MHz - -The above information is reported by Eugene O'Brien -. Thanks a lot. - -2007-08-06, Stefan Roese ---------------------------------------------------------------------- - -The configuration for the AMCC 440EP eval board "Bamboo" was changed -to only use 384 kbytes of FLASH for the U-Boot image. This way the -redundant environment can be saved in the remaining 2 sectors of the -same flash chip. - -Caution: With an upgrade from an earlier U-Boot version the current -environment will be erased since the environment is now saved in -different sectors. By using the following command the environment can -be saved after upgrading the U-Boot image and *before* resetting the -board: - -setenv recover_env 'prot off FFF80000 FFF9FFFF;era FFF80000 FFF9FFFF;' \ - 'cp.b FFF60000 FFF80000 20000' - -2006-07-27, Stefan Roese -- cgit v1.2.3