From 8bde7f776c77b343aca29b8c7b58464d915ac245 Mon Sep 17 00:00:00 2001
From: wdenk <wdenk>
Date: Fri, 27 Jun 2003 21:31:46 +0000
Subject: * Code cleanup:   - remove trailing white space, trailing empty
 lines, C++ comments, etc.   - split cmd_boot.c (separate cmd_bdinfo.c and
 cmd_load.c)

* Patches by Kenneth Johansson, 25 Jun 2003:
  - major rework of command structure
    (work done mostly by Michal Cendrowski and Joakim Kristiansen)
---
 doc/README-i386 | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

(limited to 'doc/README-i386')

diff --git a/doc/README-i386 b/doc/README-i386
index 862f3f7a3a..02b753cbd7 100644
--- a/doc/README-i386
+++ b/doc/README-i386
@@ -4,23 +4,23 @@ work was sponsored by my emplyer, Omicron Ceti AB. http://www.omicron.se
 It is currently capable of booting a linux bzImage from flash on
 the AMD SC520 CDP platform.
 
-It was originally based on PPCBoot taken from the CVS October 28 2002.  
+It was originally based on PPCBoot taken from the CVS October 28 2002.
 
 To compile:
 
 1) Unpack the source tree, either from the complete tarball or
    from the virgin snapshot + the patch
-   
+
 2) Configure the source
    $ make sc520_cdp_comfig
    $ make
-   
+
 To use this code on the CDP:
 1) Make a suitable kernel, I used 2.4.19 with the mtd-support updated
    from the MTD CVS and a patch to allow root=/dev/mtdblock1 which I
-   included at the end of this file. 
+   included at the end of this file.
    The following options in the MTD section might be useful:
-   
+
    CONFIG_MTD_PHYSMAP=y
    CONFIG_MTD_PHYSMAP_START=38100000
    CONFIG_MTD_PHYSMAP_LEN=7a0000
@@ -29,9 +29,9 @@ To use this code on the CDP:
 
 2) Program it in to the CDP flashbank with remon
    u-boot.bin should be programmed att offset 0x7e000 and the kernel at
-   offset 0. If you want to use a jffs2 root file system (not included here), 
+   offset 0. If you want to use a jffs2 root file system (not included here),
    it should be  programmed to offset 0x100000.
-   
+
    remon> z
    remon> yi
    remon> ns u-boot.bin 7e0000
@@ -39,22 +39,21 @@ To use this code on the CDP:
    remon> ns image.jffs2 100000
 
 3) Connect a terminal to the 25pin serial port at 9600bps, and start the CDP.
-   
+
    remon> z
    remon> g
 
 4) U-Boot should output some message and a prompt on the terminal, to
    start the kernel issue the following command:
-   
+
    BOOT> bootm
-   
+
 5) The kernel should boot, and mount the root filesystem if present.
 
 We hope you find this stuff useful
 Daniel Engström, Omicron Ceti AB, daniel@omicron.se
 
 
-
 --- linux-2.4.19-orig/init/do_mounts.c	Sat Aug  3 02:39:46 2002
 +++ linux-2.4.19/init/do_mounts.c	Mon Sep 23 16:21:33 2002
 @@ -224,6 +224,14 @@
@@ -71,4 +70,5 @@ Daniel Engstr
 +	{ "mtdblock7", 0x1f07 },
  	{ NULL, 0 }
  };
- 
+
+-------------------
-- 
cgit v1.2.3