From c0def248caa5e2e6ed63249d3713830bd27e31e6 Mon Sep 17 00:00:00 2001 From: Chris Packham Date: Thu, 22 Sep 2016 12:56:14 +1200 Subject: arm: mvebu: add DB-88F6820-AMC board This board is a plug in card for Marvell's switch system development kits. Form-factor aside it is similar to the DB-88F6820-GP with the following differences. - TCLK is 200MHz - SPI1 is used - No SATA - No MMC - NAND flash Reviewed-by: Simon Glass Signed-off-by: Chris Packham Signed-off-by: Stefan Roese --- board/Marvell/db-88f6820-amc/MAINTAINERS | 6 ++ board/Marvell/db-88f6820-amc/Makefile | 7 ++ board/Marvell/db-88f6820-amc/db-88f6820-amc.c | 129 ++++++++++++++++++++++++++ board/Marvell/db-88f6820-amc/kwbimage.cfg | 12 +++ 4 files changed, 154 insertions(+) create mode 100644 board/Marvell/db-88f6820-amc/MAINTAINERS create mode 100644 board/Marvell/db-88f6820-amc/Makefile create mode 100644 board/Marvell/db-88f6820-amc/db-88f6820-amc.c create mode 100644 board/Marvell/db-88f6820-amc/kwbimage.cfg (limited to 'board') diff --git a/board/Marvell/db-88f6820-amc/MAINTAINERS b/board/Marvell/db-88f6820-amc/MAINTAINERS new file mode 100644 index 0000000000..abf5b7efdc --- /dev/null +++ b/board/Marvell/db-88f6820-amc/MAINTAINERS @@ -0,0 +1,6 @@ +DB_88F6820_AMC BOARD +M: Chris Packham +S: Maintained +F: board/Marvell/db-88f6820-amc/ +F: include/configs/db-88f6820-amc.h +F: configs/db-88f6820-amc_defconfig diff --git a/board/Marvell/db-88f6820-amc/Makefile b/board/Marvell/db-88f6820-amc/Makefile new file mode 100644 index 0000000000..79e1a75f4c --- /dev/null +++ b/board/Marvell/db-88f6820-amc/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (C) 2015 Stefan Roese +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := db-88f6820-amc.o diff --git a/board/Marvell/db-88f6820-amc/db-88f6820-amc.c b/board/Marvell/db-88f6820-amc/db-88f6820-amc.c new file mode 100644 index 0000000000..cade99c8d7 --- /dev/null +++ b/board/Marvell/db-88f6820-amc/db-88f6820-amc.c @@ -0,0 +1,129 @@ +/* + * Copyright (C) 2015 Stefan Roese + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h" +#include <../serdes/a38x/high_speed_env_spec.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define ETH_PHY_CTRL_REG 0 +#define ETH_PHY_CTRL_POWER_DOWN_BIT 11 +#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT) + +/* + * Those values and defines are taken from the Marvell U-Boot version + * "u-boot-2013.01-2016_T1.0.eng_drop_v10" + */ +#define DB_AMC_88F68XX_GPP_OUT_ENA_LOW \ + (~(BIT(29))) +#define DB_AMC_88F68XX_GPP_OUT_ENA_MID \ + (~(BIT(12) | BIT(17) | BIT(18) | BIT(20) | BIT(21))) +#define DB_AMC_88F68XX_GPP_OUT_VAL_LOW (BIT(29)) +#define DB_AMC_88F68XX_GPP_OUT_VAL_MID 0x0 +#define DB_AMC_88F68XX_GPP_OUT_VAL_HIGH 0x0 +#define DB_AMC_88F68XX_GPP_POL_LOW 0x0 +#define DB_AMC_88F68XX_GPP_POL_MID 0x0 + +static struct serdes_map board_serdes_map[] = { + {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, + {DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0} +}; + +int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) +{ + *serdes_map_array = board_serdes_map; + *count = ARRAY_SIZE(board_serdes_map); + return 0; +} + +/* + * Define the DDR layout / topology here in the board file. This will + * be used by the DDR3 init code in the SPL U-Boot version to configure + * the DDR3 controller. + */ +static struct hws_topology_map board_topology_map = { + 0x1, /* active interfaces */ + /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */ + { { { {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0} }, + SPEED_BIN_DDR_1866L, /* speed_bin */ + BUS_WIDTH_8, /* memory_width */ + MEM_4G, /* mem_size */ + DDR_FREQ_800, /* frequency */ + 0, 0, /* cas_l cas_wl */ + HWS_TEMP_LOW} }, /* temperature */ + 5, /* Num Of Bus Per Interface*/ + BUS_MASK_32BIT /* Busses mask */ +}; + +struct hws_topology_map *ddr3_get_topology_map(void) +{ + /* Return the board topology as defined in the board code */ + return &board_topology_map; +} + +int board_early_init_f(void) +{ + /* Configure MPP */ + writel(0x11111111, MVEBU_MPP_BASE + 0x00); + writel(0x11111111, MVEBU_MPP_BASE + 0x04); + writel(0x55066011, MVEBU_MPP_BASE + 0x08); + writel(0x05055550, MVEBU_MPP_BASE + 0x0c); + writel(0x05055555, MVEBU_MPP_BASE + 0x10); + writel(0x01106565, MVEBU_MPP_BASE + 0x14); + writel(0x40000000, MVEBU_MPP_BASE + 0x18); + writel(0x00004444, MVEBU_MPP_BASE + 0x1c); + + /* Set GPP Out value */ + writel(DB_AMC_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00); + writel(DB_AMC_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); + + /* Set GPP Polarity */ + writel(DB_AMC_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c); + writel(DB_AMC_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); + + /* Set GPP Out Enable */ + writel(DB_AMC_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04); + writel(DB_AMC_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); + + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + return 0; +} + +int checkboard(void) +{ + puts("Board: Marvell DB-88F6820-AMC\n"); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + cpu_eth_init(bis); /* Built in controller(s) come first */ + return pci_eth_init(bis); +} diff --git a/board/Marvell/db-88f6820-amc/kwbimage.cfg b/board/Marvell/db-88f6820-amc/kwbimage.cfg new file mode 100644 index 0000000000..1f748db37c --- /dev/null +++ b/board/Marvell/db-88f6820-amc/kwbimage.cfg @@ -0,0 +1,12 @@ +# +# Copyright (C) 2014 Stefan Roese +# + +# Armada XP uses version 1 image format +VERSION 1 + +# Boot Media configurations +BOOT_FROM spi + +# Binary Header (bin_hdr) with DDR3 training code +BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068 -- cgit v1.2.3