Age | Commit message (Collapse) | Author |
|
Synchronize initramfs related configuration options and improve
memory layout. The memory layout with an offset of 16MiB allows
to boot bigger kernels. With AUTO_ZRELADDR, which is pretty much
the standard nowadays, the kernel relacates itself to PC masked
with 0xf8000000 plus a text offset of 0x8000 (hence 0x80008000 for
Vybrid/i.MX 7 or 0x10008000 for i.MX 6). To avoid that the kernel
overwrites itself during uncompress, move the kernel further away
from its decompressed location. With a 16MiB offset from the start
of memory and a 16MiB distance to the device-tree, we allow kernel
up to ~16MiB.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
With the next release our update scripts write the kernel and
device tree in seperate UBI volumes. This allows to use a lot
less UBI/UBIFS support in U-Boot, which should lower the risk
of hitting bugs in this area.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Use the exact SoC information from the soc environment variable to
load the device tree file for the Colibri iMX7S or iMX7D.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
The command usb reset potentially requires to deregister USB keyboards,
hence enable it if USB Keyboards are enabled.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Enabled RDC (resource domain controller) to isolate peripherals between
the A7(s) and M4 core.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time.
There are 26 peripherals impacted by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is set M4 to a different domain with A core.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above to domain 0 only.
CM4 image will set the M4 to domain 1 only.
This patch enables the CONFIG_MXC_RDC for mx7d SABRESD board and ARM2 boards, and
setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
U-Boot on Apalis iMX6 has a known problem:
Apparently Apalis iMX6 does not works with Gigabit switches...
Limiting speed to 10/100Mbps, and setting master mode, seems to
be the only way to have a successful PHY auto negotiation.
How to fix: Understand why Linux kernel do not have this issue.
However, the current work around did not take effect since the
generic phy config function (which gets called after the board
level work-around) reenabled gigabit advertisment again.
Use the newly introduced environment variable to disable gigabit
Ethernet advertisement.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
With the next release our update scripts write the kernel and
device tree in seperate UBI volumes. This allows to use a lot
less UBI/UBIFS support in U-Boot, which should lower the risk
of hitting bugs in this area. Boot times are also slightly
faster (measurements showed an improvement of ~150ms).
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Implement optional PCIe EvalBoard initialisation which properly reset the PLX
(now Avago) PEX 8605 PCIe switch plus PCIe devices on the Apalis Evaluation
carrier board.
Please note that you will have to enable the second PCIe port in the dts as well
e.g.:
diff --git a/arch/arm/dts/tegra30-apalis.dts b/arch/arm/dts/tegra30-apalis.dts
index be4f4d6..321c7d6 100644
--- a/arch/arm/dts/tegra30-apalis.dts
+++ b/arch/arm/dts/tegra30-apalis.dts
@@ -59,6 +59,7 @@
};
pci@2,0 {
+ status = "okay";
nvidia,num-lanes = <1>;
};
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Get rid of the noatime mount option as L4T resp. Ubuntu does not seem to like
that one at all and rather fails booting as follows:
* Starting NVIDIA specific init script [fail]
...
* Starting NSM status monitor [ OK ]
The disk drive for / is not ready yet or not present.
keys:Continue to wait, or Press S to skip mounting or M for manual recovery
* Starting NSM status monitor [ OK ]
...
* Starting NSM status monitor [fail]
* Stopping NSM status monitor [ OK ]
* Starting Bridge socket events into upstart [ OK ]
The mount now defaults to relatime.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Configure the Ricoh PMIC RN5T567 at startup to reset the board
without delay.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add power driver for Ricoh PMIC used on Colibri iMX7.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
With the next release our update scripts write the kernel and
device tree in seperate UBI volumes. This allows to use a lot
less UBI/UBIFS support in U-Boot, which should lower the risk
of hitting bugs in this area. Boot times are also slightly
faster (measurements showed an improvement of ~150ms).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
As we now have the configblock handling the MAC address is set
from the configblock.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
This lives now in colibri_imx7_defconfig
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Code mostly ported from imx-kobs-5.3.
MTD partitioning is set accordingly.
writebcb: Write Boot Control Block (FCB and DBBT)
writeboot: Write bootloadder
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
kobs-ng needs a partition which holds FCB, DBBT, and Bootloader,
not FCB, DBBT alone.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Use get_ram_size() to autodetect up to 2Gbyte of RAM on rank 0.
If chips with two ranks would get stuffed one would have to set the size
of one rank in DDRC_ADDRMAP0.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Introduce CONFIG_SERIAL_TAG_BOARD which removes the definition of
void get_board_serial(struct tag_serialnr *serialnr)
in order to allow its definition in board specific code.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
This reverts commit e7d4767331f1a2cbef61b4e89beb73731f267499.
|
|
The current 36M offset will conflict with NAND FCB firmware2 when the
nand chip block is 1MB size. This patch change it to 36M + 1M offset,
so the redundant u-boot at firmware2 will not be broken.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Same issue as ENGR00321137, commit 3695635.
GIS module need total 3M+3M+1.5M+1.5M=9M video memory.
and sys reserved 16M memory for malloc.
When gis module enabled, malloc may failed to allocate memory
for other modules, that may cause system hang.
Expand malloc pool to 32M.
Signed-off-by: Sandor Yu <R01008@freescale.com>
|
|
The previous 8M address for NAND env might conflict with other boot
parameters as the NAND block size increasing, change it to 36M to avoid
it.
Signed-off-by: Han Xu <b45815@freescale.com>
|
|
enlarge the maximum nand page size and oob size to
16k byte and 1280byte.
Signed-off-by: Han Xu <b45815@freescale.com>
|
|
The actual memory size is 256MB not 512MB, otherwise it has a wrap
problem in memory and will cause memtester failed.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Since the mx6ul 9x9 evk has different DDR size with 14x14 evk, change
to use the half of PHYS_SDRAM_SIZE for mtest end.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Add i.MX6QP SabreSD board support.
Signed-off-by: Anson Huang <b20788@freescale.com>
|
|
Need to check fuse bit 25 of bank 0 word 4 before initialize bee.
The bit: 0 means bee enabled, 1 means bee disabled.
If disabled, continuing initialize bee will cause system hang, so
need to check this bit before initialize bee.
Add macro to enable BEE in header file, default disabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
i.MX6UL-9x9-EVK board has PFUZE3000, so enable LDO
bypass support for this board.
Signed-off-by: Anson Huang <b20788@freescale.com>
|
|
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time.
There are 26 peripherals impacted by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is set M4 to a different domain with A core.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above to domain 0 only.
CM4 image will set the M4 to domain 1 only.
This patch enables the CONFIG_MXC_RDC for mx7d SABRESD board and ARM2 boards, and
setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
This mx7d 19x19 lpddr2 arm2 board is based on 19x19 lpddr3 arm2 board
with DDR changed to 512M LPDDR2. We added DDR script for LPDDR2 and
a new u-boot build target: mx7d_19x19_lpddr2_arm2_config
LPDDR2 script source: lpddr2_0_1.ds
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Since the i.MX6ul 9x9 evk board only has 256MB LPDDR2, while the
CMA size used in kernel configuration is 320MB, so we have to set
another value for the 9x9 evk board.
This patch sets the cma=96M bootargs to in uboot. So the kernel will
overwrite to use the new value.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
The i.mx6ul 9x9 EVK shares the same base board with 6ul 14x14 EVK
with two main changes on CPU board:
1. Change to use pfuze 3000.
2. Use 256MB LPDDR2 memory.
This patch uses a macro CONFIG_6UL_9X9_LPDDR2 to distinguish the changes above,
basing on 14x14 EVK board level codes.
The new build target for the 9x9 EVK: mx6ul_9x9_evk_config
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
As we need to support LPSR mode resume and due to hardware
design requirement, DCD can NOT put DRAM exit from retention
mode, so only plug in mode can do that to support LPSR mode,
so enabled plug in mode by default for imx7d 12x12-lpddr3-arm2
board.
Signed-off-by: Anson Huang <b20788@freescale.com>
|
|
Since setup_waveform_file in different boards code have same implementation,
move setup_waveform_file to board common code. Also rename it to
board_setup_waveform_file
This patch also fix a bug when using flush_cache. We should pass
'waveform_buf' to flush_cache, but not a string named 'addr'.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
Support draw image on E-ink screen.
1. The image format should be PGM-P5 raw data format.
2. The image should be named epdc_logo.pgm.
3. If no epdc_logo.pgm found in the first partition(FAT), will choose
to draw black border on the screen.
4. Default configuration is to draw image at pos (0,0). If 'splashpos'
env is set, will choose the pos from 'splashpos'.
5. The image size should not be bigger than screen total pixel size.
6. Implement board_setup_logo_file in board/freescale/common/epdc_setup.c
7. Introudce function prototype for board_setup_logo_file.
Note: i.MX7D EPDC supports advanced mode and standard mode. Since current
PXP in uboot for i.MX7D not ready, only support standard mode now.
advanced and standard mode needs waveform firmware's support.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
Enable fastboot command "fastboot flash data"
Custom may need to update data partition in fastboot mode.
This patch enable flash data partition in emmc\sd.
Signed-off-by: Zhang Sanshan <b51434@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
1. Replace the UDC driver with community's USB gadget d_dnl driver.
2. Integrate the FSL SD/SATA/NAND flash operations, since the GPT and
EFI partitions are not support by i.MX.
3. Add FDT support to community's android image.
4. Change the booti command to boota, due to the booti has been used for
ARM64 image boot.
5. Modify boota implementation to load ramdisk and fdt to their loading
addresses specified in boot.img header, while bootm won't do it for
android image.
6. Modify the android image HAB implementation. Authenticate the boot.img
on the "load_addr" for both SD and NAND.
7. Enable new configuration CONFIG_FSL_FASTBOOT for Freescale's fastboot
with relevant header file "fsl_fastboot.h". While disabling the
configuration, the community fastboot is used.
8. Use community's way to combine cmdline in boot.img and u-boot environment,
not overwrite the cmdline in boot.img
Signed-off-by: Ye.Li <B37916@freescale.com>
|