summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2014-11-13Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-11-13zynq: zybo: Move CONFIG_DEFAULT_DEVICE_TREE to defconfigMichal Simek
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Move CONFIG_DEFAULT_DEVICE_TREE from board config directly to defconfig. This patch removes compilation warning: include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE" redefined [enabled by default] #define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-13Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini
2014-11-12powerpc: remove orphaned boards mcc200 and prs200Nikita Kiryanov
mcc200 and prs200 are old and have no maintainer. Remove the boards. This also removes the mcc200 specific 1bpp BMP support from common/lcd.c Cc: Wolfgang Denk <wd@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-11-12km_arm: convert the km_arm boards to the generic board supportValentin Longchamp
This implies that all the km_kirkwood boards and their variants now are using the generic board init sequence. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2014-11-12ARM: UniPhier: call pin_init() also in the normal bootMasahiro Yamada
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and it is defined in ./.config but not in spl/.config, so pin_init() should be called from the normal image so that UART works correctly. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: decrease pre-reloc malloc area sizeMasahiro Yamada
In the current implementation of the boot sequence of UniPhier platform, 32KB temporary RAM is available before relocation. The malloc area and the stack shares the 32KB area. With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB) is left for the stack. In some use cases, the system hangs up with stack over-flow. Even with driver-model UART enabled, the malloc area of 0x2000 (8KB) should be enough. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: enable USB featuresMasahiro Yamada
FAT-formated USB storage device access is available. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: move DDR related configuration to KconfigMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-11configs: zynq: Add config support for ZYBOTinghui Wang
This patch adds config support needed for ZYBO target and has been tested on Rev. B ZYBO hardware. Signed-off-by: Tinghui Wang <steven.wang@digilentinc.com> [PC changes: * Dropped boards.cfg change (rebase conflict) * Dropped custom u-boot env * Added DTS * Misc forward-porting changes ] Signed-off-by: Peter Crosthwiate <crosthwaite.peter@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-10Merge branch 'master' of git://git.denx.de/u-boot-blackfinTom Rini
2014-11-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-11-10bfin: the max bfin sdh block count is 127Sonic Zhang
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-11-07powerpc: o2dnt: convert to generic boardAnatolij Gustschin
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2014-11-07Merge git://git.denx.de/u-boot-tiTom Rini
2014-11-07usb: include <asm/cache.h> and <part.h> from include/usb.hMasahiro Yamada
The header file include/usb.h references ARCH_DMA_MINALIGH and block_dev_desc_t, thus it must include <asm/cache.h> and <part.h>. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-07arm: socfpga: Add example UDC configMarek Vasut
Add example of an USB UDC configuration with DFU and UMS. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Vince Bridgers <vbridger@altera.com> Acked-by: Pavel Machek <pavel@denx.de> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2014-11-07usb: s3c-otg: Allow custom gusbcfgMarek Vasut
Allow passing in a custom configuration of the gusbcfg register via platform data. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Vince Bridgers <vbridger@altera.com> Acked-by: Pavel Machek <pavel@denx.de> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2014-11-07usb: s3c-otg: Split out PHY controlMarek Vasut
Split the Samsung specific PHY control into a separate file and compile this into the S3C OTG driver only if used on a Samsung system. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Vince Bridgers <vbridger@altera.com> Acked-by: Pavel Machek <pavel@denx.de> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2014-11-07arm: socfpga: Add DT support for SoCFPGA and add socfpga_socrates targetStefan Roese
This patch includes the latest DT sources for socfpga from the current Linux kernel. And enables CONFIG_OF_CONTROL for the new build target "socfpga_socrates" (the EBV SoCrates board) to make use of this new DT support. Until this patch, the only SoCFPGA U-Boot target in mainline is "socfpga_cyclone5". This build target is not (yet) changed to support DT. So nothing changes for this target. Even though the long-term goal should be to move all SoCFPGA targets over to DT. One of the reasons to enable DT support in SoCFPGA is, that I need to support multiple different SPI controllers for this platform. This is the QSPI Cadence controller and the Designware SPI master controller. Both are implemented in the SoCFPGA. And enabling both controllers is only possible by using the new driver model (DM). The DM SPI code only supports DT based probing. So it was easier to move SoCFPGA to DT than to add the (deprecated) platform-data based probing to the DM SPI suport. Note that the image with the dtb embedded is u-boot-dtb.img. This needs to be used now for those DT enabled boards instead of u-boot.img. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Vince Bridgers <vbridger@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Pavel Machek <pavel@denx.de> Cc: Simon Glass <sjg@chromium.org>
2014-11-07socfpga_cyclone5.h: fix kernel console argument in default environmentAnatolij Gustschin
With fresh environment the kernel gets wrong console argument and boots without console output. Fix it. Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Marek Vasut <marex@denx.de>
2014-11-06omap3: cm-t3517: add LCD/DVI and splash supportIgor Grinberg
Add support for splash screen on both DVI and SCF0403 LCD. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06omap3: cm-t3517: add Ethernet supportIgor Grinberg
Add both EMAC and SMC911x support. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06omap3: cm-t3517: add USB supportIgor Grinberg
Add both host and mUSB support. Currently, the selection between host USB and mUSB is done through the config file. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06omap3: cm-t3517: add basic board supportIgor Grinberg
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC. Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT, Analog audio codec, touch screen controller, LED. Add basic support including: LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2014-11-06ks2_evm: config: enable fatload commandKhoronzhuk, Ivan
The keystone2 evm can boot from USB partition with FAT32 FS, so enable generic load command and fatload command usage. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06keystone2: config: align names of images with MCSDKKhoronzhuk, Ivan
The Multicore Software Development Kit (MCSDK) provides foundational software for TI KeyStone II device platforms. It's supposed to be used with uboot, and it's convenient to have the same names for images, so correct environment image names according to the last MCSDK3. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06keystone2: config: restructure handling of default env settingsMurali Karicheri
Currently to customize env for various ks2 boards, individual variables such as NAME_FS etc are defined and included in the common config.h to define CONFIG_EXTRA_ENV_SETTINGS. This doesn't scale well if a variable is not applicable on a specific board. Using this scheme, we have to define variables with empty value and it's ugly. Instead, to allow board specific customization of default env variable, define a common CONFIG_EXTRA_ENV_KS2_SETTINGS for all common variables and define board specific variables in individual board specific config.h using CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS. Use the common and board specific variables to define CONFIG_EXTRA_ENV_SETTINGS. This way more variables can be added in future for individual boards without affecting the other config.h files. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06keystone2: change default boot mode to ubiMurali Karicheri
To allow out of box demo, change default boot mode to ubi boot now that NAND is functional in latest EVMs. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06ks2_evm: configs: fix UBI volume nameKhoronzhuk, Ivan
The UBI volume name has to be prefixed with "ubi:". Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06ARM: TI: omap3: remove raw initrd support in omap3_igep00x0 config file ↵Guillaume GARDET
since it is now in ti_armv7_common.h Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06ARM: TI: Enable raw initrd supportGuillaume GARDET
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-05Merge branch 'rmobile' of git://www.denx.de/git/u-boot-shTom Rini
2014-11-05board: k2l_evm: add network supportHao Zhang
This patch adds network support code and enables keystone_net driver usage for k2l_evm evaluation board. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-11-05net: keystone_serdes: add keystone K2L SoC supportKhoronzhuk, Ivan
Keystone2 Lamar SoC uses the same keystone SerDes driver. All Keystone2 EVM boards currently use SerDes driver, so move CONFIG_TI_KEYSTONE_SERDES to common configuration file. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-11-05Enable Android Fastboot support on am335x_evm boardDileep Katta
Signed-off-by: Dileep Katta <dileep.katta@linaro.org> [trini: Rework so that am335x_evm_usbspl still builds] Signed-off-by: Tom Rini <trini@ti.com>
2014-11-05Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2014-11-05twl4030: More voltages on VAUX2 and VAUX3Paul Kocialkowski
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2014-11-05dm: sunxi: Add support for serial using driver modelSimon Glass
Add a driver for the designware serial UART used on sunxi. This just redirects to the normal ns16550 driver. Add a stdout-path to the device tree so that the correct UART is chosen. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05dm: sunxi: Modify the GPIO driver to support driver modelSimon Glass
This adds driver model support to the sunxi GPIO driver, using the device tree to trigger binding of the driver. The driver will still operate without driver model too. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05dm: sunxi: Add a new config for an FDT-based pcDuino3Simon Glass
For now we won't want to mess with the existing configurations. Create a new one which will enable device tree and driver model. Note that this brings the device tree binary into u-boot-sunxi-with-spl.bin. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05dm: sunxi: dts: Add sun7i device tree filesSimon Glass
These are from Linux 3.17-rc7 (commit fe82dcec). U-Boot only uses a small portion of these, but we may as well have something to look forward to. The total compiled size is about 25KB. Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05sunxi: Use CONFIG_MACH_SUN?I from Kconfig instead of CONFIG_SUN?IIan Campbell
Mostly automatic with: sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I) followed by removing the relevant #defines from include/configs/sun?i.h by hand. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04serial: add prototypes for init functionsJeroen Hofstee
While at it, sort them. Cc: Tom Rini <trini@ti.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-11-04Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingTom Rini
2014-11-04usb: Make pollable int support available outside of ehci-hcd.cHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04arm: rmobile: alt: Add VFAT filesystem supportNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-04arm: rmobile: alt: Add support USB and USB commandsNobuhiro Iwamatsu
This adds support for USB commands and USB storage device. Signed-off-by: Yoshiyuki Ito <yoshiyuki.ito.ub@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-08 11:20:33 +0000