Age | Commit message (Collapse) | Author |
|
with the changes introduced for 3517 support, compilation
for omap3evm breaks. this patch addresses the dependencies
|
|
Increased the bootargs buffer size to 512 for both omap3/3517.
|
|
Fixes for setting CAN_STB line to low to enable CAN
transceiver; typo fixes for HECC TX/RX padconfig names
Signed-off-by: Anant Gole <anantgole@ti.com>
|
|
Do not enable clocks for those modules not present
on OMAP3505/17.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
|
|
Some initialization like, Pad configuration, clock settings
needs to be done from U-Boot for MMC2 port
to be accessed from Kernel.
Please note that u-boot still only supports MMC1 Port. To enable MMC2
from U-Boot one should only change the BASE address and it should work.
|
|
Changes -
- Makefile : omap3517evm_config => omap3517_evm_config
- omap3517evm.h => omap3517_evm.h
|
|
|
|
Pulled up from branch omap-uboot-denx/int_030000_evm_bringup.
|
|
U-Boot was printing DDR size as 0, as of now hard-coded it with
macro (defined in include/configs/omap3517evm.h).
TODO:
- Ideally it should calculate the size baded on EMIF configuration
made by primary bootloader (x-loader).
|
|
OMAP3517 Pre-Alpha board is a development platform
used before actual OMAP3517EVM board, below are the details -
Validation -
- PLL conifguration
- NAND 16-bit micron part (x-loader, u-boot, Linux)
- MMC1 (x-loader, u-boot, Linux)
- Video (LCD (4.3" Sharp part))
- Complete NAND boot mode
- Complete MMC boot mode
Changes -
- GPMC Timing parameters for NAND interface
- UART3 made as serial console
Issues -
- Clock init code still need to be cleaned up.
- boot config code needs to changed for supporting both mmc and nand
boot
|
|
OMAP3517TEB board is being used as a pre-silicon development
platform, below are the details -
Validation -
- PLL conifguration
- NAND 8-bit micron part (x-loader, u-boot)
- USB Host* (Linux)
- MMC1 (x-loader, u-boot, Linux)
- Video (TV out, LCD (Toshiba part))
- MMC boot from x-loader
Changes -
- GPMC timing parameters for NAND interface
- omap3517evm.h config file cleanup
- commented out "smi" instruction
Issues -
- USB host support has been validated by commenting the
mux configuration in u-boot. Was not able to conclude on
muxing part of it.
- NAND 16-bit is not working, found out to be daughter card issue
Daughter card is not designed for 16bit micron part.
- LCD is validated based on AVV panel initialization, since it was SPI
based LCD panel.
|
|
Added support for OMAP3517/3505 SoC, it includes all the changes
from Mani's commit for OMAP3517 and review comments fix.
Major features/changes -
- New config file
- New board files
- New ethernet driver
Major Review comments -
- Added macine ID for OMAP3517
- Naming conventions used.
|
|
Clean up macros and comments.
|
|
|
|
Total5200 and digsy MTC use I2C port 2 pins as a ATA chip select.
To avoid adding board-specific ifdefs to cpu/mpc5xxx/ide.c new
define CONFIG_SYS_ATA_CS_ON_I2C2 was introduced. It is used by
Total5200 and will be used by digsy MTC and other boards with
ATA CS on I2C pins.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
|
|
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
renaming the "mgsuvd" board port into "km8xx", because
there come more similar boards from keymile.
Compiling the mgsuvd board with "make mgsuvd_config"
remains.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
- added to keymile-common.h:
- bootcount support
- COMMAND HISTORY
- CONFIG_AUTO_COMPLETE
- CONFIG_SYS_FLASH_PROTECTION
- JFFS2 support
- CONFIG_VERSION_VARIABLE
- extracted common I2C settings for all boards
- common default environment settings summarized
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
with the new CONFIG_SYS_DELAYED_ICACHE config option, ICache
is not enabled before code runs from RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Size of one environment sector is 0x20000.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Fix indentation broken by symbol renames. "Sort" driver related definitons.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
|
|
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Default gzip bootm size is 8MB. Some platforms require
more than 8MB
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
|
|
Read and store OMAP3 die ID in U-Boot environment.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
The rtl8139 driver use pci_mem_to_phys. So it need PCI system memory
registration.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Some register value was hardcoded for System memory size 128MB and
memory offset 0x08000000. This patch fixed the problem.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This adds tsec12ioovcr to include/asm-ppc/immap_85xx.h (was reserved.)
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
|
|
Conflicts:
lib_ppc/board.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
- HRCW update
HRCWH_BOOTSEQ_DISABLE not HRCWH_BOOTSEQ_NORMAL
HRCWH_LALE_EARLY added
- DDR-SDRAM settings modified. This solves sporadically
problems with this memory.
- CS1 now 128 MB window size
- CS3 now 512 MB window size
- PRAM activated
- MTDPARTS_DEFAULT defined
- CONFIG_HOSTNAME added
- MONITOR_LEN now 384 KB
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch adds I2C support for the Keymile kmeter1 board.
It uses the First I2C Controller from the CPU, for
accessing 4 temperature sensors, an eeprom with IVM data
and the booteeprom over a pca9547 mux.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The previous version rebooted forever with DDR bigger than 256MB.
Access the DS1339 RTC chip is on I2C1 bus.
Allow DHCP.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
The "eet" variant of the imx31_phycore board has an OLED display, using a
s6e63d6 display controller on the first SPI interface, using GPIO57 as a
chip-select for it. With this configuration you can display 256 colour BMP
images in 16-bit RGB (RGB565) LCD mode.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This patch also simplifies some ifdefs in lcd.c, introduces a generic
vidinfo_t, which new drivers are encouraged to use and old drivers to switch
over to.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
This is a driver for the S6E63D6 SPI OLED display controller from Samsung.
It only provides access to controller's registers so the client can freely
configure it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
This is a minimal driver, so far only managing output. It will
be used by the mxc_spi.c driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This is just a handy routine that reports last PCI busno: we walk
down all the hoses and return last hose's last_busno.
Will be used by PCI/PCIe initialization code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Currently, we get 256MB as the default, but since all the 86xx
board configs define a 2G BAT mapping for RAM, raise default
to 2G.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
NetLoop polls every cycle with getenv some environment variables.
This is horribly slow, especially when the environment is big.
This patch reads only the environment variables in NetLoop,
when they were changed.
Also moved the init part of the NetLoop function in a seperate
function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The file was generated from building versatile_defconfig.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|