| Age | Commit message (Collapse) | Author |
|---|
|
Prevent further viral propogation of the unused
symbol CONFIG_L1_INIT_RAM by just removing it.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Introducing 64-bit (36-bit) support for the MPC8641HPCN
failed to accomodate the other two 86xx boards.
Introduce definitions for CONFIG_SYS_CCSRBAR_PHYS_{LOW,HIGH}
CONFIG_SYS_CCSR_DEFAULT_DBAT{U,L} and CONFIG_SYS_CCSR_DEFAULT_IBAT{U,L}
with nominal 32-bit values.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
|
|
|
|
|
|
|
|
This patch disables some unused features from the PCI405 configuration
to keep U-Boot image size below 192k.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch fix the broken boot from NOR Flash on AT91RM9200 boards, if
CONFIG_AT91RM9200 is defined and nor preloader is used.
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
|
|
This patch enables support for EXT2, and increases the
CONFIG_SYS_BOOTMAPSZ size for the default configuration
of the katmai boards to use them as the RAID-reference
AMCC setups.
EXT2 enabling allows one to boot kernels from the EXT2
formatted Compact Flash cards.
CONFIG_SYS_BOOTMAPSZ increasing allows one to boot the
Linux kernels, which use PAGE_SIZE of 256KB. Otherwise,
the memory area with DTB file (which is placed at the
end of the bootmap area) will turn out to be overlapped
with the BSS segment of the 256KB kernel, and zeroed
in early_init() of Linux.
Actually, increasing of the bootmap size could be done
via setting of the bootm_size U-Boot variable, but it looks
like the current U-Boot implementation have some bootm_size-
related functionality lost. In many places through the U-Boot
code the CONFIG_SYS_BOOTMAPSZ definition is used directly
(instead of trying to read the corresponding value from the
environment). The same is truth for the boot_jump_linux()
function in lib_ppc/bootm.c, where U-Boot transfers control
to Linux passing the CONFIG_SYS_BOOTMAPSZ (not bootm_size)
value to the booting kernel.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Expanded OCM TLB to allow access to 64K OCM as well as 256K of
internal SRAM.
Adjusted internal SRAM initialization to match updated user
manual recommendation.
OCM & ISRAM are now mapped as follows:
physical virtual size
ISRAM 0x4_0000_0000 0xE300_0000 256k
OCM 0x4_0004_0000 0xE304_0000 64k
A single TLB was used for this mapping.
Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
At least some (old ?) versions of the AT91Bootstrap do not set up the
PLLB correctly to 48 MHz in order to make USB host function correctly.
This patch sets up the PLLB to the same values Linux uses, and makes USB
work ok on the following CPUs:
- AT91CAP9
- AT91SAM9260
- AT91SAM9263
This patch also defines CONFIG_USB_STORAGE and CONFIG_CMD_FAT for all
the relevant AT91CAP9/AT91SAM9 atmel boards.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Introduce AT91_CPU_CLOCK and use it for displaying the CPU
speed in the LCD driver.
Also make AT91_MAIN_CLOCK and AT91_MASTER_CLOCK reflect the
corresponding board clocks.
Signed-off-by: Stelian Pop <stelian@popies.net>
|
|
modify the CAS timings. my understanding is that these
settings decrease various wait times in the DDR interface.
Because these wait times are in clock cycles, and the DDR
clock on the 8315 RDB runs slower than on some other 83xx
platforms, we can dial down these values without a problem,
thereby decreasing the latency of memory a little.
Signed-off-by: Howard Gregory <Greg.Howard@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
To enable UBI on Apollon you need to uncomment the CONFIG_SYS_USE_UBI
macro.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
Since we've changed the memory map of the board, be nice and
add some checking to try to catch out-of-date .dts files. We do
this by checking the CCSRBAR location in the .dts and comparing
it to the CCSRBAR location in u-boot. If they don't match, a
warning msg is printed. This isn't foolproof, but it's simple and
will catch most of the cases where an out-of-date .dts is present,
including all of the cases where a new u-boot is used with an old
standard MPC8641 .dts file as supplied with Linux.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
We define CONFIG_MONITOR_BASE_EARLY to define the initial location
of the bootpage in flash. Use this to create an early mapping
definition for the FLASH, and change the early_bats code to use this.
This change facilitates the relocation of the flash since the early
mappings are no longer tied to the final location of the flash.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
Currently, that's what it is, but it's hardcoded.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
There's a lot of setup and foo for the second flash
bank. The problem is, this board doesn't actually have one.
Clean this up. Also, the flash is 8M in size. Get rid
of the confusing aliased overmapping, and just map 8M.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
It's currently defined twice inside in an if/else block, but
both halves set the same value. Move the define outside
the if.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
|
|
All in-tree IBM/AMCC PPC4xx boards using the EMAC get this new CONFIG
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
|
|
We put the bootpg for the secondary cpus into memory and use
BPTR to get to it. This is a step towards converting to the
ePAPR boot methodology. Also, the code is written to
deal properly with more than 4GB of RAM.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
There are several items in the config file that were hardcoded
but that should really be based on other config options, since
the regions are contiguous and depend on being so. This cleans
that up a bit. Also, add BR_PHYS_ADDR() macro to convert
addresses into the proper format for BR registers.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
Currently, the CCSR gets relocated while translation is
enabled, meaning we need 2 BAT translations to get to both the
old location and the new location. Also, the DEFAULT
CCSR location has a dependency on the BAT that maps the
FLASH region. Moving the relocation removes this unnecessary
dependency. This makes it easier and more intutive to
modify the board's memory map.
Swap BATs 3 and 4 on 8610 so that all 86xx boards use the same
BAT for CCSR space.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
You can't actually have both, and with some coming changes to
change the memory map for the board and support 36-bit physical,
we need the extra BAT that is being consumed by having both.
I also make non-PCI configs build cleanly, for the sake of sanity.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
We don't actually ever do this, remove the code so we
can stop maintaining it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Add serial boot support
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Consolidate ATA, ePORT, QSPI, FlexCan, PWM, RNG,
MDHA, SKHA, INTC, and FlexBus structures and
definitions in immap_5xxx.h to more unify modules
header files. Append DSPI support for m547x_8x.
SSI cleanup. Remove USB Host structure from immap_539.h.
Apply changes to use FlexBus structures in mcf52x2's
cpu_init.c and platform configuration files.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
This patch defines 1M TLB&LAW size for NAND on MPC8536DS, assigns 0xffa00000
for CONFIG_SYS_NAND_BASE and adds other NAND supports in config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image.
Singed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
CONFIG_ENV_ADDR should be (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE).
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Xilinx ppc440 and ppc405 have many similarities. This patch merge the
config files of both infrastuctures
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO
pin multiplexing correctly
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
Converted MPC8610HCPD, MPC8641HPCN, and SBC8641D to use
fsl_pci_setup_inbound_windows() and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
|
