Age | Commit message (Collapse) | Author |
|
1. The SPL's length of SDCARD boot has not enough,expand the SPL's
length to 128K.
2. deleted unused symbol: CONFIG_SYS_RUN_INDDR
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.
T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
- Two on-board 10M/100M/1G bps RGMII ports
- Two 10Gbps XFI with on-board SFP+ cage
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
- Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
- 8 lanes up to 10.3125GHz
- Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
- 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
- Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
voltage translators
- I2C:
- Four I2C controllers.
- UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Now that the designware ethernet driver uses phylib we need to turn it
on here.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
AXS101 is a new generation of devlopment boards from Synopsys that houses
ASIC with ARC700 and lots of DesignWare peripherals:
* DW APB UART
* DW Mobile Storage (MMC/SD)
* DW I2C
* DW GMAC
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
Arcangel4 is a FPGA-based development board that is used for prototyping and
verificationof of both ARC hardware (CPUs) and software running upon CPU.
This board avaialble in 2 flavours:
* Little-endian (arcangel4)
* Big-endian (arcangel4-be)
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
|
|
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
It speeds up writing a lot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The new prototype and the final series was moved from Micron to Spansion
to have a better reset sequence that is easier to support.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This define can be used if the ubi boot partition (defined for all
Keymile boards with KM_UBI_PARTITION_NAME_BOOT #define to ubi0) needs
some additionnal boot options.
This is the case for the kmp204x boards since u-boot does not support
NAND Flash subpage accesses on this platform, an additionnal argument
that defines the VID offstet must be given to the kernel.
The UBI cmd line option now looks like this "ubi.mtd=ubi0,2048" on this
platform.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to boards.cfg to keep targets in order]
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.
The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
- SCL = GPIOA_20
- SDA = GPIOA_21
The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
This covers only non-L2 switch ethernet interfaces i.e.
RGMII and SGMII interface for both T1040RDB and T1042RDB_PI
T1040RDB is configured as serdes protocol 0x66 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
1 SGMII on DTSEC3
T1042RDB_PI is configured as serdes protocol 0x06 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change in commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Add usb2 node entry to hwconfig default
Remove DDR controller interleaving from hwconfig
Move SPI related macros out of "#ifdef CONFIG_SPIFLASH"
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible in u-boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Fix commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Add usb2 node entry in "hwconfig string"
Remove controller interleaving from hwconfig string as T1040
has only one DDR conroller
SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
are move outside so that they are defined for all cases as these
macros are also used by other u-boot code
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5
Define MDIO related configs
Added eth.c file
Update t1040.c to support RGMII and SGMII
Update t1040qds.c to support ethernet
Define the PHY address
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: remove dash from commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Add the USB host boot support for the am43xx evm
Add the macros to boot from a usb drive in uBoot
Signed-off-by: Dan Murphy <dmurphy@ti.com>
|
|
We do not have to define CONFIG_MPC5xxx in board config headers
(and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk
because all target boards with mpc86xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
We do not have to define CONFIG_MPC824X in board config headers
because it is defined in arch/powerpc/cpu/mpc824x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
We do not have to define CONFIG_MPC512X in board config headers
because it is defined in arch/powerpc/cpu/mpc512x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
We do not have to define CONFIG_MPC83xx in board config headers
because it is defined in arch/powerpc/cpu/mpc83xx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
We do not have to define CONFIG_4xx in board config headers
because it is defined in arch/powerpc/cpu/ppc4xx/config.mk.
include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx".
I believe it is a typo because "CONFIG_4x" is not used at all
in other files.
So, I also deleted "CONFIG_4x" in include/configs/JSE.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Like other architectures, CONFIG_AVR32 can be defined
in arch/avr32/config.mk rather than board header files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.
This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
linker error.
So, Increase the u-boot binary size to 768KB.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG.
Also add their details in README.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Using the TPL/SPL method to booting from 8k page NAND flash.
- Add 256kB size SRAM tlb for second step booting;
- Add spl.c for TPL image boot;
- Add spl_minimal.c for minimal SPL image;
- Add C29XPCIE_NAND configure;
- Modify C29XPCIE.h for nand config and enviroment;
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Update following DDR related settings for T1040QDS
-Correct number of chip selects to two as t1040qds supports
two Chip selects.
-Update board_specific_parameters udimm structure with settings
derived via calibration.
-Reduced I2C speed to 50KHz as DDR-SPD does not get reliably
read at 400KHz.
Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 833MT/s, 1333MT/s and
1600MT/s.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
findftd is currently setting fdtfile to undefined for the beagle c4, select omap3-beagle.dtb instead
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
|
|
This patch enables ethernet support in ARMv8 foundation model. The ARMv8
foundation model supports a SMSC91C111 integrated MAC and PHY module
which is present at base address 0x01A000000.
The previous implementation had enabled SMSC9115 ethernet controller
which is not present on the ARMv8 foundation model.
Tested on ARMv8 foundation model v1 and v2 by running ping/tftp
between the foundation model and the host PC via a bridged network.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
|
|
Provide default Poll Timeout value for Trats2 board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Disable L2 caches for Trats and Trats2 devices.
It turns out that for data downloading with thordown command L2 cache
disablement brings a significant speed improvement.
rootfs - 400 MiB:
- L2 cache enabled: 2.69 MiB/s
- L2 cache disabled: 5.56 MiB/s
Such improvement is possible due to reduction of the need to invalidate
redundant data, which resides in L2 cache.
Since the sent USB request size at once is 512B (L1 - 32 KiB in total) -
one can be quite confident that it is already available in L1 and L2 can
be disabled.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch adds extra dfu_alt_info entries to support storing the whole BOOT
, DATA and UMS partitions.
This allows upgrade of uImage and device tree blob (dtb) files at once.
Now it is also possible to store ext4 rootfs prepared with well established
linux tools (like mkfs.ext4).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
|
|
This supports SH-QSPI device on koelsch board, and enable booting from
SPI flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This supports SH-QSPI device on lager board, and enable booting from
SPI flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
SolidRun has designed the Hummingboard board based on mx6q/dl/solo.
Add the initial support for the mx6 solo variant.
More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware
(Carrier-One was the previous name of Hummingboard).
Based on the work from Jon Nettleton <jon.nettleton@gmail.com>.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
|
|
|
|
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
|
|
Access the OneNAND 1KiB window on the VPAC270 as an SRAM instead of accessing
it as a burst-RAM. This fixes a problem where the board failed to reboot
sometimes as the CPU couldn't start executing from the OneNAND 1KiB window.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
|