| Age | Commit message (Collapse) | Author |
|---|
|
This commit fixes a simple typo: sPL --> SPL.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
|
|
There might be hardware configurations where 64-bit data accesses
to NVMe registers are not supported properly. This patch removes
the readq/writeq so always two 32-bit accesses are used to read/write
64-bit NVMe registers, similarly as it is done in Linux kernel.
This patch fixes operation of NVMe devices on RPi4 Broadcom BCM2711 SoC
based board, where the PCIe Root Complex, which is attached to the
system through the SCB bridge.
Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely
the 64-bit wide register accesses initiated by the CPU are not properly
translated to a sequence of 32-bit PCIe accesses.
nvme_readq(), for example, always returns same value in upper and lower
32-bits, e.g. 0x3c033fff3c033fff which lead to NVMe devices to fail
probing.
This fix is analogous to commit 8e2ab05000ab ("usb: xhci: Use only
32-bit accesses in xhci_writeq/xhci_readq").
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2021.1
----------------
CI: https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/5680
- fixes for Variscite dart6ul
- imx8mp : increase malloc area
- fixes for bx50v3
- imx8m: HS400ES and UHS for EVK
- imx8qm-rom7720: fix phy bind
|
|
This reverts commit 828d32621686aec593076d16445d39b9b8d49c05.
This change revers code which asserting PERST# signal when unloading
driver. Driver's remove callback is still there as it is used for other
functionality.
Asserting PERST# signal prior booting kernel is causing that A3720 boards
(Turris MOX and Espressobin) with stable Linux kernel versions 4.14 and
4.19 are not able to detect some PCIe cards (e.g. Compex WLE200 and WLE900)
and anymore. When PERST# signal is not asserted these cards are detected
correctly. As this is regression for existing stable Linux kernel versions
revert this problematic change in U-Boot.
To make cards working with OpenWRT 4.14 kernel it is needed to disable link
training prior booting kernel, which is already done in driver's remove
callback.
Described issue is in Linux kernel pci aardvark driver which is (hopefully)
fixed in latest upstream versions. Latest upstream versions should be able
to initialize PCIe bus and detects cards independently of the link training
and PERST# signal state.
So with this change, U-Boot on A3720 boards should be able to boot OpenWRT
4.14 kernel, stable 4.14 and 4.19 kernels and also latest mainline kernels.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use 0x%2lx to print the i2c bus base address in hexadecimal format
instead of printing as an integer.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
|
|
Add Micron MT25QL01G flash, used on AST2600 board.
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add SPI Flash controller driver for Cortina Access
CAxxxx SoCs
Signed-off-by: Pengpeng Chen <pengpeng.chen@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Vignesh R <vigneshr@ti.com>
CC: Tom Rini <trini@konsulko.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The designware ssi device has "broken" chip select behaviour [1], and needs
specific manipulation to use the built-in chip select. The existing fix is
to use an external GPIO for chip select, but typically the K210 has SPI3
directly connected to a flash chip with dedicated pins. This makes it
impossible to use the spi_xfer function to use spi, since the CS is
de-asserted in between calls. This patch adds an implementation of
exec_op, which gives correct behaviour when reading/writing spi flash.
This patch also rearranges the headers to conform to U-Boot style.
[1] https://lkml.org/lkml/2015/12/23/132
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
CTRLR0 can have several different layouts depending on the specific device
(dw-apb-ssi vs dwc-ssi), and specific parameters set during synthesis.
Update the driver to support three specific configurations: dw-apb-ssi with
SSI_MAX_XFER_SIZE=16, dw-apb-ssi with SSI_MAX_XFER_SIZE=32, and dwc-ssi.
dw-apb-ssi is the version of the device on Altera/Intel SoCFPGAs, MSCC
SoCs, and Canaan Kendryte K210 SoCs. This is the only version this driver
supported before this change. The register layout before version 3.23a is:
| 31 .. 16 |
| other stuff |
| 15 .. 10 | 9 .. 8 | 7 .. 6 | 5 .. 4 | 3 .. 0 |
| other stuff | TMOD | MODE | FRF | DFS |
Note that DFS (Data Frame Size) is only 4 bits, limiting transfers to data
frames of 16 bits or less.
In version 3.23a, the SSI_MAX_XFER_SIZE parameter was introduced. This
parameter defaults to 16 (resulting in the same layout as prior versions),
but may also be set to 32. To allow setting longer data frame sizes, a new
DFS_32 register was introduced:
| 31 .. 21 | 20 .. 16 |
| other stuff | DFS_32 |
| 15 .. 10 | 9 .. 8 | 7 .. 6 | 5 .. 4 | 3 .. 0 |
| other stuff | TMOD | MODE | FRF | all zeros |
The old DFS field no longer controls the data frame size. To detect this
layout, we try writing 0xF to DFS. If we read back 0x0, then this device
has SSI_MAX_XFER_SIZE=32.
dwc-ssi is the version of the device on Intel Keem Bay SoCs and Canaan
Kendryte K210 SoCs. The layout of ctrlr0 is:
| 31 .. 16 |
| other stuff |
| 15 .. 12 | 11 .. 10 | 9 .. 8 | 7 .. 6 | 4 .. 0 |
| other stuff | TMOD | MODE | FRF | DFS_32 |
The semantics of the fields have not changed since the previous version.
However, SSI_MAX_XFER_SIZE is effectively always 32.
To support these different layouts, we model our approach on the one
which the Linux kernel has taken. During probe, the driver calls an init
function stored in driver_data. This init function is responsible for
determining the layout of CTRLR0, and supplying the update_cr0 function.
The style of and information behind this commit is based on the Linux MMIO
driver for these devices. Specific reference was made to the series adding
support for Intel Keem Bay SoCs [1].
[1] https://lore.kernel.org/linux-spi/20200505130618.554-1-wan.ahmad.zainie.wan.mohamad@intel.com/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This should reduce the size of the struct, and also groups more similar
fields together.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This function does nothing but wrap dw_write.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
A few registers had slightly different names from what is in the datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Using an fdt-specific function causes problems when compiled with a live
tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This property is named differently than other SPI drivers with the same
property, as well as the property as used in Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This allows different log levels to be enabled or disabled depending on the
desired level of verbosity. In particular, it allows for general debug
information to be printed while excluding more verbose logging which may
interfere with timing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The resting state of MOSI is high when nothing is driving it. If we drive
it low while recieving, it looks like we are transmitting 0x00 instead of
transmitting nothing. This can confuse slaves (like SD cards) which allow
new commands to be sent over MOSI while they are returning data over MISO.
The return of MOSI from 0 to 1 at the end of recieving a byte can look like
a start bit and a transmission bit to an SD card. This will cause the card
to become out-of-sync with the SPI device, as it thinks the device has
already started transmitting two bytes of a new command. The mmc-spi driver
will not detect the R1 response from the SD card, since it is sent too
early, and offset by two bits. This patch fixes transfer errors when using
SD cards with dw spi.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
U-Boot is able to erase bad mtd blocks on raw nand devices, but this
is not true for spinand flashes. Lets enable this feature for spinand
flashes as well. This is extemelly useful for flash testing.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@oktetlabs.ru>
|
|
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
|
|
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
|
|
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07eedf ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
|
|
According to the mx25l12805d datasheet it supports using 4K or 64K sectors.
So lets add the SECT_4K to enable 4K sector usage.
Datasheet: https://www.mxic.com.tw/Lists/Datasheet/Attachments/7321/MX25L12805D,%203V,%20128Mb,%20v1.2.pdf
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add Winbond W25M512JW flash device description.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add Winbond W25M512JV flash device description.
Linux already has the flash entry present. A snippet below:
{ "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024...},
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Define LOG_CATEGORY and change printf and pr_*
to dev_ (when dev is available) or log_ macro.
This patch adds the support of logging feature with log command
(filtering, display of device name in trace) and allows to
suppress traces via the syslog driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
- r8152, xhci fixes
|
|
Remove the redundant setting for USB_RX_EARLY_SIZE. Besides, for
RTL8153B, it is necessary to notify the hardware of the changes
of the aggregation settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
|
|
The r8152_eth_probe() may allocate a memory for ss->dev_priv.
It has to be freed if r8152_eth_probe() fails finally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
|
|
For bulk IN transfer, the codes will set ISP flag to request event TRB
being generated by xHC for the case of short packet. So when encountering
buffer-cross-64K-boundary (which we will divide payload and enqueuqe
more than 1 transfer TRB), and the first TRB ends up with a short packet
condition it will trigger an short packet code transfer event per that
flag and cause more than 1 event TRB generated for this transfer.
However, current codes will only handle the first transfer event TRB
then mark current transfer completed, causing next transfer
failure due to event TRB mis-match.
Such issue has been observed on some Layerscape platforms (LS1028A,
LS1088A, etc) with USB ethernet device.
This patch adds a loop to make sure the event TRB for last transfer TRB
has been handled in time.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use generic Synopsys DesignWare 3 driver on Intel Edison.
For now it's just a stub which allows future refactoring.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This fixes the wrong usage of clrsetbits_le32(), badly setting the set argument.
Fixes: c4c726c26b ("pinctrl: meson: add pinconf support")
Reported-by: Anton Arapov <arapov@gmail.com>
Reported-by: Otto Meier <gf435@gmx.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
dwc3_meson_g12a_force_mode() sets the dr-mode of the USB PHY. However
it skips setting the mode if it matches the one done during driver probe
(stored in private structure). This fails if the mode has been changed
to other value and then back to initial one. Fix this by configuring the
dr-mode always, regadless of the one set at the driver probe).
This fixes operation of USB gadget based drivers when they are initialized
for the second time.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
|
|
Read PFE ESBC header flash with spi_flash_read API
- logs as follows,
Net: SF: Detected s25fs512s with page size 256 Bytes, erase size 256
KiB, total 64 MiB
"Synchronous Abort" handler, esr 0x96000210
elr: 000000008206db44 lr : 0000000082004ea0 (reloc)
elr: 00000000b7ba6b44 lr : 00000000b7b3dea0
x0 : 00000000b79407e8 x1 : 0000000040640000
x2 : 0000000000000050 x3 : 0000000000000000
x4 : 000000000000000a x5 : 0000000000000050
x6 : 0000000000000366 x7 : 00000000b7942308
x8 : 00000000b76407c0 x9 : 0000000000000008
x10: 0000000000000044 x11: 00000000b7634d1c
x12: 000000000000004f x13: 0000000000000044
x14: 00000000b7634d98 x15: 00000000b76407c0
x16: 0000000000000000 x17: 0000000000000000
x18: 00000000b7636dd8 x19: 0000000000000000
x20: 00000000b79407d0 x21: 00000000b79407e8
x22: 0000000040640000 x23: 00000000b7634e58
x24: 0000000000000000 x25: 0000000003800000
x26: 00000000b7bdd000 x27: 0000000000000000
x28: 0000000000000000 x29: 00000000b7634d10
Code: d2800003 eb03005f 54000101 d65f03c0 (f8636826)
Resetting CPU ...
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Fixes: commit 8ec619f8fd84 ("pci: layerscape: Fixup PCIe EP
mode DT nodes for LX2160A rev2")
This added the PCIe EP nodes fixup of LX2160A, but it
didn't update the condition value when there isn't a
property 'apio-wins'.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Fixed checkpatch error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
resource "config" is required to have minimum 4KB space
to access all config space of PCI Express EP.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
resource "config" is required to have minimum 8KB space
as per hardware documentation.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Print pcie controller number starting from 1
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
|
|
Print pcie controller number starting from 1
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[Trimmed subject]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
|
|
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Remove the parsing of atmel,main-osc-bypass DT property as the SAM9X60
have no support for crystal oscillator bypass. Setting this bit might
affect the device functionality.
Fixes: a64862284f65 ("clk: at91: sam9x60: add support compatible with CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Add SPL_DM_PMIC_PCA9450 symbol to Kconfig.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The I2C address is 0x25, not 0x35. This according to the datasheet and
tests with a PCA9450A.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the
card clock will be divied by 2 automatically by the host. So need
to first config the DDR_EN correctly, then update the card clock.
This will make sure the actual card clock is as our expected.
IC also suggest config the DDR_EN firstly, then config the clock
divider.
For HS400/HS400ES mode, need to config the strobe dll, this need
to based on the correct target clock rate, so need to do this after
clock rate is update.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add wait_dat0() support, upper layer will use this callback.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
This patch fixes this clk issue on I2C on imx8qm
=> i2c bus
Bus 3: i2c@5a830000
=> i2c dev 3
Setting bus to 3
Failed to enable ipg clk
Failure changing bus number (-524)
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
The Kontron SMARC-sAL28 board uses that flash.
This is the same change as in the linux commit f3418718c0ec ("mtd:
spi-nor: Add support for w25q32jwm").
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Leo Krueger <leo.krueger@zal.aero>
|
