summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-11-13net: remove unused CONFIG_AT91_LEGACYAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13i2c: switch from AT91 legacy to ATMEL legacyAndreas Bießmann
Since the required API is gpio which is enclosed with CONFIG_ATMEL_LEGACY use that switch here. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Heiko Schocher <hs@denx.de>
2013-11-13video: remove AT91 legacy API from bus_vcxkAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2013-11-12usb, g_dnl: make bcdDevice value configurableHeiko Schocher
add the possibility to set the bcdDevice number board specific. Therefore the weak function g_dnl_get_board_bcd_device_number() is introduced. Used on the siemens boards. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
2013-11-11am33xx: Make SoC bootcount driver have its own symbolTom Rini
Some am33xx boards may not use the RTC block for bootcount (as it may not be wired up for the board) and use some other facility. So add another symbol for the bootcount driver for the IP block. Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2013-11-11bootcount: store bootcount var in environmentHeiko Schocher
If no softreset save registers are found on the hardware "bootcount" is stored in the environment. To prevent a saveenv on all reboots, the environment variable "upgrade_available" is introduced. If "upgrade_available" is 0, "bootcount" is always 0 therefore no need to save the environment on u-boot boot, if "upgrade_available" is 1 "bootcount" is incremented in the environment and environment gets written on u-boot start. So the Userspace Applikation must set the "upgrade_available" and "bootcount" variable to 0 (for example with fw_setenv), if a boot was successfully. Signed-off-by: Heiko Schocher <hs@denx.de>
2013-11-09Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
2013-11-08Merge branch 'master' of git://www.denx.de/git/u-boot-usbTom Rini
2013-11-08netconsole loses 2nd character of inputSuriyan Ramasami
Netconsole loses the second character when used as input by either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX Before a nc_send_packet() to echo the input, a check is done to see if nc_ether is valid. If its not, it waits for an arp request and then sends the packet (which contains the first character of line to be displayed as output). As part of reaping the arp request, the second character is consumed. We protect this by making the call to NetLoop(NETCONS) between input_recursion. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2013-11-08serial: s5p: Staticize local functionsAxel Lin
Staticize local functions in s5p serial driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2013-11-08serial: xuartlite: Staticize local functionsAxel Lin
Staticize local functions in xuartlite driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Stefan Roese <sr@denx.de> Tested-by: Michal Simek <monstr@monstr.eu>
2013-11-08serial: mxs_auart: Staticize local functionsAxel Lin
Staticize local functions in mxs_auart driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Marek Vasut <marex@denx.de>
2013-11-08usb: dfu: make nand upload workingBo Shen
Nowhere pass a value to len, which always 0, make no transfer which cause uploading failed. This patch make nand upload working. However it needs enough malloc buffer to store read data, that means the buffer at least equal to the upload partition size, or else it doesn't work. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-11-08usb, g_dnl: make iSerialNumber board configurableHeiko Schocher
add the possibility to set the iSerialNumber board specific. Default value for iSerialNumber is 0x0. This value can changed board specific through the new function g_dnl_set_serialnumber() which must be called from the board specific function g_dnl_bind_fixup(). Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2013-11-08usb: dfu: correct dfu buffer inited valueBo Shen
After dfu buffer is initialized, the buffer should be all available, while not 0. Initialize its value to min(dfu_buf_size, dfu->r_left). Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2013-11-08usb: dfu: decrease dfu->r_left along with the transferBo Shen
The value of dfu->r_left need decrease along with the transfer Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-11-08usb: ohci-hcd: submit_common_msg: report actual_length properlyMateusz Kulikowski
submit_common_msg should report amount of data passed from/to device. Instead, it always returned size requested by Host. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
2013-11-08usb: ums: add ums exit feature by ctrl+c or by detach usb cablePrzemyslaw Marczak
This patch allows exiting from UMS mode to u-boot prompt by detaching usb cable or by pressing ctrl+c. Add new config: CONFIG_USB_CABLE_CHECK. If defined then board file should provide function: usb_cable_connected() (include/usb.h) that return 1 if cable is connected and 0 otherwise. Changes v2: - add a note to the README Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
2013-11-08usb: ums: fix disk capacity miscalculation and code cleanupPrzemyslaw Marczak
This patch prevents: - ums disk capacity miscalculation because of integer overflow Changes v2: - Prevents passing zero size disk capacity to ums gadget driver - Change function ums_get_capacity() to ums_disk_init() and do ums disk initialization before gadget init - Remove unnecessary code from mass storage driver Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
2013-11-08usb: ums: code refactoring to improve reusability on other boards.Przemyslaw Marczak
This patch introduces some cleanups to ums code. Changes: ums common: - introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in usb_mass_storage.h both default values as 0 if board config doesn't define them common cleanup changes: - change name of struct "ums_board_info" to "ums" - "ums_device" fields are moved to struct ums and "dev_num" is removed - change function name: board_ums_init to ums_init - remove "extern" prefixes from usb_mass_storage.h cmd_usb_mass_storage: - change error() to printf() if need to print info message - change return values to command_ret_t type at ums command code - add command usage string Changes v2: ums common: - always returns number of read/write sectors - coding style clean-up ums gadget: - calculate amount of read/write from device returned value. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com>
2013-11-08cosmetic: remove empty lines at the top of fileMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08Add support for SX151x SPI GPIO ExpandersViktar Palstsiuk
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
2013-11-07Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-06fpga: zynqpl: Do not place bitstream below 1MBMichal Simek
DMA doesn't work when src is placed below 1MB limit. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-11-06fpga: zynqpl: Add dcache flush supportJagannadha Sutradharudu Teki
Buffers must be cache and dma aligned. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-11-05Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-04arm: atmel: get rid of too many ifdefferyBo Shen
Get rid of too many ifdeffery in usb ohci driver Add following two configuration for USB clock selecting - CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock - CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04arm: atmel: at91sam9n12ek: add usb host supportBo Shen
Add usb host support for at91sam9n12ek board. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04net: macb: get DMA bus width from design config registerBo Shen
Get DMA bus width from design config register Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04Merge branch 'master' of git://git.denx.de/u-boot-blackfinTom Rini
Easy to resolve conflict on the GPIO change. Conflicts: arch/blackfin/cpu/Makefile Signed-off-by: Tom Rini <trini@ti.com>
2013-11-04blackfin: Move machine specific gpio_port_t structure back to blackfin arch ↵Steven Miao
folder. The gpio register mappings are different among blackfin processors. Signed-off-by: Steven Miao <realmz6@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-11-01nand, davinci: add special UBL ecc positionHeiko Schocher
enable the RBL/UBL ECC layout through CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define see for more info: http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Scott Wood <scottwood@freescale.com>
2013-11-01TI:am33xx: Add bootcount support to ti_am335x_common.hTom Rini
Enable the bootcount driver for am335x in general. We leave adding a bootlimit and altbootcmd to the environment to the board ports. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01bootcount_davinci: Switch to scratch register #2Tom Rini
The RTC IP block here provides 3 scratch registers. Currently when using DeepSleep on am335x the scratch0/1 registers are used so moving ourself to scratch2 makes cooperation easier. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01am33xx, davinci: Create and use <asm/davinci_rtc.h>Tom Rini
Create a common header file for the RTC IP block that is shared between davinci and am33xx. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01drivers/rtc/davinci.c: Reference DAVINCI_RTC_BASE more directlyTom Rini
We shouldn't rely on a define to hide this cast for us. Signed-off-by: Tom Rini <trini@ti.com>
2013-10-31drivers: move some drivers to drivers/MakefileMasahiro Yamada
This commit moves some drivers subdirectory entry from the toplevel Makefile to drivers/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31drivers: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31drivers: usb: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31drivers: mtd: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31drivers: net: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31imx_watchdog: do not soft-reset while watchdog initAnatolij Gustschin
Currently the driver clears WCR_SRS bit when enabling the watchdog and this causes a software reset. Do not clear WCR_SRS. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2013-10-31nand_util.c: Correct licensingTom Rini
Prior to SPDX licensing this file was GPL-2.0 with Freescale granting rights for "or later" for their contributed code. We incorrectly moved this file to GPL-2.0+, so correct it to GPL-2.0. In addition we cannot easily denote in the file where or what code is "or later", so just set that aside for now and the file as a whole is GPL-2.0 regardless. Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-10-31powerpc/esdhc: Add 3.3v voltage support in esdhc capacity registerHaijun.Zhang
T4240QDS eSDHC host capabilities reigster should have VS33 bit define. Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity missing Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31esdhc: memset mmc struct before putting into useHaijun.Zhang
struct mmc should be clear to all '0' after malloc to avoid unexpect variable value. Like mmc->has_init = xxx. In this case mmcinfo will believe the card had been initialized before and skip the initialization. Test on P5040 and T4240, Error Log: => mmcinfo Device: FSL_SDHC Manufacturer ID: 0 OEM: 0 Name: Tran Speed: 0 Rd Block Len: 0 MMC version 0.0 High Capacity: No Capacity: 0 Bytes Bus Width: 0-bit => Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com> Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31Powerpc/esdhc: Add simple description of esdhc registerHaijun.Zhang
Add some descriptions for esdhc register for easily using. Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31powerpc/esdhc: Map register for eSDHC Host Controller V3.0Haijun.Zhang
eSDHC host controller has new register to support SD Spec 3.0. And the according host controller version was Freescale eSDHC Version 3.0. Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31DWMMC: SMDK5420: Disable SMU for eMMCRajeshwari Shinde
SMDK5420 has a new Security Management Unit added for dwmmc driver, hence, configuring the control registers to support booting via eMMC. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31mmc: sdhci: Avoid commands errors by simple timeout adaptation.Przemyslaw Marczak
Old command timeout value was too small and it caused I/O errors which led to uncompleted read/write/erase operations and filesystem errors. Timeout adaptation fixes this issue. Changes in sdhci_send_command() function: - change timeout variable to static - increase default command timeout to 100 ms - add definition of max command timeout value, which can be redefined in each board config file - wait for card ready state for max defined time if it doesn't exceed defined maximum or return COMM_ERR Once successfully increased timeout value will be used in next function call. This fix was tested on Goni, Trats, Trats2 boards by testing UMS on MMC storage. Changes v2: - move global variable cmd_timeout into function sdhci_send_command() - change condition "==" to ">=" when comparing time with timeout - print information about timeout increasing and card busy timeout Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31mmc: dw_mmc: change the callback function name.Jaehoon Chung
To prevent the confusion, use the get_mmc_clk() instead of mmc_clk(). get_mmc_clk() is more exactly name. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-18 03:03:49 +0000