| Age | Commit message (Collapse) | Author |
|---|
|
Prepare the future use of an helper to move the data pointer (the
column) of the NAND chip by renaming nand_reset_column() to
nand_change_column(). Resetting the column is just a matter of giving 0
as argument.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
When changing the column, the ONFI specification states that a minimum
time of tCCS (Change Column Setup time) must elapse between the last
address cycle is asserted on the bus and the first data cycle is
clocked. An usual value for average NANDs is 500 nanoseconds. Round it
up to 1 microsecond to be safe.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Executing a command is matter of always doing the following sequence:
* Waiting for the FIFO to be empty so we can fill it with the new
command.
* Clearing the status register.
* Writing the command in the FIFO.
* Waiting for the command to finish.
Add a nand_exec_cmd() helper to handle this instead of repeating the
logic through the various functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
It is best practice to always clear the status register before executing
a command to be sure that the status read afterwards is relevant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
One bit in the control registers indicates if the NAND controller is
ready to receive a new command. Otherwise, the command FIFO is full and
we should wait for this bit to flip. It then states that the last
command has been processed and the FIFO is now free to welcome another
command.
Add this sanity check before starting any new command.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The pattern of polling on a status register until a bit is set or a
timeout occurs is repeated multiple times in the driver. Mutualize the
code by introducing the nand_wait_int() helper that does wait for the
bit to flip or returns an error in case of timeout.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Change NFC_SEND_ADR to NFC_SEND_ADDR.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
In the nand_read_buffer() step, the seed is calculated by doing a modulo
by conf->nseeds which is always zero when not using the randomizer (most
of SLC NANDs).
This situation turns out to lead to a run time freeze with certain
toolchains.
Derive this seed only when the randomizer is enabled (and conf->nseeds
logically not zero), exactly like what has been done before with an
identical situation, see commit ea3f750c73e3 ("nand: sunxi: Fix modulo
by zero error").
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.
For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add simple and meaningful kconfig option for pmic_bus.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove busy looping during watchdog reset.
Each polling of W_PEND_WTGR bit ("finish posted
write") after watchdog reset takes 120-140us
on BeagleBone Black board. Current U-Boot code
has watchdog resets in random places and often
there is situation when watchdog is reset
few times in a row in nested functions.
This adds extra delays and slows the whole system.
Instead of polling W_PEND_WTGR bit, we skip
watchdog reset if the bit is set. Anyway, watchdog
is in the middle of reset *right now*, so we can
just return.
This noticeably increases performance of the
system. Below are some measurements on BBB:
- DFU upload over USB 15% faster
- fastboot image upload 3x times faster
- USB ep0 transfers with 4k packets 20% faster
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
To support set/get the clock rate, add set/get_rate operations.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
As said in the SAMA5D2 datasheet, the PLLA clock must be divided
by 2 by writing the PLLADIV2 bit in PMC_MCKR, if the ratio between
PCK and MCK is 3 (MDIV = 3). This is the purpose of the driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
Add USB clock driver to configure the input clock and the divider
in the PMC_USB register to generate a 48MHz and a 12MHz signal to
the USB Host OHCI.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
|
|
omap3_spi_set_speed|mode redeclared bus symbol, fix the same.
error:
drivers/spi/omap3_spi.c: In function ‘omap3_spi_set_speed’:
drivers/spi/omap3_spi.c:650:18: error: ‘bus’ redeclared as different kind of symbol
struct udevice *bus = dev->parent;
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
|
|
For STM32F4 and F7 SoCx family, a specific stm32.h file exists.
Some common defines are duplicated or even unused in each of
these stm32.h.
Factorize all common definition in arch/arm/include/asm/stm32f.h and keep
specific definitions in each arch/arm/include/asm/arch-stm32fx/stm32.h.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
DSI clock is available on STM32F769-disco and
STM32F469-disco board.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Implement set_rate() for LTDC clock only, set_rate for other
clocks will be added if needed. This is needed by future LTDC driver
improvements.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Configure SAI PLL configuration to generate LTDC pixel clock on
the PLLSAIR output.
PLLSAI is enabled only if CONFIG_VIDEO_STM32 flag is set.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Rework the way SDMMC clock get rate is done in a more
generic way :
_ Add stm32_clk_get_pllsai_rate() which give the PLLSAI
indicated output rate.
_ Add stm32_clk_get_pllsai_vco_rate() which give the VCO
internal rate.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Initially, 48Mhz for SDIO clock was generated from SAI pll for
STM32F469 and STM32F746 SoCs, but this solution was not suitable
for STM32F429 SoCs.
A generic solution is to used the PLL_Q output as 48Mhz clock
for all STM32F SOCs family.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use the correct name for RCC_PLLSAICFGR_PLLSAIx_MASK masks.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Wrong parameter was passed to stm32_clk_pll48clk_rate().
sysclk (PLL_p output value) was passed instead of VCO value.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This patch adds "st,pin-ckin" support to activate sdmmc_ckin feature.
When using an external driver (a voltage switch transceiver),
it's advised to select SDMMC_CKIN feedback clock input to sample
the received data.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The hardware flow control functionality is used to avoid
FIFO underrun (TX mode) and overrun (RX mode) errors.
The behavior is to stop SDMMC_CK during data transfer and
freeze the SDMMC state machines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
d1cfgr register was used to calculate the domain 3
prescaler value instead of d3cfgr.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
For timer clock, an additional prescaler is used which
was not taken into account previously.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
For timer clock, an additionnal prescaler is used which was
not taken into account previously.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This timer driver is using GPT Timer (General Purpose Timer)
available on all STM32 SOCs family.
This driver can be used on STM32F4/F7 and H7 SoCs family
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
|
|
|
|
use live dt api to get base addr
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).
Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.
After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.
- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.
- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.
After the changes the suspicious defconfigs passes building.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The previous code tried to update the PHY parameters without waiting for
autonegotiation to complete. This caused wrong values to be written to
the EMAC in sun8i_adjust_link(). As a result, any commands that called
eth_start() before autonegotiation completed would find the network
nonfunctional. Fix this by using the correct function to start up the
PHY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
With CONFIG_DM_MMC the BananaPi does not detect SD cards.
The sunxi device trees use the cd-inverted property to indicate that
the card detect is inverted.
This property is documented in Linux kernel devicetree/bindings/mmc/mmc.txt
The property is not marked as deprecated.
A similar patch was posted by Tuomas but is in status "Changes Requested".
https://patchwork.ozlabs.org/patch/850377/
This patch is a stripped down version of his patch.
Suggested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This SUNXI variant SPL SPI code doesn't use either SPI or
SPL_FLASG subsystems due to size constraints and also placing
this code in drivers/mtd/spi will unnecessary build SPI_FLASH
code(if defined) which never required, hence moved to arch area.
And also renamed the file according to kconfig which resembles
proper name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
set_mode, set_seed functions has separate function pointers
in dm_spi_ops, so use them in relevent one instead of
calling from claim_bus.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Boards adp-ae3xx_defconfig, nx25-ae250_defconfig
already enabled DM_SPI, so non-dm code make no use
of it hence droped.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt on Raspberry Pis that use pl011 for serial.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
