summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-12-20phy: add Micrel KS8721BL phy definitionVladimir Zapolskiy
This adds support for the Micrel KS8721BL/SL PHY. The definition is taken from the correspondent datasheet. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2011-12-20mvgbe: remove setting of ethaddr within the driverMichael Walle
A network driver should not touch the environment at all. This patch fixes this behaviour by removing the code for setting a default/randomized MAC address. Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Eric Cooper <ecc@cmu.edu> Cc: Jason Cooper <u-boot@lakedaemon.net> Cc: Siddarth Gore <gores@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Simon Guinot <simon.guinot@sequanux.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2011-12-16USB: Use (get|put)_unaligned for accessing wMaxPacketSizeTom Rini
In 9792987721c7980453fe6447c3fa6593b44f8458 Stefan describes a usecase where the previous behavior of leaving wMaxPacketSize be unaligned caused fatal problems. The initial fix for this problem was incomplete however as it showed another cases of non-aligned access that previously worked implicitly. This switches to making sure that all access of wMaxPacketSize are done via (get|put)_unaligned. In order to maintain a level of readability to the code in some cases we now use a variable for the value of wMaxPacketSize and in others, a macro. Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Remy Bohmer <linux@bohmer.net> OpenRISC: Tested-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Beagleboard xM, Pandaboard run-tested, s5p_goni build-tested. Signed-off-by: Tom Rini <trini@ti.com>
2011-12-16USB: ULPI: increase error case verbosityIgor Grinberg
Add the argument value to the error message. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Simon Glass <sjg@chromium.org>
2011-12-16USB: ULPI: clean a mixup of return typesIgor Grinberg
Clean a mixup between u32 and int as a return type for functions returning error values. Use int as it is native (and widely used) return type. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Simon Glass <sjg@chromium.org>
2011-12-16USB: ULPI: switch argument type from u8 to unsignedIgor Grinberg
There is no benefit in using u8, so switch to unsigned to reduce the binary image size (by 20 bytes). Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Simon Glass <sjg@chromium.org>
2011-12-11USB: Add generic ULPI layer and a viewportJana Rapava
Add partial ULPI specification implementation that should be enough to interface the ULPI PHYs in the boot loader context. Add a viewport implementation for Chipidea/ARC based controllers. Signed-off-by: Jana Rapava <fermata7@gmail.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Remy Bohmer <linux@bohmer.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Simon Glass <sjg@chromium.org>
2011-12-11USB: EHCI: Allow EHCI post-powerup configuration in board filesMarek Vasut
This patch allows USB to work on some hosts, which need additional frobing after the host was powered up via regular USB powerup sequence. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
2011-12-11USB: MX5: Add MX5 usb post-init callbackMarek Vasut
This is useful for USB Transceivers init etc. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
2011-12-11USB: MX5: Abstract out mx51 USB pixmux configurationMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
2011-12-11USB: MX5: add generic USB EHCI support for mx51 and mx53Wolfgang Grandegger
It's derived from ehci-mxc and uses the header files of the ehci-fsl interface. The callback board_ehci_hcd_init() has been introduced to allow for board-specific setup when USB is started. Signed-off-by: Wolfgang Grandegger <wg@denx.de> CC: Stefano Babic <sbabic@denx.de> CC: Remy Bohmer <linux@bohmer.net>
2011-12-11usb:gadget:s5p USB Device Controller (UDC) implementationLukasz Majewski
This commit provides UDC driver support for Samsung's SoC family of processors. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Remy Bohmer <linux@bohmer.net>
2011-12-11ehci: speed up initializationVincent Palatin
According to EHCI specification v1.0, the controller should stabilize the power on a port at most 20 ms after the port power bit transition. So, we put this setting in the virtual descriptor corresponding field, (bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each controller initialization/enumeration. Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
2011-12-11usbtty: init endpoints prior to startup eventsStefan Herbrechtsmeier
On some usb device controllers (pxa) the endpoint configuration must be programmed prior to enable it. Signed-off-by: Stefan Herbrechtsmeier <sherbrec@cit-ec.uni-bielefeld.de> CC: Marek Vasut <marek.vasut@gmail.com> CC: Remy Bohmer <linux@bohmer.net>
2011-12-11pxa: convert pxa27x_udc to use read and write functionsStefan Herbrechtsmeier
Signed-off-by: Stefan Herbrechtsmeier <sherbrec@cit-ec.uni-bielefeld.de> CC: Marek Vasut <marek.vasut@gmail.com> CC: Remy Bohmer <linux@bohmer.net>
2011-12-11USB: Add usb_event_poll() to get keyboards working with EHCIMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Remy Bohmer <linux@bohmer.net>
2011-12-11USB: gadaget: add Marvell controller supportLei Wen
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-12-11USB: Fix complaints about strict aliasing in OHCI-HCDMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-10drivers/net/at91_emac.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: at91_emac.c: In function 'at91emac_phy_init': at91_emac.c:244:20: warning: variable 'duplex' set but not used [-Wunused-but-set-variable] at91_emac.c:244:13: warning: variable 'speed' set but not used [-Wunused-but-set-variable] Use new debug_cond() to fix these warnings. In the result, anumber of inconsistent printf() formats are detected: at91_emac.c: In function 'at91emac_read': at91_emac.c:147:2: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'struct at91_emac_t *' [-Wformat] at91_emac.c: In function 'at91emac_write': at91_emac.c:157:2: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'struct at91_emac_t *' [-Wformat] at91_emac.c:157:2: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'short unsigned int *' [-Wformat] at91_emac.c: In function 'at91emac_recv': at91_emac.c:451:3: warning: format '%d' expects argument of type 'int', but argument 2 has type 'long unsigned int' [-Wformat] at91_emac.c:451:3: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'long unsigned int' [-Wformat] Fix these, too. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Jens Scharsig <js_at_ng@scharsoft.de> Cc: Andreas Bießmann <andreas.devel@gmail.com> Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-12-10drivers/net/ne2000_base.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: ne2000_base.c: In function 'dp83902a_send': ne2000_base.c:282:7: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] ne2000_base.c: In function 'dp83902a_RxEvent': ne2000_base.c:376:5: warning: variable 'rsr' set but not used [-Wunused-but-set-variable] ne2000_base.c: In function 'dp83902a_TxEvent': ne2000_base.c:513:5: warning: variable 'tsr' set but not used [-Wunused-but-set-variable] ne2000_base.c: In function 'dp83902a_ClearCounters': ne2000_base.c:550:17: warning: variable 'cnt3' set but not used [-Wunused-but-set-variable] ne2000_base.c:550:11: warning: variable 'cnt2' set but not used [-Wunused-but-set-variable] ne2000_base.c:550:5: warning: variable 'cnt1' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-10Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
* 'master' of git://git.denx.de/u-boot-arm: M28: Cleanup memsize.o OOT build i.MX28: Move SPL to arch/arm/cpu/arm926ejs/mx28 M28: Fix typo M28: Document that units has to be set to sectors on SD bootcard i.mx: i.mx6q: add the initial support for i.mx6q ARM2 board i.mx: mxc_gpio: add the i.mx6q support i.mx: add the initial support for freescale i.MX6Q processor i.mx: introduce the armv7/imx-common folder S5PC2XX: Rename S5pc2XX to exynos tegra2: Don't use board pointer before it is set up tegra2: Remove unneeded 'dynamic ram size' message tegra2: Remove unused low-level Tegra2 UART code tegra2: Remove unneeded config option tegra2: Remove unneeded boot code tegra2: Enable instruction cache arm: Move CP15 init out of cpu_init_crit() tegra2: Simplify tegra_start() boot path tegra2: Add arch_cpu_init() to fire up Cortex-A9 tegra2: Use new GPIO APIs in gpio_config_uart() tegra2: Add support for Ventana tegra2: Modify MMC driver to handle power and cd GPIOs tegra2: Move board_mmc_init into board files
2011-12-09i.mx: mxc_gpio: add the i.mx6q supportJason Liu
Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2011-12-09tegra2: Remove unused low-level Tegra2 UART codeSimon Glass
This was used by the AVP in early boot but is no longer used. Unless we plan to enable it somehow it is not needed. In any case we should try to use the ns16550 driver instead as it has the same code. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-09tegra2: Use new GPIO APIs in gpio_config_uart()Stephen Warren
... rather than open-coding the register accesses. However, gpio_request() typically stores the "label" parameter in a global data structure. This causes problems when called from gpio_config_uart(), since the code is running before relocation. To solve this, pass a NULL string to gpio_request(), and modify gpio_request() not to touch the string if it's NULL. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-09tegra2: Modify MMC driver to handle power and cd GPIOsStephen Warren
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and modify that function to perform all required GPIO initialization. This removes the need for board files to perform these operations. Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which GPIOs to use. Update affected call-sites in seaboard.c and harmony.c. Note that this change should make all SD ports work on Harmony, since the required GPIO setup is now being performed. v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change. Remove prototype of gpio_config_mmc() from board.h Signed-off-by: Stephen Warren <swarren@nvidia.com> Cc: Andy Fleming <afleming@gmail.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-09omap: TWL4030 Bump VMMC1 interface voltage from 3V to 3.15VAsh Charles
MMC interfaces are specified to be 3.3V compatible with an operating voltage range of 3.1V to 3.5V for SD cards. This change affects hardware using TWL4030 (TPS6595x) PMICs and should improve the reliability when communicating with marginally-spec'd MMC devices. 3.15V is the highest possible level for this chip. This patch has been tested on a Gumstix Overo board. Signed-off-by: Ash Charles <ash@gumstix.com> Tested-by: Steve Sakoman <steve@sakoman.com>
2011-12-09drivers/gpio/da8xx_gpio.c: Fix build warningAnatolij Gustschin
Fix: da8xx_gpio.c: In function 'gpio_toggle_value': da8xx_gpio.c:208:23: warning: variable 'bank' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-12-09drivers/usb/gadget/ep0.c: Fix GCC 4.6 warningAnatolij Gustschin
Fix: ep0.c: In function 'ep0_get_descriptor': ep0.c:187:8: warning: variable 'cp' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: Remy Bohmer <linux@bohmer.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-09drivers/usb/gadget/core.c: Fix GCC 4.6 warningAnatolij Gustschin
Fix: core.c: In function 'usbd_device_event_irq': core.c:596:21: warning: variable 'state' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: Remy Bohmer <linux@bohmer.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-09drivers/usb/musb/musb_udc.c: Fix GCC 4.6 warningAnatolij Gustschin
Fix: musb_udc.c: In function 'musb_peri_softconnect': musb_udc.c:166:14: warning: variable 'intrtx' set but not used [-Wunused-but-set-variable] musb_udc.c:166:6: warning: variable 'intrrx' set but not used [-Wunused-but-set-variable] musb_udc.c:165:5: warning: variable 'intrusb' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: Remy Bohmer <linux@bohmer.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-09drivers/usb/host/ehci-mxc.c: Fix GCC 4.6 warningAnatolij Gustschin
Fix: ehci-mxc.c: In function 'ehci_hcd_init': ehci-mxc.c:113:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-12-08ne2000: Convert to new net-multi model, fixes build of three boardsBernhard Kaindl
This fixes the build of the two sh boards shmin and r7780mp and qemu-mips which currently fail to build due to dropped pre-CONFIG_NET_MULTI code. This v2 patch minimizes the number of lines in the diff for easy review and to eliminate any possible accidential changes resulting from moving lines of code in the file. This also makes the register function very easy. Any cleanups and improvements are intentionally deferred to follow-up patches to keep this patch as simple and as easy to review as possible. A new driver register function, ne2k_register() calls the existing one-time setup part of the old init function and calls eth_register(). Changes to shmin, r7780mp and qemu-mips: - Call the new ne2k_register() from board_eth_init() of the boards. - Tested using qemu-mips board, - Tested the two renesas / sh boards r7780mp and shmin to compile again, and should work. checkpatch-clean when "--ignore VOLATILE" is added to .checkpatch.conf, and no warnings introduced in none of the three boards using this driver. Signed-off-by: Bernhard Kaindl <bernhard.kaindl@gmx.net>
2011-12-08drivers/net/inca-ip_sw.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: inca-ip_sw.c: In function 'inca_switch_init': inca-ip_sw.c:210:6: warning: variable 'v' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-08Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
* 'master' of git://git.denx.de/u-boot-nand-flash: nand_spl/nand_boot.c: Fix build warning drivers/mtd/nand/nand_spl_load.c: Fix GCC 4.6 warning drivers/mtd/nand/nand_spl_simple.c: Fix GCC 4.6 warnings
2011-12-07drivers/mtd/nand/nand_spl_load.c: Fix GCC 4.6 warningAnatolij Gustschin
Fix: nand_spl_load.c: In function 'nand_boot': nand_spl_load.c:31:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-12-07drivers/mtd/nand/nand_spl_simple.c: Fix GCC 4.6 warningsAnatolij Gustschin
Fix warnings for both cases: definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST: nand_spl_simple.c: In function 'nand_read_page': nand_spl_simple.c:156:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable] not definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST: nand_spl_simple.c: In function 'nand_read_page': nand_spl_simple.c:196:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-12-07video: cfb_console: fix build warningsAnatolij Gustschin
Fix: cfb_console.c:371: warning: 'cursor_state' defined but not used cfb_console.c:372: warning: 'old_col' defined but not used cfb_console.c:373: warning: 'old_row' defined but not used cfb_console.c:435: warning: 'video_invertchar' defined but not used Signed-off-by: Anatolij Gustschin <agust@denx.de> Tested-by: Wolfgang Denk <wd@denx.de>
2011-12-07Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
* 'master' of git://git.denx.de/u-boot-arm: davinci: Remove unwanted memsize.c from hawkboard's nand spl build devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss da850evm: pass board revision info to kernel arch/arm/include/asm/arch-omap5/clocks.h: Fix GCC 4.2 warnings arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings arch/arm/cpu/armv7/omap-common/spl.c: Fix GCC 4.2 warnings MX35: flea3: changes due to hardware revision B MX: serial_mxc: cleanup removing nasty #ifdef M28: Fix OB1 bug in GPIO driver MXS: Add static annotations to dma driver apbh_dma: return error value on timeout Efika: Configure additional regulators for HDMI output mx5: Correct a warning in clock.c MC13892: Add REGMODE0 bits definitions mx51evk: Configure the pins as GPIOs prior to using gpio_get_value mx53smd: Configure the pins as GPIOs prior to using gpio_get_value mx53evk: Configure the pins as GPIOs prior to using gpio_get_value mx53ard: Configure the pins as GPIOs prior to using gpio_get_value mx53loco: Configure the pins as GPIOs prior to using gpio_get_value OMAP3: Add SPL_BOARD_INIT hook AM3517 CraneBoard: Add SPL support AM3517: Add SPL support OMAP3: Add SPL support to omap3_evm OMAP3: Add SPL support to Beagleboard OMAP3 SPL: Add identify_nand_chip function OMAP3 SPL: Rework memory initalization and devkit8000 support OMAP3: Suffix all Micron memory timing parts with their speed OMAP3: Add optimal SDRC autorefresh control values omap3: mem: Add MCFG helper macro OMAP3: Remove get_mem_type prototype OMAP3: Change mem_ok to clear again after reading back OMAP3: Add a helper function to set timings in SDRC OMAP3: Update SDRC dram_init to always call make_cs1_contiguous() omap3: mem: Comment enable_gpmc_cs_config more ARM: davici_emac: Fix condition for number of phy detects arm: printf() is not available in some SPL configurations arm, davinci: add support for am1808 based enbw_cmc board arm, davinci: move misc function in arch tree arm, board/davinci/common/misc.c: Codingstyle cleanup arm, davinci, da850: add uart1 tx rx pinmux config arm, davinci: move davinci_rtc struct to hardware.h arm, davinci: Remove duplication of pinmux configuration code arm, hawkboard: Use the pinmux configurations defined in the arch tree arm, da850evm: Use the pinmux configurations defined in the arch tree arm, da850: Add pinmux configurations to the arch tree arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins arm, davinci: Move pinmux functions from board to arch tree arm, arm926ejs: always do cpu critical inits omap_gpmc: use SOFTECC in SPL if it's enabled nand_spl_simple: add support for software ECC AM3517: move AM3517 specific mux defines to generic header AM35xx: add EMAC support davinci_emac: hardcode 100Mbps for AM35xx and RMII davinci_emac: fix for running with dcache enabled arm926ejs: add noop implementation for dcache ops davinci_emac: conditionally compile specific PHY support davinci_emac: use internal addresses in buffer descriptors davinci_emac: move arch-independent defines to separate header BeagleBoard: config: Really switch to ttyO2 ARM: davinci_dm6467Tevm: Fix build breakage ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused ARM: OMAP3: Remove unused define SDRC_R_C_B ARM: OMAP3: Remove unused define CONFIG_OMAP3430 omap4: fix IO setting omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses omap4460: add ES1.1 identification omap4: emif: fix error in driver omap: remove I2C from SPL omap4460: fix TPS initialization omap: fix cache line size for omap3/omap4 boards omap4: ttyO2 instead of ttyS2 in default bootargs omap: Improve PLL parameter calculation tool start.S: remove omap3 specific code from start.S armv7: setup vector armv7: include armv7/cpu.c in SPL build armv7: disable L2 cache in cleanup_before_linux() arm, arm926ejs: Fix clear bss loop for zero length bss PXA: Move colibri_pxa270 to board/toradex/ PXA: Flip colibri_pxa27x to pxa-common.h PXA: Introduce common configuration header for PXA PXA: Rename pxa_dram_init to pxa2xx_dram_init PXA: Squash extern pxa_dram_init() PXA: Export cpu_is_ and pxa_dram_init functions PXA: Cleanup Colibri PXA270 PXA: Replace timer driver PXA: Add cpuinfo display for PXA2xx PXA: Separate PXA2xx CPU init PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X PXA: Unify vpac270 environment size PXA: Enable command line editing for vpac270 PXA: Adapt Voipac PXA270 to OneNAND SPL PXA: Drop Voipac PXA270 OneNAND IPL PXA: Fixup PXA25x boards after start.S update PXA: Re-add the Dcache locking as RAM for pxa250 PXA: Rework start.S to be closer to other ARMs PXA: Drop XM250 board PXA: Drop PLEB2 board PXA: Drop CRADLE board PXA: Drop CERF250 board Fix regression in SMDK6400 nand: Add common functions to linux/mtd/nand.h Ethernut 5 board support net: Armada100: Fix compilation warnings ARM: remove duplicated code for LaCie boards ARM: add support for LaCie 2Big Network v2 mvsata: fix ide_preinit for missing disks netspace_v2: Read Ethernet MAC address from EEPROM omap3evm: Add support for EFI partitions part_efi: Fix compile errors
2011-12-07Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk
* 'master' of git://git.denx.de/u-boot-video: video: cfb_console: Make the software cursor non-destructive
2011-12-07Introduce generic TPM support in u-bootVadim Bendebury
TPM (Trusted Platform Module) is an integrated circuit and software platform that provides computer manufacturers with the core components of a subsystem used to assure authenticity, integrity and confidentiality. This driver supports version 1.2 of the TCG (Trusted Computing Group) specifications. The TCG specification defines several so called localities in a TPM chip, to be controlled by different software layers. When used on a typical x86 platform during the firmware phase, only locality 0 can be accessed by the CPU, so this driver even while supporting the locality concept presumes that only locality zero is used. This implementation is loosely based on the article "Writing a TPM Device Driver" published on http://ptgmedia.pearsoncmg.com Compiling this driver with DEBUG defined will generate trace of all accesses to TMP registers. This driver has been tested and is being used in three different functional ChromeOS machines (Pinetrail and Sandy Bridge Intel chipsets) all using the same Infineon SLB 9635 TT 1.2 device. A u-boot cli command allowing access to the TPM was also implemented and is being submitted as a second patch. Change-Id: I22a33c3e5b2e20eec9557a7621bd463b30389d73 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> CC: Wolfgang Denk <wd@denx.de>
2011-12-06MX: serial_mxc: cleanup removing nasty #ifdefStefano Babic
The serial driver for iMX SOCs is continuosly changed if a new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port> defines were used only to find the base address for the selected UART. Instead of that, move the base address to the board configuration file and drop all #ifdef from driver. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Marek Vasut <marek.vasut@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Helmut Raiger <helmut.raiger@hale.at> CC: John Rigby <jcrigby@gmail.com> CC: Matthias Weisser <weisserm@arcor.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
2011-12-06M28: Fix OB1 bug in GPIO driverRobert Deliën
This patch fixes a small off-by-one bug in the GPIO driver for the mxs platform that allowed the selection gpio pins of one bank more than the SoC actually has. Signed-off-by: Robert Deliën <robert at delien.nl> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06MXS: Add static annotations to dma driverMarek Vasut
Some functions were internal to the apbh dma driver, so annotate them static. Some of the functions weren't used at all so drop them. This makes the U-Boot binary smaller by about 1500 bytes. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2011-12-06apbh_dma: return error value on timeoutWolfram Sang
When a timeout occurs, the return value is prepared but never returned. Fix that. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Marek Vasut <marek.vasut@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2011-12-06ARM: davici_emac: Fix condition for number of phy detectsPrabhakar Lad
Fix the condition for number of phys in davinci_eth_phy_detect() function. CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT indicates number of phys. From this commit id dc02badab480563b0bf9d3908046ea9d6b22ae63 davinci emac initilazed one less than the number of phy count. Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com> Acked-by: Heiko Schocher <hs@denx.de>
2011-12-06arm, davinci: move davinci_rtc struct to hardware.hHeiko Schocher
move struct davinci_rtc to arch/arm/include/asm/arch-davinci/hardware.h and add RTC_KICK0R_WE, RTC_KICK1R_WE defines, so they are global useable. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com>
2011-12-06omap_gpmc: use SOFTECC in SPL if it's enabledIlya Yanok
Use software ECC for the SPL build if support for software ECC in SPL is enabled. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Acked-by: Scott Wood <scottwood@freescale.com>
2011-12-06nand_spl_simple: add support for software ECCIlya Yanok
This patch adds support for software ECC to the nand_spl_simple driver. To enable this one have to define CONFIG_SPL_NAND_SOFTECC. Tested on OMAP3. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Acked-by: Scott Wood <scottwood@freescale.com>
2011-12-06davinci_emac: hardcode 100Mbps for AM35xx and RMIIIlya Yanok
For some reason code setting the speed based on the PHY feedback causes troubles on AM3517 so hardcode 100Mbps for now. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06davinci_emac: fix for running with dcache enabledIlya Yanok
DaVinci EMAC is present on TI AM35xx SoCs (ARMv7) which run with D-Cache enabled by default. So we have to take care and flush/invalidate the cache before/after the DMA operations. Please note that the receive buffer alignment to 32 byte boundary comes from the old driver version I don't know if it is really needed or alignment to cache line size is enough. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-29 00:28:30 +0000