| Age | Commit message (Collapse) | Author |
|---|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
struct ti_qspi_priv->max_hz is declared as unsigned int, so the following
error path check will always be false, even when "spi-max-frequency"
property is invalid/missing:
priv->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency", -1);
if (priv->max_hz < 0) {
...
}
Replace the fdtdec call with dev_read_u32_default() and use 0 as the
default value. Error out if max_hz is zero.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
|
|
Try to maintain some consistency between these variables by using _plat as
a suffix for them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing
changes made to 56d37f1c564107e27d873181d838571b7d7860e7.
Unfortunately this is causing CI failures:
https://travis-ci.org/github/trini/u-boot/jobs/711313649
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Convert driver to use spi-mem ops in order to support accelerated MMIO
flash interface in generic way and for better performance.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Now that all boards using TI QSPI have moved to DM and DT, drop non DM
code completely.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[jagan: update MIGRATION.txt, rebase config_whitelist.txt]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Fix the divider calculation logic to choose a value so that the
resulting baudrate is either equal to or closest possible baudrate less
than the requested value. While at that, cleanup ti_spi_set_speed().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
This udelay() was added as an HACK and is no longer required. All
read/write/erase operations work fine even without this delay. Hence,
remove the udelay() call.
Tested read/write/erase operation on AM437x SK. Also tested QSPI Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
TI QSPI has four 32 bit data registers which can be used to transfer 16
bytes of data at once. The register group QSPI_SPI_DATA_REG_3,
QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is
treated as a single 128-bit word for shifting data in and out. The bit
at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out
in case of 128 bit transfer mode. Therefore the first byte to be written
to flash should be at QSPI_SPI_DATA_REG_3[31-25] position.
Instead of writing 1 byte at a time when interacting with SPI NOR flash,
make use of all the four registers so that 16 bytes can be transferred
in one go.
With this patch, the flash write speed increases from ~250KBs/ to
~650KB/s on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
As per commit b545a98f5dc563 ("spi: ti_qspi: Add delay
for successful bulk erase) says its added to meet bulk erase timing
constraints. But bulk erase is a cmd to flash and delay in read path
does not make sense. Morever, testing on DRA74/DRA72 evm has shown that
this delay is no longer required.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
clk_div is uninitialized at the beginning of ti_spi_set_speed(), move
debug() print after clk_div calculation to avoid compiler warning and to
have proper value of clk_div printed during debugging.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
Populating QSPI_RD_SNGL bit(0x1) in priv->cmd means that value
QSPI_INVAL (0x4) is not written to CMD field of QSPI_SPI_CMD_REG in
ti_qspi_cs_deactivate(). Therefore CS is never deactivated between
successive READ ID which results in sf probe to fail.
Fix this by not populating priv->cmd with QSPI_RD_SNGL and OR it wih
priv->cmd as required (similar to the convention followed in the
driver).
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
Correcting QSPI disable/unselect CS reset value.
CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8]
This is not causing any issue, but its better
to untouch the reserved bits.
Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
|
|
TI QSPI driver directly typecasts fdt_addr_t to a pointer. This is
not strictly correct, as it gives a build warning when fdt_addr_t is u64.
So, use map_physmem for a proper typecasts.
This is inspired by commit 167efe01bc5a9 ("dm: ns16550: Use an address
instead of a pointer for the uart base")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
When CONFIG_DMA is defined the default spi_flash_copy_mmap() can
handle dma memory copy, so compile out spi_flash_copy_mmap() from
ti_qspi driver when CONFIG_DMA config is defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
ti-qspi driver currently uses 3-byte addressing mode(and opcodes) for
memory-mapped read. This restricts maximum addressable flash size to
16MB.
Enable the 4-byte addressing(and use 4-byte opcode) for memory-mapped
read to allow access to addresses above 16MB.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[vigneshr@ti.com: Re-word commit description]
Signed-off-by: Vignesh R <vigneshr@ti.com>
|
|
adopt ti_qspi driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Prepare driver for DM conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
conversion
Changing the ti_qspi_priv structure and its instance names from
to priv for driver mode conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
To enable memory map in dra7xx, specific chip select must be
written to control module register. But this hard coded to chip
select 1, fixing it by writing the specific chip select value to
control module register.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
SPI_OPM_RX_AS - SPI_RX_SLOW
SPI_OPM_RX_AF - SPI_RX_FAST
SPI_OPM_RX_DOUT - SPI_RX_DUAL
SPI_OPM_RX_QOF - SPI_RX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
SPI_3WIRE is spi mode not spi flags, so this patch fixed
the spi-3wire checking throgh mode instead of flags.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Add dummy readl after invalidating cmd field of QSPI_CMD_REG to ensure
bus sync. Without this device's CS is not deactivated reliably leading
to failure to enumerate flash or failure to set quad enable bit on
Macronix flash present on am437x-sk and am437x-idk evms.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numerical bit shift with BIT macro
in ti_qspi
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Reviewed-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
ti_qspi uses memory map mode for faster read. Enabling DMA will increase
read speed by 3x @48MHz on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Update op_mode_rx flag based on CONFIG_QSPI_QUAD_SUPPORT flag,
instead of platform.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
This patch enables QUAD read mode for qspi to improve the
read performace while loading the binaries from qspi.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
The patch populates the slave data which will be used by flash driver to
set the flash quad enable bit.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
|
|
Bulk erase is not happening properly on dra7 due to erase timing constraints,
add a delay so that erase timing constraints are properly met.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Yebio Mesfin <ymesfin@ti.com>
|
