| Age | Commit message (Collapse) | Author |
|---|
|
Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.
However this driver is only verified with SD memory cards.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
|
|
Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.
So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.
This implementation allows:
* escape unclear and recursive calculations that are currently in use
* use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.
Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.
Test on P5040 and T4240,
Error Log:
=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
Add some descriptions for esdhc register for easily using.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
eSDHC host controller has new register to support SD Spec 3.0.
And the according host controller version was Freescale eSDHC
Version 3.0.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
Old command timeout value was too small and it caused I/O errors which
led to uncompleted read/write/erase operations and filesystem errors.
Timeout adaptation fixes this issue.
Changes in sdhci_send_command() function:
- change timeout variable to static
- increase default command timeout to 100 ms
- add definition of max command timeout value,
which can be redefined in each board config file
- wait for card ready state for max defined time
if it doesn't exceed defined maximum or return COMM_ERR
Once successfully increased timeout value will be used in next function
call. This fix was tested on Goni, Trats, Trats2 boards by testing UMS
on MMC storage.
Changes v2:
- move global variable cmd_timeout into function sdhci_send_command()
- change condition "==" to ">=" when comparing time with timeout
- print information about timeout increasing and card busy timeout
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
To prevent the confusion, use the get_mmc_clk() instead of mmc_clk().
get_mmc_clk() is more exactly name.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
EXT_CSD_ERASE_GROUP_DEF is lost every time after a reset or
power off. Set it if device has enhanced partitions.
Signed-off-by: Oliver Metz <oliver@freetz.org>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
|
|
The patch fixes the improper read and write of sdhci
host control register for sdma transfer.
The problem comes when reading and writing 1 byte long
host control register with the sdhci_readl() and
sdhci_writel(). The misuse of these functions overwrite
the value of the next registers which are in 4 bytes boundary.
This patch replaces four byte register read/write functions
with one byte read/write ones. Beside, it eliminates
unnecessary bit operation. i.e. or-ing zero against a variable.
Signed-off-by: Juhyun (Justin) Oh <Juhyun_Oh@sigmadesigns.com>
|
|
This fixes two issues:
* a descriptor was allocated for every block, while a descriptor can
take 8 blocks
* there was an off-by-one error in the descriptor preparation: there
were two last descriptors, one with length==0
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
|
|
In dwmci_prepare_data, the descriptors are allocated for DMA transfer.
These are allocated using the ALLOC_CACHE_ALIGN_BUFFER. This macro uses
the stack to allocate these descriptors. This becomes a problem if the
DMA transfer continues after the processor leaves the function in which
the descriptors were allocated.
Therefore, I have moved the allocated of the buffers up one level, to
dwmci_send_cmd(). The DMA transfer should be complete when leaving this
function.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
For SPL builds this is just dead code since we'll only need to read.
Eliminating it results in a significant size reduction for the SPL
binary, which may be critical for certain platforms where the binary
size is highly constrained.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
malloc can fail, so we should better check its return value before using it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
If we don't have CONFIG_SPL_LIBCOMMON_SUPPORT defined then stdio
& *printf functions are unavailable & calling them will cause a link
failure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
|
|
Enable 8-bit host capability for HSMMC2 and/or HSMMC3. CONFIG_HSMMC2_8BIT
(for OMAP4/5/DRA7xx) and/or CONFIG_HSMMC3_8BIT (for DRA7xx only) must be
defined in the board header if an 8-bit eMMC device is connected to the
corresponding port.
Fix the "No status update" error that appeared for eMMC devices by
inserting a 20 us delay between writing arguments and command. This
solution has been proposed by Michael Cashwell <mboards@prograde.net>.
A minor cosmetic fix in a comment as well.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
|
|
"mmc_send_cmd: timeout: No status update" error sometimes happens in
omap_hsmmc driver func mmc_send_cmd() when the MMC controller card
identification and selection sequence is executed for eMMC on OMAP4
boards.
It happens due to incorrect execution of CMD line reset procedure
for OMAP4. Because CMD(DAT) lines reset procedures are slightly
different for OMAP3 and OMAP4(AM335x,OMAP5,DRA7xx).
According to OMAP3 TRM:
Set SRC(SRD) bit in MMCHS_SYSCTL register to 0x1 and wait until
it returns to 0x0.
According to OMAP4(AM335x,OMAP5,DRA7xx) TRMs, CMD(DATA) lines reset
procedure steps must be as follows:
1. Initiate CMD(DAT) line reset by writing 0x1 to SRC(SRD) bit in
MMCHS_SYSCTL register (SD_SYSCTL for AM335x).
2. Poll the SRC(SRD) bit until it is set to 0x1.
3. Wait until the SRC(SRD) bit returns to 0x0
(reset procedure is completed).
Unfortunately, at present omap_hsmmc driver has support only for
OMAP3. And as result step #2 is missing for OMAP4(AM335x,OMAP5,DRA7xx).
This sometimes leads to the fact that the waiting loop which is
required in step #3 does not executed, because SRC bit does not set
yet (at the moment of checking a condition of a loop execution).
And as a result this can cause to timeout error when sending a
next command.
In the particular case (working with eMMC witch do not respond to
some SD specific command) due to incorrect reset sequence after
command SD_CMD_SEND_IF_COND which finished with CTO flag within
64 clock cycles, the next command MMC_CMD_APP_CMD leads to a
timeout error within 1s.
So, extend CMD(DATA) lines reset procedure in func
mmc_reset_controller_fsm() by adding the missing step #2 for
OMAP4+/AM335x boards.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
Do not call a memset for unused variable backup every time.
Remove unused variable from function.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
Samsung SoC is supported the WIDE8, even if Controller version is v2.0.
So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
Conflicts:
drivers/serial/serial.c
The conflict above was a trivial case of adding one init
function in each branch, and manually resolved in merge.
|
|
Enable support for high-capacity eMMC and MMC cards. The MXS MMC
driver has no problem with those.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
|
|
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The FTSDC010_DCR_FIFO_RST symbol is conditionally
defined in <faraday/ftsdc010.h> and it is available
available when CONFIG_FTSDC010_SDIO is enabled.
However the actual driver code unconditionally uses
the FTSDC010_DCR_FIFO_RST constant and this causes
build error if CONFIG_FTSDC010_SDIO is not enabled.
The following error happens when compiling for the
adp-ag101 board:
ftsdc010_mci.c: In function 'ftsdc010_request':
ftsdc010_mci.c:178: error: 'FTSDC010_DCR_FIFO_RST' undeclared (first use in this function)
ftsdc010_mci.c:178: error: (Each undeclared identifier is reported only once
ftsdc010_mci.c:178: error: for each function it appears in.)
The patch ensures that the FTSDC010_DCR_FIFO_RST
symbol gets used only if CONFIG_FTSDC010_SDIO is
defined.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Kuo-Jung Su <dantesu@faraday-tech.com>
|
|
Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.
Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.
For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.
We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
|
|
|
|
Conflicts:
spl/Makefile
|
|
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.
Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
|
|
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
This patch fixes a bug related to mmc writes.
When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.
By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.
Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.
Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1: 7798f6dbd5e1a3030ed81a81da5dfb57c3307cac)
Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....
So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Update pbias programming sequence for OMAP5 ES2.0/DRA7
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Conflicts:
common/cmd_fpga.c
drivers/usb/host/ohci-at91.c
|
|
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:
Commit 7b43db92110ec2f15c5f7187a165f2928464966b
drivers/mmc/fsl_esdhc.c: fix compiler warnings
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
