Age | Commit message (Collapse) | Author |
|
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20230119-u-boot-odroid-go-ultra-v1-2-f96bab9db396@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic
- fixup error on efuse commands return
- add documentation on boot flow
|
|
Add support for hardware watchdog timer for Amlogic SoCs.
This driver has been heavily inspired by his Linux equivalent
(meson_gxbb_wdt.c).
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philippe Boos <pboos@baylibre.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This is a preliminary documentation introducing different
boot sequences, and notably the recovery mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220706093649.3261229-1-narmstrong@baylibre.com
|
|
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed trailing whitespaces and fixed sphinx build error]
Link: https://lore.kernel.org/r/20220426052633.3027932-2-adeep@lexina.in
|
|
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220426052633.3027932-1-adeep@lexina.in
|
|
It add documentation on licencing & provides links to the amlogic-boot-fip
pre-built files collections.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The doc used GXL instructions, which couldn't work on GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add documentation bits for the Radxa Zero
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Fix doc/board/amlogic/index.rst:
- Add S905W to S905X column.
- Add JetHub devices to the corresponding columns.
- Fix tabs to spaces for table alignment
Add doc/board/amlogic files:
- jethub-j100.rst
- jethub-j80.rst
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Banana Pi BPI-M5 is a credit card format SBC with the following features:
- Amlogic S905X3 quad core Cortex-A55
- Mali-G31 GPU
- 4GB LPDDR4
- 16GB eMMC flash
- 4 USB 3.0
- 1 GbE ethernet
- HDMI output
- 2x LEDS
- SDCard
- 2.5mm Jack with Stereo Audio + CVBS
- Infrared Received
- ADC Button
- GPIO Button
- 40 pins header + 3pins debug header
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add documentation bits for the Odroid-HC4.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Update the device matrix and add build instructions.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Update the device matrix and add build instructions.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2.rst to q200 MAINTAINERS and added blank lines to fix build]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The build instructions were buggy and changed a little since they
were written.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Update the matrix table with new supported features and
new SoC features to support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
This adds this dynamic switching right before booting Linux
and the configuration steps in the boards documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed warning by replacing min() by min_t()]
|
|
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
|
|
Move the natural text Amlogic board README files to doc/board/amlogic
into reStructuredText and :
- add reStructuredText markup for bash code
- fix secondary titles markup
- move board support into global support matrix
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|