summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2022-04-01ARM: dts: at91: rename sama7g5ek.dts to at91-sama7g5ek.dtsEugen Hristev
In Linux this DT file is named at91-sama7g5ek.dts. Rename it accordingly. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2022-03-28video: Convert CONFIG_VIDEO_BCM2835 to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VIDEO_BCM2835 This is the final ad-hoc CONFIG_VIDEO_... to convert. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Matthias Brugger <mbrugger@suse.com>
2022-03-28video: fsl: colibri_vf: Drop FSL DCU driverSimon Glass
This does not use driver model and is more than two years past the migration date. Drop it. It can be added back later if needed. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28Merge tag 'v2022.04-rc5' into nextTom Rini
Prepare v2022.04-rc5
2022-03-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_LCD_INFO et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_LCD_INFO CONFIG_LCD_LOGO CONFIG_LCD_INFO_BELOW_LOGO CONFIG_LCD_IN_PSRAM Cc: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_ATMEL_LCD et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ATMEL_LCD CONFIG_ATMEL_LCD_BGR555 CONFIG_ATMEL_LCD_RGB565 CONFIG_GURNARD_SPLASH Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_MII_INIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_MII_INIT Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_PHY_RESET_DELAY to KconfigTom Rini
This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_SYS_RX_ETH_BUFFER to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_RX_ETH_BUFFER Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_TFTP_PORT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_TFTP_PORT Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_RMII to KconfigTom Rini
This converts the following to Kconfig: CONFIG_RMII Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_SYS_FAULT_ECHO_LINK_DOWN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_FAULT_ECHO_LINK_DOWN Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25Convert CONFIG_RESET_PHY_R to KconfigTom Rini
This converts the following to Kconfig: CONFIG_RESET_PHY_R Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_ATMEL_LEGACY to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ATMEL_LEGACY Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_AT91_GPIO_PULLUP to KconfigTom Rini
This converts the following to Kconfig: CONFIG_AT91_GPIO_PULLUP Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_AT91SAM9G10EK et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_AT91SAM9G10EK CONFIG_AT91SAM9261EK CONFIG_AT91SAM9G10 Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_AT91SAM9G20EK et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_AT91SAM9G20EK CONFIG_AT91SAM9260EK CONFIG_AT91SAM9G20EK_2MMC Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_AT91SAM9260 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_AT91SAM9260 CONFIG_AT91SAM9G20 CONFIG_AT91SAM9XE CONFIG_AT91SAM9261 CONFIG_AT91SAM9263 CONFIG_AT91SAM9G45 CONFIG_AT91SAM9M10G45 CONFIG_AT91SAM9N12 CONFIG_AT91SAM9RL CONFIG_AT91SAM9X5 CONFIG_SAM9X60 CONFIG_SAMA7G5 CONFIG_SAMA5D2 CONFIG_SAMA5D3 CONFIG_SAMA5D4 These options are already select'd as needed, so we're just cleaning up files here. Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_AM335X_USB0 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_AM335X_USB0 CONFIG_AM335X_USB0_MODE CONFIG_AM335X_USB1 CONFIG_AM335X_USB1_MODE We do this by introducing specific options for static configuration of USB0/USB1 in SPL rather than defining CONFIG_AM335X_USBx_MODE to the enum value being used. Furthermore, with how the code is used now we do not need to have OTG mode exposed as an option here, so remove that. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18imx: Convert some boards to DM_ETHTom Rini
A small number of i.MX6/7 and vf610 boards have not enabled DM_ETH yet. Given the state of the rest of the platform, enable DM_ETH. Cc: Alison Wang <alison.wang@nxp.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Richard Hu <richard.hu@technexion.com> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_ETHPRIME to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_NFS_TIMEOUT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_NFS_TIMEOUT Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_BOOT_RETRY_TIME et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOOT_RETRY_TIME CONFIG_BOOT_RETRY_MIN CONFIG_RESET_TO_RETRY We also introduce CONFIG_BOOT_RETRY to gate these options, and clean up the associated Makefile entry and C code for picking default values of CONFIG_BOOT_RETRY_MIN. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_NET_RETRY_COUNT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_NET_RETRY_COUNT Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_ARP_TIMEOUT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ARP_TIMEOUT Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_ARMV7_SECURE_BASE et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ARMV7_SECURE_BASE CONFIG_ARMV7_SECURE_MAX_SIZE CONFIG_ARMV7_SECURE_RESERVE_SIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18configs: Re-run migrationsTom Rini
As the CI test for stopping platforms from being merged that were defining symbols that had Kconfig entries, a small number of symbols needed to be migrated again. Do so, and catch two cases the README should also have been updated but was not. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18rockchip: rk3328: enable USB mass storage on RenegadeLeonidas-Panagiotis Papadakos
This is very useful to access the LibreComputer eMMC as removable storage from a PC (e.g. like so `ums 0 mmc 0`). It has been tested as working on my Renegade board. Signed-off-by: Leonidas P. Papadakos <papadakospan at gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-03-18rockchip: rk3399: Add support for chromebook_kevinMarty E. Plummer
Add support for Kevin, an RK3399-based convertible chromebook that is very similar to Bob. This patch is mostly based on existing support for Bob, with only minor changes for Kevin-specific things. Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV, so adjust it here in the dts as well. The rk3399-gru-kevin devicetree has an unknown event code reference which has to be defined, set it to the Linux counterpart. The new defconfig is copied from Bob with the diffconfig: DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin" DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb" VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400 VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600 +TARGET_CHROMEBOOK_KEVIN y With this Kevin can boot from SPI flash to a usable U-Boot prompt on the display with the keyboard working, but cannot boot into Linux for unknown reasons. eMMC starts in a working state but fails to re-init, microSD card works but at a lower-than-expected speed, USB works but causes a hang on de-init. There are known workarounds to solve eMMC and USB issues. Cc: Marty E. Plummer <hanetzer@startmail.com> Cc: Simon Glass <sjg@chromium.org> [Alper: commit message, resync config with Bob, update MAINTAINERS, add to Rockchip doc, add Kconfig help message, set regulator] Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2022-03-18rockchip: bob: Enable more configsAlper Nebi Yasak
This patch enables some configs that should be working on the Bob board, based on what is observed to work on the Kevin board. The Bob board uses an Embedded DisplayPort panel compatible with the simple panel and Rockchip eDP drivers. Its backlight is controlled by the Chromium OS Embedded Controller Pulse Width Modulator. Enable these for the board. Also set VIDEO_ROCKCHIP_MAX_{XRES,YRES} to 1280x800, the resolution of its panel. This had to be done for the Kevin board, but it's untested if this is actually necessary for Bob. The Rockchip video driver needs to assert/deassert some resets, so also enable the reset controller. RESET_ROCKCHIP defaults to y for this board when DM_RESET=y, so it's enough to set that. The Bob board has two USB 3.0 Type-C ports and one USB 2.0 Type-A port on its right side. Enable the configs relevant to USB devices so these can be used. This is despite a known issue with RK3399 boards where USB de-init causes a hang, as there is a known workaround. Some other rk3399-based devices enable support for the SoC's random number generator in commit a475bef5340c ("configs: rk3399: enable rng on firefly/rock960/rockpro64"), as it can provide a KASLR seed when booting using UEFI. Enable it for Bob as well. The default misc_init_r() for Rockchip boards sets cpuid and ethernet MAC address based on e-fuse block. A previous patch extends this on Gru boards to set registers related to SoC IO domains as is necessary on these boards. Enable this function and configs for it on Bob. The microSD card slot on this board (and others based on Gru) is connected to a GPIO controlled regulator (ppvar-sd-card-io), which must be operable by U-Boot. Enable the relevant config option to allow this. Bob boards also use the Winbond W25Q64DW SPI flash chip, enable support for Winbond SPI flash chips in the board config so U-Boot can boot with this chip. Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2022-03-16Merge tag 'xilinx-for-v2022.07-rc1' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2022.07-rc1 microblaze: - Add support for reserved memory xilinx: - Update FRU code with MAC reading zynqmp: - Remove double AMS setting - DT updates (mostly for SOMs) - Add support for zcu106 rev 1.0 zynq: - Update nand binding nand: - Aligned zynq_nand to upstream DT binding net: - Add support for ethernet-phy-id mmc: - Workaround CD in zynq_sdhci driver also for ZynqMP - Add support for dynamic/run-time SD config for SOMs gpio: - Add driver for slg7xl45106 firmware: - Add support for dynamic SD config power-domain: - Update zynqmp driver with the latest firmware video: - Add skeleton driver for DP and DPDMA i2c: - Fix i2c to work with QEMU pinctrl: - Add driver for zynqmp pinctrl driver
2022-03-16Merge https://source.denx.de/u-boot/custodians/u-boot-shTom Rini
- Config tweaks to enable the right I2C driver
2022-03-15test/py: Add tests for the erofsHuang Jianan
Add Python scripts to test 'ls' and 'load' commands, as well as test related filesystem functions. Signed-off-by: Huang Jianan <jnhuang95@gmail.com>
2022-03-15Merge tag 'u-boot-stm32-20220315' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-stm mtd: add NAND write protect support to stm32_fmc2_nand stm32mp1 bsec: Add permanent lock write support stm32mp1 bsec: Add dev in function description cmd_stboard: Update test on misc_read() result video: fix the check of return value of clk_set_rate in stm32_ltdc DT: Alignment with kernel v5.17 for stm32mp15 DT: Add USB OTG pinctrl and regulator in SPL for DHCOR DT: Move vdd_io extras into Avenger96 extras DT: Add DFU support for DHCOM recovery ram: stm32mp1: Unconditionally enable ASR psci: Implement PSCI system suspend and DRAM SSR for stm32mp
2022-03-15ARM: dts: stm32: Add DFU support for DHCOM recoveryMarek Vasut
This patch configures U-Boot SPL for DHCOM SoM to permit DFU upload of SPL and subsequent u-boot.itb for recovery or commissioning purposes. The DFU usage procedure is identical to STM32MP1 DHCOR SoM, see commit 3919aa1722a ("ARM: dts: stm32: Add DFU support for DHCOR recovery") , except for switching the SoM into DFU mode. By default, the DHCOM SoM has no dedicated mechanism for setting BOOTn straps into UART/USB mode, therefore to enter DFU mode, the SoC must fail to boot from boot media which can be selected by the BOOTn strap override mechanism first and then fall back to DFU mode. In case of a SoM with pre-populated BOOTn strap override button, power the system off, remove microSD card (if applicable), hold down the BOOTn strap override button located between eMMC and SoM edge connector, power on the SoM. The SoC will fail to boot from SD card and fall back into DFU mode. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-03-14Merge tag 'video-20220314' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-video - fix display of the u-boot logo on Apple devices - convert Nokia RX-51 to CONFIG_DM_VIDEO
2022-03-14Merge tag 'v2022.04-rc4' into nextTom Rini
Prepare v2022.04-rc4
2022-03-14board: tbs2910: Enable Link Time Optimizations in defconfigSoeren Moch
This saves about 12 kBytes image size and helps to stay within the size limit. Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Soeren Moch <smoch@web.de>
2022-03-14vexpress64: fvp: Fix automatic bootAndre Przywara
Commit 90f262a6951f ("vexpress64: Clean up BASE_FVP boot configuration") cleaned up the usage of default address variables, but missed to update the address for the kernel in the FVP's bootcmd definition. Change ${kernel_addr} to read ${kernel_addr_r} to bring back the automated boot for the fastmodel. Also use "setenv" instead of the potentially ambiguous "set" on the way. Fixes: 90f262a6951f ("vexpress64: Clean up BASE_FVP boot configuration") Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-14configs: condor: Enabled I2C support for R-Car V3HNam Nguyen
Enable I2C support for R-Car V3H (R8A77980) on Condor board. Signed-off-by: Nam Nguyen <nam.nguyen.yh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2022-03-14configs: eagle: Enabled I2C support for R-Car V3MNam Nguyen
Enable I2C support for R-Car V3M (R8A77970) on Eagle board. Signed-off-by: Nam Nguyen <nam.nguyen.yh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2022-03-14configs: falcon: Enabled I2C support for R-Car V3UNam Nguyen
Enable I2C support for R-Car V3U (R8A779A0) on Falcon board. Signed-off-by: Nam Nguyen <nam.nguyen.yh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2022-03-12Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-spiTom Rini
- sunXi SPI fixups (Andre) - bcm iproc qspi (Rayagonda)
2022-03-10arm: add initial support for the Phytium Pomelo Boardweichangzheng
This adds platform code and the device tree for the Phytium Pomelo Board. The initial support comprises the UART and the PCIE. Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
2022-03-10configs: j721e_hs_evm_a72_defconfig: Add command for initializing QSGMII PHYAswath Govindraju
QSGMII PHY present on the j721e common processor board requires to be initialized before the core boots up. Therefore, run the corresponding command during boot to do the same. Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2022-03-10configs: j721e_evm_a72_defconfig: Fix the bootcmdAswath Govindraju
Add the command "boot_rprocs" that is required for booting remote processors in U-Boot. Fixes: 5980925e2a5a ("include: configs: j721e_evm: Add support to boot ethfw core in j721e") Reported-by: Jesse Villarreal <jesse.villarreal@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2022-03-10ARM: omap3_beagle: Enable DM_PMIC and DM_REGULATORRomain Naour
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO gives us the ability to better monitor voltages and enable hardware through the device tree. The TL4030 (TPS65950) is not yet migrated to DM, so this patch only enables the fixed and GPIO controlled regulators. Based on commit [1][2]. [1] a40d3cc845756e1e38af5ac31986539417e64abb [2] 2448e42d73fb91e4b56bb41b2677e18ab99a6c83 Signed-off-by: Romain Naour <romain.naour@gmail.com>
2022-03-10ARM: omap3_beagle: Enable PinctrlRomain Naour
The simple pinctrl driver currently available works with the omap3. Enabling this will use the device tree to automatically set the pin-muxing for various drivers. Based on commit: 57dbf754e37d3347cad441f3869bf72c0d726a71 Signed-off-by: Romain Naour <romain.naour@gmail.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-08-17 15:00:44 +0000