summaryrefslogtreecommitdiff
path: root/configs/mvebu_espressobin-88f3720_defconfig
AgeCommit message (Collapse)Author
2021-04-06arm: mvebu: Espressobin: Enable watchdog support but do not start itPali Rohár
Espressobin had disabled watchdog support (CONFIG_WDT) because older stable Linux kernel versions (which are used by current stable OpenWRT and Debian versions) do not have support for Armada 3700 watchdog driver. Therefore they are not able to periodically kick watchdog so Espressobin enter into boot loop. This change enable CONFIG_WDT, CONFIG_WDT_ARMADA_37XX and CONFIG_CMD_WDT options which add support for U-Boot 'wdt' command. And unset new CONFIG_WATCHDOG_AUTOSTART option which cause that watchdog is not automatically started by U-Boot during init phase, like when CONFIG_WDT option is not set at all. So with this change, U-Boot on Espressobin would have working 'wdt' command which can be used from boot scripts (e.g. for enabling watchdog prior new Linux booting kernel). But default behavior of watchdog status stays unchanged, U-Boot does not start watchdog on Espressobin during its init phase. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-03-15configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-03-12arm: mvebu: Espressobin: Enable additional optionsPali Rohár
Enable support for NVMe disks which can be connected to mPCIe slot via M.2 reduction. Enable btrfs and squashfs filesystems which are used by more Linux distributions. And enable fsuuid and setexpr commands which can be useful in scripting. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-02-08arm: mvebu: Espressobin: Set the maximum slave SPI speed to 40MHzKonstantin Porotchkin
While the SPI controller speed is defined by DTS, the maximum slave speed (connected devices) is limited by the pre-defined configuration value CONFIG_SF_DEFAULT_SPEED to 1MHz This patch increases this maximum SPI slave device speed to 40MHz Change-Id: I0d1239bd8a2061c66725c2c227c1e1f49c92c29e Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/59516 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> [pali: Set CONFIG_SF_DEFAULT_SPEED via defconfig] Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2020-10-09configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-05configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-09-24arm: mvebu: Espressobin: Set environment variable fdtfileAndre Heider
Required for the generic distro mechanism. Linux ships with 4 variants: marvell/armada-3720-espressobin-v7-emmc.dtb marvell/armada-3720-espressobin-v7.dtb marvell/armada-3720-espressobin-emmc.dtb marvell/armada-3720-espressobin.dtb Use available information to determine the appropriate filename. Fixes booting GRUB EFI arm64 on Fedora. Reported-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-24arm: mvebu: defconfig: espressobin: enable NET_RANDOM_ETHADDRAndre Heider
The hardware does not provide a MAC address. Enable this so that network access works with just the default environment. Signed-off-by: Andre Heider <a.heider@gmail.com> Acked-by: Konstantin Porotchkin <kostap@marvell.com>
2020-09-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-09-04defconfig: espressobin: Add support for ISSI SPI flashesKonstantin Porotchkin
Enable support of ISSI SPI flashes found on EspressoBIN boards Change-Id: I6de61c48f108fb4f410f321b9db45887d23212e5 Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/61455 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Stefan Chulski <stefanc@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-09-04defconfig: espressobin: Include support for Gigadevice SPIKonstantin Porotchkin
Include support for CONFIG_SPI_FLASH_GIGADEVICE for supporting newly produces EspressoBin boards (v7) Change-Id: I5d4b972cbe2ee5a9d52ce9908794ad4e1b59ee3b Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/61236 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-08-31arm: mvebu: Espressobin: Setup MTD partitions when booting kernelPali Rohár
Due to different partition layouts in different U-Boot versions, DTS for Espressobin in Linux does not contain any definition of MTD partitions. See commit https://git.kernel.org/stable/c/00954566464a4 for more details. This patch via ft_board_setup() hook fills current partition layout used by U-Boot, so booted kernel would see correct MTD partitions layout. U-Boot env partition is calculated from CONFIG_ENV_OFFSET option. First partition contains secure firmware, ARM trusted firmware and U-Boot with checksums. So it is not possible to replace just one image (e.g. U-Boot) without updating other parts where is stored checksum of U-Boot. Therefore there is no extra partition defined for U-Boot and first partition is called just 'firmware'. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm: mvebu: Espressobin: Make SPI env offset compatible with Marvell's U-BootPali Rohár
Espressobin board comes with Marvell's U-Boot version where U-Boot env is stored in SPI at offset 0x3F0000. This patch changes env offset in Espressobin defconfig file to match Marvell's U-Boot version. Users who want to use previous or different env offset can still change it in .config file when compiling U-Boot. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm: dts: a37x0: enable sd card support on espressobinWilson Ding
Enabled SDIO slot 0 (south bridge) for SD card on Espressobin board. Change-Id: I51a2debf9fba276b9c4a2bc6da91328d47f443e3 Signed-off-by: Wilson Ding <dingwei@marvell.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/60945 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> [pali: Define cd-gpios and enable CONFIG_DM_REGULATOR_GPIO] Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm: mvebu: Espressobin: Enable CONFIG_MVNETAPali Rohár
Espressobin uses mvneta ethernet driver. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-10configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTDMiquel Raynal
Like in Linux, just use CONFIG_MTD to compile the MTD stack. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25Convert CONFIG_ARCH_CPU_INIT to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_ARCH_CPU_INIT Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Tested-by: Felix Brack <fb@ltec.ch>
2019-08-02Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_USE_PREBOOT CONFIG_PREBOOT Both are together in one commit, since otherwise the former causes kconfig to define the latter, which gives duplicate symbol errors. Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the backslash lands in the wrong place. Similarly with socfpga_vining_fpga. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-04-29configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-01-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-09configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-29arm64: mvebu: defconfig: enable CONFIG_AHCI_MVEBUKen Ma
This patch enables the new ahci mvebu driver for marvell arm64 platform SOCs(A3k and A8k). And since AHCI_MVEBU selects SCSI_AHCI, so "CONFIG_SCSI_AHCI=y" is removed from those default config files. Signed-off-by: Ken Ma <make@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14treewide: Move CONFIG_PHY_MARVELL to KconfigMario Six
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards already had it in their Kconfig), but had not been moved for older boards. Move it to the defconfigs for all boards. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14spi: mvebu_a3700_spi: Use Armada 37xx clk driver for SPI clock frequencyMarek Behún
Since now we have driver for clocks on Armada 37xx, use it to determine SQF clock frequency for the SPI driver. Also change the default config files for Armada 37xx devices so that the clock driver is enabled by default, otherwise the SPI driver cannot be enabled. Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2018-04-08treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to KconfigMario Six
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-30arm64: a37xx: defconfigs: enable PCI_CMD and E1000 driverKen Ma
Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30arm64: a37xx: defconfigs: enable aardvark pcie driverWilson Ding
Signed-off-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30arm64: a37xx: defconfig: Enable PINCTRL and GPIO support for ESPRESSOBin boardKen Ma
This patch enable the PINCTRL and GPIO support, including the GPIO command on the Armada 3720 espressobin board. Reviewed-on: http://vgitil04.il.marvell.com:8080/40746 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-02-11configs: Migrate CONFIG_SYS_TEXT_BASETom Rini
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-10configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-05cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGATuomas Tynkkynen
cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-01-09arm64: a37xx: defconfigs: enable CONFIG_DISTRO_DEFAULTSAndre Heider
Signed-off-by: Andre Heider <a.heider@gmail.com> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2017-12-12ata: Migrate CONFIG_SCSI_AHCI to KconfigTuomas Tynkkynen
And use 'imply' liberally. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-09-08usb: net: migrate USB Ethernet adapters to KconfigChris Packham
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08usb: net: migrate CONFIG_USB_HOST_ETHER to KconfigChris Packham
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-08 11:53:39 +0000