summaryrefslogtreecommitdiff
path: root/configs/am64x_evm_a53_defconfig
AgeCommit message (Collapse)Author
2024-03-21configs: am64x_evm_a53: Enable ICSSG DriverMD Danish Anwar
Enable ICSSG driver, DP83869 phy driver, REMOTEPROC and PRU_REMOTEPROC in am64x_evm_a53_defconfig. All these configs are needed for ICSSG driver. Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
2024-03-21configs: am6*_a53: Enable 'ddrss' ECC test commandSanthosh Kumar K
Enable CONFIG_TI_COMMON_CMD_OPTIONS and CONFIG_CMD_DDRSS to use the 'ddrss' command for testing ECC. Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
2023-12-06configs: am64x_evm_a53_defconfig: Fix USB DFU bootRoger Quadros
Increasing SPL_STACK_R_MALLOC_SIMPLE_LEN to 16M seems to break USB DFU boot. The default of 4M seems to be OK for NAND case as well so stick to defaults. Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com> Fixes: b1ba64d9bab0 ("configs: am64x_evm_a53_defconfig: add SPL_LOAD_FIT_APPLY_OVERLAY") Signed-off-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Judith Mendez <jm@ti.com> Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
2023-11-24configs/am64x_evm_a53_defconfig: Enable NAND DFURoger Quadros
Enable NAND support for DFU. Signed-off-by: Roger Quadros <rogerq@kernel.org>
2023-11-24configs: am64x_evm_a53_defconfig: Enable NANDRoger Quadros
Enables configuration required for NAND in SPL and u-boot. Enable MTD Driver model and MTD + UBI command line utilities. Add mtdids/mtdparts for NAND as it is required for u-boot's MTD subsystem commands to recognize NAND partitions. Add u-boot partition location. Signed-off-by: Roger Quadros <rogerq@kernel.org>
2023-11-24configs: am64x_evm_a53_defconfig: add SPL_LOAD_FIT_APPLY_OVERLAYRoger Quadros
We want SPL to apply DTB overlays (e.g. NAND card overlay) so enable SPL_LOAD_FIT_APPLY_OVERLAY. Increase SPL_LOAD_FIT_APPLY_OVERLAY_BUF_SZ and SPL_STACK_R_MALLOC_SIMPLE_LEN. Without this SPL hangs. Signed-off-by: Roger Quadros <rogerq@kernel.org>
2023-11-22configs: am64x_evm_r5/a53_defconfig: Fix eMMC raw boot offsetsJudith Mendez
EMMC boot is broken for AM64x platform. This is due to the size of tiboot3.bin growing beyond the 500KB of memory allocated in eMMC. There was effort to move the offsets and give more space to tiboot3.bin, but the offsets in defconfig were not updated. Update offsets in defconfig to load each binary from the correct adress in eMMC according to the following eMMC layout: boot0/1 partition 0x0+----------------------------------+ | tiboot3.bin (1 MB) | 0x800+----------------------------------+ | tispl.bin (2 MB) | 0x1800+-----------------------------------+ | u-boot.img (4 MB) | 0x3800+-----------------------------------+ | environment (128 KB) | 0x3900+-----------------------------------+ Signed-off-by: Judith Mendez <jm@ti.com>
2023-10-18configs: am64x_evm_a53_defconfig: Enable R5F remote proc supportHari Nagalla
Add support for R5F remote proc driver. Signed-off-by: Hari Nagalla <hnagalla@ti.com>
2023-07-07configs: k3: Remove saved environmentsManorit Chawdhry
Having saved environments usually causes inconsistencies while in development workflow. The saved environments conflict with the default ones that U-boot should be updating during development but that doesn't happen and the saved environments need to be reset during bootups to test the changes causing extra debugs. Remove the saved environments as a default. Environments can always be re-enabled locally if one does like them or needs them for some production environment. Optionally, Uenv.txt can also be used on some of the boot media. Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
2023-07-06configs: am64: Fix booting of fitImage on AM64xKamlesh Gurudasani
fitImage needs to be processed by U-boot and not tifs. Remove CONFIG_FIT_IMAGE_POST_PROCESS option. Do not limit the maximum size of the buffer that is used to decompress the OS image in to, this causes issue while inflating the image, if image size is greater than the buffer. Remove CONFIG_SYS_BOOTM_LEN Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
2023-07-06configs: am64x_evm_*_defconfig: Enable OSPI boot supportVignesh Raghavendra
Add configs to support flashing/reading and booting from OSPI flashes. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2023-07-06configs: am64x_evm_a53_defconfig: Enable I2C GPIO driversRoger Quadros
We need the I2C GPIO drivers to detect expansion cards. Signed-off-by: Roger Quadros <rogerq@kernel.org>
2023-06-23configs: k3: make consistent bootcmd across all k3 socsKamlesh Gurudasani
Default to common bootcmd that is set across all k3 devices. Tested-by: Nikhil M Jain <n-jain1@ti.com> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com> Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
2023-06-22Kconfig: Default malloc size to 32MB for ARCH_K3Vignesh Raghavendra
This allows us to download large images like linux kernel and flash it to boot media. Drop from defconfigs so that its common across platform. Note the some *_r5_*defconfigs set this to even higher value but thats useless as ARCH_K3 doesn't use u-boot.img for R5. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2023-06-05configs: am6*_a53_defconfig: Enable CMD_GPIOVignesh Raghavendra
This allows to toggle GPIOs for debug and testing. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2023-04-10configs: am64x_evm_*_defconfig: Enable HS supportVignesh Raghavendra
Enable TI_SECURE_DEVICE and FIT_IMAGE_POST_PROCESS to support HS device boot Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2023-03-27configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2023-02-17configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-10-21configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07Convert CONFIG_SYS_BOOTM_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_BOOTM_LEN As part of this, rework error handling in boot/bootm.c so that we pass the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not be available to host tools but we do know the size that we passed to malloc(). Cc: Soeren Moch <smoch@web.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_SPL_MALLOC_START We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to control if we have a malloc pool or not. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_BSS_START_ADDR to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.hTom Rini
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_BSS_MAX_SIZE et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_PAD_TO et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_FS_LOAD_PAYLOAD_NAME et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_FS_LOAD_ARGS_NAME CONFIG_SPL_FS_LOAD_KERNEL_NAME CONFIG_SPL_FS_LOAD_PAYLOAD_NAME Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SYS_MAXARGS to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-09config: enable TPS65219 for am64x_evm_a53 boardsNeil Armstrong
The E4 revision of the AM64 SKEVM embeds a TPS65219 PMIC, this enables the necessary options to load and control the PMIC regulators. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2022-04-22configs: Resync with savedefconfigTom Rini
Resync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-04configs: am64x_evm_a53_defconfig: Switch to per-cpu timer as tick providerVignesh Raghavendra
On arm64 systems, recommendation is to use per-cpu timer for time keeping. Currently AM64 ends up using DM timer as tick timer as driver is enabled in the config. Drop OMAP DM Timer related configs, this will switch to using armv8 per-cpu timer as tick timer for A53 SPL/U-Boot. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-By: Nishanth Menon <nm@ti.com>
2022-01-31configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-01-28configs: am64x_evm_r5/a53_defconfig: Enable configs required for EthbootVignesh Raghavendra
Enable config options needed to support Ethernet boot on AM64x SK. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2021-12-27configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-17configs: am64x_evm_*_defconfig: Add configs to enable serdes for USB 3.0 supportAswath Govindraju
Add configs to enable serdes for USB 3.0 support. Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-11-01configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-15configs: Resync with savedefconfigTom Rini
Resync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-04spi: Rename SPI_SUPPORT to SPISimon Glass
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-04serial: Rename SERIAL_SUPPORT to SERIALSimon Glass
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-04mmc: Rename MMC_SUPPORT to MMCSimon Glass
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> [trini: Fixup some incorrect renames] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-31Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-10configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-29Merge tag 'ti-v2021.10-rc2' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-ti - Add MMC High speed modes for AM64 and J7200 - Add Sierra/Torrent SERDES driver - Minor clean-ups for R5F boot from SPL
2021-07-28i2c: Rename SPL/TPL_I2C_SUPPORT to I2CSimon Glass
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-28Rename DRIVERS_MISC_SUPPORT to DRIVERS_MISCSimon Glass
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-28Rename SPL_USB_HOST_SUPPORT to SPL_USB_HOSTSimon Glass
Rename this option so that CONFIG_IS_ENABLED can be used with it. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-27configs: am64x_evm_*_defconfig: Enable config to support gpt and FDT library ↵Aswath Govindraju
overlay Enable config to support gpt command on AM642 evm/sk and enable config for FDT library overlay support Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210726152807.22991-7-a-govindraju@ti.com
2021-07-27configs: am64x_evm_*_defconfig: Enable configs to support eMMC bootKishon Vijay Abraham I
Enable configs to support eMMC boot. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210726152807.22991-6-a-govindraju@ti.com
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-29 01:38:27 +0000