summaryrefslogtreecommitdiff
path: root/configs/am57xx_hs_evm_defconfig
AgeCommit message (Collapse)Author
2023-02-23Revert "configs: am57xx_evm: Enable Android commands"Praneeth Bajjuri
This reverts commit 7d9dbeafe637a25267f0902ead02f61843edb7f3. commit 7988f626336a ("common: avb_verify: Add CONFIG_AVB_PUBKEY_FILE to specify the root avb public key") was introduced to support AVB on am62x android. But this broke am57x builds. Android on am57xx is not validated currently hence reverting the patch till a right fix is identified that scales to all supported platforms. Signed-off-by: Praneeth Bajjuri <praneeth@ti.com> Reported-by: Ryan Eatmon <reatmon@ti.com> Suggested-by: Andrew Davis <afd@ti.com>
2021-06-23ARM: DRA7: Enable OPP_HIGH for GPU voltage domainSubhajit Paul
Enable the OPP_HIGH configuration for GPU voltage domain by default for various TI DRA7xx and AM57xx boards. This is being done to meet the performance needs of 1080p GFX/MultiMedia usecases. This domain does not support DVFS and the kernel will continue to run at the boot OPP chosen here. Based on logic similar to that of DSPEVE and IVA voltage domains in commit 58a8921fe34fd5 ("ARM: DRA7: Enable OPP_HIGH for DSPEVE and IVA voltage domains") Signed-off-by: Subhajit Paul <subhajit_paul@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com>
2021-06-23ARM: DRA7: Enable OPP_HIGH for DSPEVE and IVA voltage domainsSuman Anna
Enable the OPP_HIGH configuration for DSPEVE and IVA voltage domains by default for various TI DRA7xx and AM57xx boards. This is being done to meet the performance needs of 1080p MultiMedia usecases and other DSP usecases. These domains do not support DVFS and the kernel will continue to run at the boot OPPs chosen here. Signed-off-by: Suman Anna <s-anna@ti.com>
2020-10-09configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-10configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-08Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28Makefile: Allow CONFIG_SPL_FIT_GENERATOR to be emptySimon Glass
At present we use the empty string to indicate that there is no FIT generator, but this doesn't allow an individual board to undefine it. Create a separate bool instead. Update the config of the boards which currently have an empty string. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-28Convert CONFIG_BOOTP_SEND_HOSTNAME to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_SEND_HOSTNAME Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-29spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI*Lukasz Majewski
This change allows more fine tuning of driver model based SPI support in SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI support in SPL and TPL via Kconfig option. Before this change it was necessary to use: /* SPI Flash Configs */ #if defined(CONFIG_SPL_BUILD) #undef CONFIG_DM_SPI #undef CONFIG_DM_SPI_FLASH #undef CONFIG_SPI_FLASH_MTD #endif in the ./include/configs/<board>.h, which is error prone and shall be avoided when we strive to switch to Kconfig. The goal of this patch: Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL). Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must still support non DM driver. Another use case is the conversion of non DM/DTS SPI driver to support DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the distinction is needed in Kconfig (also if SPL version of the driver supports OF_PLATDATA). In the end of the day one would have to support following use cases (in single driver file - e.g. mxs_spi.c): - U-Boot proper driver supporting DT/DTS - U-Boot proper driver without DT/DTS support (deprecated) - SPL driver without DT/DTS support - SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to run full blown DT/DTS) - SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained environment with no fitImage and OF_LIBFDT support). Some boards do require SPI support (with DM) in SPL (TPL) and some only have DM_SPI{_FLASH} defined to allow compiling SPL. This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI) and provides corresponding defines in Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Tested-by: Adam Ford <aford173@gmail.com> #da850-evm Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> [trini: Fixup a few platforms] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-26spi: Enable missing CONFIG_SPL_DM_SPI supportTom Rini
Due to how the Makefile logic is we currently get DM_SPI support in SPL enabled by having DM_SPI enabled for full U-Boot but not having CONFIG_SPL_DM_SPI set. Add this missing option to boards that were inadvertently making use of it. Cc: Adam Ford <aford173@gmail.com> Cc: Akash Gajjar <akash@openedev.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Andy Yan <andy.yan@rock-chips.com> Cc: Anup Patel <anup.patel@wdc.com> Cc: Atish Patra <atish.patra@wdc.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Chee Hong Ang <chee.hong.ang@intel.com> Cc: Chin-Liang See <clsee@altera.com> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Cc: Heiko Schocher <hs@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Klaus Goger <klaus.goger@theobroma-systems.com> Cc: Levin Du <djw@t-chip.com.cn> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Luca Ceresoli <luca@lucaceresoli.net> Cc: Marek Vasut <marex@denx.de> Cc: Michal Simek <monstr@monstr.eu> Cc: Mike Looijmans <mike.looijmans@topic.nl> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Pavel Machek <pavel@denx.de> Cc: Peter Robinson <pbrobinson@gmail.com> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Cc: Suniel Mahesh <sunil@amarulasolutions.com> Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Wolfgang Grandegger <wg@aries-embedded.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2020-06-26Convert CONFIG_BOOTP_DNS2 to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOOTP_DNS2 CONFIG_BOOTP_PXE_CLIENTARCH Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-04configs: am57xx_evm: Enable Android commandsSam Protsenko
Enable Android commands that will be needed for Android 10 boot flow implementation, for all AM57x variants. Commands enabled: 1. 'abootimg': - CONFIG_CMD_ABOOTIMG=y 2. 'ab_select': - CONFIG_ANDROID_AB=y - CONFIG_CMD_AB_SELECT=y 3. 'avb': - CONFIG_LIBAVB=y - CONFIG_AVB_VERIFY=y - CONFIG_CMD_AVB=y While at it, resync defconfig files with "make savedefconfig". Signed-off-by: Sam Protsenko <joe.skb7@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-15Kconfig: Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMAVignesh Raghavendra
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use macros such as CONFIG_IS_ENABLED() that allow conditional compilation of code for SPL and U-Boot. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-01-10dtimg/am57xx_evm_defconfig: Rename dtimg to adtimgEugeniu Rosca
Rename the existing 'dtimg' command to 'adtimg', in order to: - Suggest the Android origins and scope - Be consistent with the upcoming 'abootimg' command (naming suggested by Simon [*]) The change in _not_ backward compatible, but its benefits outweigh its downsides, given that we don't expect active users of 'dtimg' today. Perform the rename in several steps: 1. Rename *.c file and Kconfig symbol. This should allow 'git log --follow' to properly track the history of 'adtimg.c' 2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c' ELF comparison [**] before and after shows no functional change. [*] https://patchwork.ozlabs.org/patch/1182212/#2291600 [**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o) Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Glass<sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2019-12-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04mtd: ensure MTD is compiled when there is a SPI NOR flash using MTDMiquel Raynal
MTD must be enabled when there is a SPI NOR flash using the SPI_FLASH_MTD config entry. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENTTom Rini
Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25Convert CONFIG_SYS_SPI_U_BOOT_OFFS to KconfigHannes Schmelzer
This converts the following to Kconfig: CONFIG_SYS_SPI_U_BOOT_OFFS Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> [trini: Expose this for SPL_SPI_SUNXI for now] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-31configs: am57xx_evm_defconfig: Enable 'dtimg' commandSam Protsenko
We are going to implement DTBO partition for BeagleBoard X15 further. To support this, 'dtimg' command must be enabled. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2019-07-31configs: am57xx_evm_defconfig: Enable 'bcb' commandSam Protsenko
It is essential to have an access to BCB area of 'misc' partition on Android devices [1]. For BeagleBoard X15 the 'bcb' command will be further used for reboot reason implementation and booting to recovery. It can be also used for debugging reasons, like checking RescueParty messages in BCB area. [1] doc/android/bcb.txt Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-04-29configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-02-18configs: Enable CONFIG_BLK in am57xx_evm and am57xx_hs_evmJean-Jacques Hiblot
Enable CONFIG_DM_SCSI and CONFIG_BLK. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-02-09defconfigs: am57xx_hs_evm: Sync HS and non-HS defconfigsAndrew F. Davis
Additions have been made to the non-HS defconfig without the same being made to the HS defconfig, sync them. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-02-07configs: Don't use SPI_FLASH_BAR as defaultVignesh R
Now that new SPI NOR layer uses stateless 4 byte opcodes by default, don't enable SPI_FLASH_BAR. For SPI controllers that cannot support 4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c, renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to not break functionality. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-01-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-10Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
- DM_I2C_COMPAT removal for all ti platforms from Jean-Jacques Hiblot - Fix in i2c command help output from Chirstoph Muellner.
2018-12-10configs: am335x: am57x: dra7x: Enable CONFIG_SPL_DM_SEQ_ALIASJean-Jacques Hiblot
Those platforms need CONFIG_SPL_DM_SEQ_ALIAS because they enable both DM_I2C and SPL_DM. Without CONFIG_SPL_DM_SEQ_ALIAS, it is not possible to get the I2C bus with i2c_get_chip_for_busnum(). Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Felix Brack <fb@ltec.ch> Tested-by: Felix Brack <fb@ltec.ch> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-07configs: am57xx_evm: Enable DM_USB and DM_USB_DEVJean-Jacques Hiblot
Enable DM_USB and DM_USB_DEV for AM57xx based boards. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-11-13configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-26configs: am57xx: change default board name to beagle_x15Praneeth Bajjuri
beagleboard x15 is the first supported platform variant of am57xx in AOSP (android open source project) now. changing board name to stay in consistent with aosp target name. Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
2018-08-17Convert CONFIG_MISC_INIT_R to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-30usb: fastboot: Convert USB f_fastboot to shared fastbootAlex Kiernan
Convert USB fastboot code to use shared fastboot protocol. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-30fastboot: Move fastboot to drivers/fastbootAlex Kiernan
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to drivers/fastboot. Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing behaviour. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-27Convert CONFIG_SPI to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-11spl: spi: Move CONFIG_SPL_SPI_LOAD to KconfigMarek Vasut
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-24 12:17:12 +0000