| Age | Commit message (Collapse) | Author |
|---|
|
These tests come from Chrome OS code. They are not particularly tidy but can
be useful for checking that the TPM is behaving correctly. Some knowledge of
TPM operation is required to use these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Add a command to display basic information about a TPM such as the model and
open/close state. This can be useful for debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Rather then crashing when there is no data, print an error. The error is
printed by the caller to parse_byte_string().
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
When a 'tpm' command fails, we set the return code but give no indication
of failure. This can be confusing.
Add an error message when any tpm command fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
I2C chips can support a register offset, with registers accessible by
sending this offset as the first part of any read or write transaction.
Most I2C chips have a single byte offset, thus the offset length is 1.
This provides access for up 256 registers.
However other offset lengths are supported, including 0.
Add a command to provide access to the offset length from the command
line. This allows the offset length to be read or written.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Add driver model support to the TPM command and the TPM library. Both
support only a single TPM at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Add new Kconfig options for TPMs in preparation for moving boards to use
Kconfig for TPM configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The set_default_env() function from env_common.c expects either
a fully formatted error msg, e.g.: "## Resetting to default environment\n"
or an error msg prefixed with an !, in which case it will format it.
Fix the init_mmc_for_env() error messages to be prefixed with a !
this changes the bootup-log on sunxi when no mmc card is found from:
MMC: SUNXI SD/MMC: 0
No MMC card foundIn: serial
Out: serial
To:
MMC: SUNXI SD/MMC: 0
*** Warning - No MMC card found, using default environment
In: serial
Out: serial
Which clearly is how things should look.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This should use the align parameter, not bytes. Natural alignment is one
use case but should not be the only one supported by this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add nds32 ag101p generic board support.
Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>
|
|
GCC 5.1 starts warning for comparisons such as !a > 0, assuming that the
negation was meant to apply to the whole expression rather than just the
left operand.
Indeed the comparison in the FIT loadable code is confusingly written,
though it does end up doing the right thing. Rewrite the condition to be
more explicit, that is, iterate over strings until they're exhausted.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Move x86_fsp_init() call after initf_malloc() so that we can fix up
the gd->malloc_limit later.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.
The fix is not complicated but it seems safer to revert this for now.
This reverts commit 2afddae07523f23f77acd066ad1719f53d289f98.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Use memalign() with ARCH_DMA_MINALIGN to allocate read buffers.
This is required because, flash drivers may use DMA for read operations
and may have to invalidate the buffer before read.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
|
|
Use memalign() with ARCH_DMA_MINALIGN to allocate read buffers.
This is required because, flash drivers may use DMA for read operations
and may have to invalidate the buffer before read.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
|
|
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present we have a simple assignment to gd. With some archs this is
implemented as a register or through some other means; a simple assignment
does not suit in all cases.
Change this to a function and add documentation to describe how this all
works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Some archs like to have larger alignment for their global data. Use 16 bytes
which suits all current archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
bd->bi_dram[] has both start address and size defined as 32-bit,
which is not the case on some platforms where >=4GiB memory bank
is used. Change them to support such memory banks.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This fixes the following warning (and the runtime error reporting):
../common/image-fdt.c:491:4: warning: 'fdt_ret' may be used
uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Allow showing custom board info from a checkboard() function being
implemented if CONFIG_CUSTOM_BOARDINFO is specified. Previously the
device tree model was always displayed not taking any
CONFIG_CUSTOM_BOARDINFO into account.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The following commit changed the order of the column vs. row parameter
to the lcd_init_console() function but missed actually changing it as
well the second time it is called from lcd_clear() which resulted in a
garbled text console which this patch fixes.
commit 604c7d4a5a3cf70949f6e6094bf0d52ee3b4804d
common/lcd_console: introduce display/framebuffer rotation
Tested on Colibri T20 with my latest assortment of tegra
fixes/enhancements patch set.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Modify the data pointer type from ulong* to u32*.
For arm64 type "ulong" could be 64-bit. Then in line 89 of common/cmd_source.c:
"while (*data++);" data will point to the next 64 bits each time. As the uImage
file generated by mkimage tool keeps the same data format in either 32-bit or 64-bit
platform, the difference would cause failure in 64-bit platform.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
|
|
Make the cast explicit for "warning: cast to pointer from integer of different size".
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
|
|
If a dtb is specified on the command-line, the Android boot image ramdisk
will not be found. Fix this so that we can specify the ramdisk address and
dtb address. The syntax is to enter the Android boot image address for
both the kernel and ramdisk.
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This patch enables building SPL without
CONFIG_SPL_SERIAL_SUPPORT support.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Ensure we build arch/arm/imx-common on mx28]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When a regulator command cannot honour the requested voltage, display the
limits to try to be helpful.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
|
|
The following commit enforces CONFIG_DM_ETH for USB Ethernet which
breaks any board using CONFIG_USB_HOST_ETHER without CONFIG_DM_ETH
which this patch fixes.
commit 69559093f6173dcfcb041df0995063bdbd07d49b
dm: usb: Avoid using USB ethernet with CONFIG_DM_USB and no DM_ETH
Tested on Colibri T20/T30 as well as Apalis T30 with
CONFIG_USB_HOST_ETHER and CONFIG_USB_ETHER_ASIX enabled and a LevelOne
USB-0301 ASIX AX88772 dongle.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
The code in question polls an USB port status via USB_REQ_GET_STATUS
to determine whether there is a device on the port or not. The way to
figure that out is to check two bits. Those are wPortChange[0] and
wPortStatus[0].
The wPortChange[0] indicates whether some kind of a connection status
change happened on a port (a device was plugged or unplugged). The
wPortStatus[0] bit indicates the status of the connection (plugged or
unplugged).
The current code tests whether wPortChange[0] == wPortStatus[0] and
if that's the case, considers the loop polling for the presence of a
USB device on port finished.
This works for most USB sticks, since they come up really quickly and
trigger the USB port change detection before the first iteration of the
detection loop happens. Thus, both wPortChange[0] and wPortStatus[0]
are set to 1 and thus equal. The loop is existed in it's first iteration
and the stick is detected correctly.
The problem is with some obscure USB sticks, which take some time before
they pop up on the bus after the port was enabled. In this case, both
the wPortChange[0] and wPortStatus[0] are 0. They are equal again, so
the loop again exits in the first iteration, but this is incorrect, as
such USB stick didn't have the opportunity to get detected on the bus.
Rework the code such, that it checks for wPortChange[0] first to test
if any connection change happened at all. If no change occured, keep
polling. If a change did occur, test the wPortStatus[0] to see there is
some device present on the port and only if this is the case, break out
of the polling loop.
This patch also trims down the duration of the polling loop from 10s
per port to 1s per port. This is still annoyingly long, but there is
no better option in case of U-Boot unfortunatelly. This change will
most likely increase the duration of 'usb start' on some platforms,
but this is needed to fix a bug.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
|
|
The EFI memory map is passed from the stub to U-Boot in a table. Add a
command to display it in a vaguely readable fashion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on QEMU
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When running U-Boot as an EFI application we cannot relocate since we do not
have relocation information. U-Boot has already been relocated to a suitable
address.
Add a global_data flag to control skipping relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When U-Boot runs as an EFI application is does not have a definition of
CONFIG_SYS_TEXT_BASE. U-Boot is a relocatable application and the relocation
is done by EFI. U-Boot can be loaded at any address.
This is similar to how sandbox works. Adjust the early board init to deal
with this.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add '\n' for debug msg.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Do not print confusing "Board: Unknown" during boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
Use one command for showing overall CPU status than several without
knowing how many cpus is available in the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The sysboot and pxe commands currently support either U-Boot formats or
raw zImages. Add support for the AArch64 Linux port's native image format
too.
As with zImage support, there is no auto-detection of the native image
format. Rather, if the image is auto-detected as a U-Boot format, U-Boot
will try to interpret it as such. Otherwise, U-Boot will fall back to a
raw/native image format, if one is enabled.
My belief is that CONFIG_CMD_BOOTZ won't ever be enabled for any AArch64
port, hence there's never a need to differentiate between CONFIG_CMD_
_BOOTI and _BOOTZ at run-time; compile-time will do. Even if this isn't
true, we want to prefer _BOOTI over _BOOTZ when defined, since _BOOTI is
definitely the native format for AArch64.
Change-Id: I83c5cc7566032afd72516de46f4e5eb7a780284a
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
property
In case of enable CONFIG_OF_CONTROL and has a "model" property in the root node,
the board special "checkboard" will not be called.
Usually we show some useful version information in the function.
This patch enable call "checkboard" in any case.
It is not conflicting with showing "model" at the same time.
For example on LS2085AQDS:
Showing "model" only:
Model: Freescale Layerscape 2085a QDS Board
Showing "checkboard" only:
Board: LS2085E-QDS, Board Arch: V1, Board version: B, boot from vBank: 4
Showing both:
Model: Freescale Layerscape 2085a QDS Board
Board: LS2085E-QDS, Board Arch: V1, Board version: B, boot from vBank: 4
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
This patch introduces the option to boot from a MMC card parition with
an offset. This can be done by using both defines together:
define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR ((160 << 10) / 512)
The example above loads the main U-Boot at offset 160KiB from the MMC
partition 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
Since we're now using a dynamic controller index for fastboot too,
usb_gadget_handle_interrupts should be using it instead of 0 (despite the fact
that it's currently not being used at all in the musb-new implementation).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
Each USB download function command calls board_usb_init before registering the
USB gadget and board_usb_cleanup after de-registering it. On devices currently
using fasboot, musb-new is usually initialized earlier, but some other boards
might need the board_usb_init call to properly initialize musb-new.
This requires adding an argument (the USB controller index) to the fastboot
command, as it is currently done with other USB download gadget functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
|
|
In Linux USB_DEVICE() is used to declare a USB device by vendor/device ID.
We should follow the same convention in U-Boot. Rename the existing
USB_DEVICE() macro to U_BOOT_USB_DEVICE() and bring in the USB_DEVICE()
macro from Linux for use in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
