Age | Commit message (Collapse) | Author |
|
Patch by Stefan Roese, 12 Sep 2006
|
|
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
|
|
|
|
|
|
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
|
|
Also bumped up ABI version to reflect this change.
|
|
Patch by Stefano Babic, 31 Aug 2006
|
|
|
|
|
|
This bug will cause the kernel booting to pause a long time.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
(cherry picked from 2f15776ccc6dc32377d8ba9652b8f58059c27c6d commit)
|
|
|
|
This bug will cause the kernel booting to pause a long time.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
|
|
Signed-off-by: Matthew McClintock <msm@freescale.com>
|
|
|
|
Add AHCI support in u-boot, enable the sata disk controllers which
following the AHCI protocol.
Signed-off-by:Jason Jin<jason.jin@freescale.com>
|
|
|
|
Signed-off-by: Matthew McClintock <msm@freescale.com>
|
|
Signed-off-by: Matthew McClintock <msm@freescale.com>
|
|
|
|
|
|
|
|
|
|
Signed-off-by: Matthew McClintock <msm@freescale.com>
|
|
Signed-off-by: Matthew McClintock <msm@freescale.com>
|
|
Patch by Heiko Schocher, 15 Aug 2006
|
|
|
|
Conflicts:
include/ft_build.h
include/pci.h
Resolved, though.
|
|
Matthew McClintock 26-June-2006
|
|
Matthew McClintock 26-June-2006
|
|
|
|
|
|
Properly pass break code back from readline.
Patch by Roger Blofeld, 31 Jul 2006
|
|
Patch by Stefan Roese, 07 Aug 2006
|
|
|
|
problems with some USB storage devices. Some code readability improvements.
|
|
Patch by Stefan Roese, 27 Jul 2006
|
|
|
|
|
|
Patch by Ladislav Michl, 14 Sep 2005
|
|
|
|
Patch by JinHua Luo, 01 Sep 2005
|
|
Problem pointed out by Andrew Dyer, 13 Jun 2005
|
|
- Support for TQM5200S (short version without graphic controller)
- Support for modules with 'N' type S29GL128N Spansion flashes
(requires changes to flash layout)
- Support for MPC5200B cpu (mostly support for second SDRAM bank)
|
|
|
|
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by:Jason Jin <Jason.jin@freescale.com>
|
|
|
|
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
|
|
|
|
when booting filesystem from ramdisk.
Signed-off-by:Jason Jin <Jason.jin@freescale.com>
|