summaryrefslogtreecommitdiff
path: root/board/toradex
AgeCommit message (Collapse)Author
2020-03-04board: apalis_imx6: Add KSZ9131 phy skew settingsPhilippe Schenker
This patch adds skew register settings for KSZ9131. It checks first which phy is on the board and then applies the correct skew settings. Skew settings calculation for the KSZ9131: The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All PCB traces where routed exactly the same length so we can calculate the skew settings without taking the length into consideration. RXC skew (PHY to MAC): - We use the 2ns DLL controlled delay on the PHY - We do not use the skew registers This results in the following values: RXC PHY fixed Delay 2000ps PHY Added Delay 0ps T_setup_R min 2.00ns T_setup_R typ 2.00ns T_setup_R max 2.00ns T_hold_R min 1.60ns T_hold_R typ 2.00ns T_hold_R max 2.40ns That means we are well within RGMII specs. TXC skew (MAC to PHY): - We use the 2ns DLL controlled delay on the PHY - We then substract ~0.6ns with TXD[0:3] and TXC clock pad skew register in a resulting ~1.4ns delay. This results in the following values under consideration of the tolerances: TXC min TXC typ TXC max MAC min -100ps -100ps -100ps MAC max 900ps 900ps 900ps PHY fixed Delay 2000ps 2000ps 2000ps PHY added Delay -340ps -600ps -859ps T_setup_T min 1.56ns 1.30ns 1.04ns T_setup_T typ 2.06ns 1.80ns 1.54ns T_setup_T max 2.56ns 2.30ns 2.04ns T_hold_T min 1.04ns 1.30ns 1.56ns T_hold_T typ 1.94ns 2.20ns 2.46ns T_hold_T max 2.84ns 3.10ns 3.36ns This shows that T_hold_T min and T_setup_T min times are out of spec for RGMII timing. However the KSZ9131 has a minimal value for this time of 0.8ns which is met under all circumstances. Related-to: ELB-1299 Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2019-12-23board: colibri_imx7: reserve DDR memory for Cortex-M4Igor Opaniuk
i.MX 7's Cortex-M4 core can run from DDR and uses DDR memory for the rpmsg communication. Both use cases need a fixed location of memory reserved. For the rpmsg use case the reserved area needs to be in sync with the kernel's hardcoded vring descriptor location. Use the linux,usable-memory property to carve out 1MB of memory in case the M4 core is running. Also make sure that the i.MX 7 specific rpmsg driver does not get loaded in case we do not carve out memory. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> (cherry picked from commit c671d8af0bb07b028d808b994b83b2ec25578a44)
2019-12-18ARM: dts: imx6ull-colibri: change hierarchy of DTS filesIgor Opaniuk
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to keep original imx6ull-colibri.dts in sync with Linux. Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi + additionally fix checkpatch warnings. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> (cherry picked from commit 7d6ca12313377bad4ceafc3fa1da414d101f6b77)
2019-08-16apalis-tk1: support v1.2 hardware revisionMarcel Ziswiler
Support the V1.2 hardware revision with the following pin muxing changes: Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4 are now used as DDC pins. Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are now used as USB power enable signals. Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power enable signals are now used as GPIO3 and GPIO4. Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is loaded on V1.2 and later modules and resp. USB power enable signals activated. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com> (cherry picked from commit 4c63a601b90db131e92d3f6f6da6a4bc2b287df1)
2019-08-16apalis-tk1: remove non-essential power rails on bootDominik Sliwa
When mainline kernels reboot TK1 they use SW_RESET, that reset mode does not reset PMIC. Some rails need to be off for RAM Re-repair to work correctly. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com> (cherry picked from commit 5a20adf446bc248a8db02f6d262b43b14587812d)
2019-08-16apalis-tk1: set apalis gpio 8 aka fan_enIgor Opaniuk
Make sure the Apalis GPIO 8 aka FAN_EN is on when using Apalis TK1 modules. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com> (cherry picked from commit 538ab6c0a1a51da0caf9525607499e8cd6ef12b7)
2019-08-16apalis-tk1: do not explicitly release reset_moci#Marcel Ziswiler
By keeping RESET_MOCI_CTRL low we avoid explicitly releasing RESET_MOCI#. Please note that module hardware versions up to V1.1A will already release RESET_MOCI# in hardware coming out of reset. Please further note that with this change the USB hub on the Apalis Evaluation board is kept in reset in U-Boot and therefore none of its ports are operational in U-Boot. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com> (cherry picked from commit 5b5de78b4a6ff8c2bbd71a6b51d6fdf32f420eef)
2019-07-13toradex: configblock: avoid line continuationsMarcel Ziswiler
Fix issue as reported by checkpatch.pl. Leave long lines as line continuation in text output is not recommended. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-13toradex: configblock: fix apalis imx8 targetMarcel Ziswiler
The Apalis iMX8 was missing the interactive part should a customer have bricked his module and want to re-create the configuration block. Fix this. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-13toradex: configblock: fix colibri imx8x targetMarcel Ziswiler
The Colibri iMX8X target got re-named late in the cycle which we forgot to reflect here. Furthermore, it was missing the interactive part should a customer have bricked his module and want to re-create the configuration block. Fix this. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-13toradex: configblock: generic wi-fi/bt handlingMarcel Ziswiler
Make the interactive Wi-Fi/BT handling generic by pulling it out of the Colibri iMX6ULL interactive part to be re-used for Apalis iMX8 and Colibri iMX8X. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-13toradex: configblock: initialize MMC before switching partitionStefan Agner
If the module is in serial downloader mode, we do no longer read the environment from eMMC. Therefor, the eMMC is unitialized when trying to read the config block. Use mmc_init to initialize the selected MMC device before using it. Note: In case the MMC has already been initialized, the mmc_init detects that and returns immediately. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-09video: fsl_dcu_fb: add DM_VIDEO supportIgor Opaniuk
Extend the driver to build with DM_VIDEO enabled. DTS files must additionally include 'u-boot,dm-pre-reloc' property in soc and child nodes to enable driver binding to fsl_dcu_fb device. Currently display timings aren't obtained from DT. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-07-09video: fsl_dcu_fb: refactor init functionsIgor Opaniuk
Move dcu-related code to fsl_dcu_probe_common, keep in video_hw_init() only legacy video stack (filling GraphicPanel struct etc.). Add wrappers for all init functions, that will let to provide struct fb_info as an additional param (needed for further moving it from the global scope to driver private data struct in DM converted driver). Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-06-11board: toradex: add apalis imx8qm 4gb wb it v1.0b module supportMarcel Ziswiler
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT V1.0B module. Unlike the V1.0A early access samples exclusively booting from SD card, they are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports either booting from the on-module eMMC or may be used for recovery purpose using the universal update utility (uuu) aka mfgtools 3.0. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Gigabit Ethernet - GPIOs - I2C Unfortunately, there is no USB functionality for the i.MX 8QM as of yet. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-06-11ARM: imx: apalis_imx6: Drop ad-hoc SATA bindingMarek Vasut
Drop the ad-hoc AHCI binding code, this is superseded by CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Stefan Agner <stefan.agner@toradex.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-06-11board: toradex: add colibri imx8qxp 2gb wb it v1.0b module supportMarcel Ziswiler
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB IT V1.0B module. Unlike the V1.0A early access samples exclusively booting from SD card, they are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports either booting from the on-module eMMC or may be used for recovery purpose using the universal update utility (uuu) aka mfgtools 3.0. Functionality wise the following is known to be working: - eMMC and MMC/SD card - Ethernet - GPIOs - I2C Unfortunately, there is no USB functionality for the i.MX 8QXP as of yet. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-05-05board: toradex: drop support.arm maintainer emailMarcel Ziswiler
Drop Toradex ARM Support <support.arm@toradex.com> from maintainer email list as this just clogs our support ticketing system. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com>
2019-04-25board: toradex: tdx-cfg-block: add new skusMarcel Ziswiler
Add all the latest new SKUs: - Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT - Apalis iMX8 QuadMax 4GB IT - Apalis iMX8 QuadPlus 2GB Wi-Fi / BT - Apalis iMX8 QuadPlus 2GB", - Colibri iMX8 QuadXPlus 2GB IT - Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth - Colibri iMX8 DualX 1GB Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25board: toradex: tdx-cfg-block: clean-up sku handlingMarcel Ziswiler
Clean-up handling of several SKUs. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: migrate usb to using driver modelMarcel Ziswiler
Migrate USB to using driver model. Add USBH_PEN GPIO regulator. While at it also add alias e.g. as required for UMS. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: migrate mmc to using driver modelMarcel Ziswiler
Migrate MMC to using driver model. Migrate USDHC to using pinctrl. While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: migrate pinctrl and regulators to dtb/dmMarcel Ziswiler
Migrate pinctrl and regulators to device tree resp. driver model: Ethernet, NAND and UART. Drop BOARD_EARLY_INIT_F as it is anyway no longer used. Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25board: imx6ull: Add disable PMIC_STBY_REQPhilippe Schenker
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the SOC to request for a lower voltage during sleep. This is necessary because the voltage is changing too slow for the SOC to wake up properly. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: fix ethernet phy power onMarcel Ziswiler
Just give the new Ethernet PHY power save mode circuitry time to settle. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: set module variant depending on config blockStefan Agner
Using CPU temperature grading as a discriminator if the Wi-Fi / Bluetooth chip is populated is no longer possible due to upcoming SKUs. Set variant to -wifi only if a valid config block is present and the product id mentions a SKU with Wi-Fi / Bluetooth. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25tdx-cfg-block: simplify i.MX 6 module detectionStefan Agner
Use CONFIG_TARGET_... at compile time to differentiate between Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code duplication by moving question about Wi-Fi / Bluetooth before IT/non-IT decision. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25tdx-cfg-block: add support for new colibri iMX6ull skusGerard Salvatella
Add support for new Colibri iMX6ULL SKUs. While at it also checkpatch fix the whole files. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri_vf: fix tab vs. spacesMarcel Ziswiler
Fix indentation using tab vs. spaces. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13tdx-cfg-block: fix off by one issueMarcel Ziswiler
Fix toradex_modules array off by one issue potentially leading to spurious printout during boot e.g. Model: Toradex V1.2A, instead of Model: Toradex UNKNOWN MODULE V1.2A. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13toradex: common: unify behaviour when config block is missingBhuvanchandra DV
If the config block is missing, various things may fail or behave strangely on certain modules. This patch unifies that behaviour by using a fake MAC address, until user updates the config block. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13toradex: configblock: add an -y parameter to 'cfgblock create’Dominik Sliwa
Add an optional -y parameter to 'cfgblock create’ to simplify automation. Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: use leveling evaluated by DDR validation toolsStefan Agner
The DDR validation tool (which is part of Processor Expert) allows to evaluate leveling parameters for CR105/CR106/CR110. Several runs have been made with Colibri VF50 and VF61 and it seems to evaluate very similar values. Use this values by default. Note: The newly evaluated parameters seem to require CTLUPD_AREF to be enabled! Note 2: The tool also evaluated 6 as a new value for PHY02/18 GATE_CFG (Coarse adjust of gate open time). However, this seems not to work in practise. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_vf: adjust timing according to data sheetStefan Agner
Using the DDR Validation tool in Processor Expert uncovered two timing inconsistencies. Since those timings are related to the suspend mode they do not affect or change regular memory behaviour. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: sync the board info messageBhuvanchandra DV
Use similar info message as on other modules. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: migrate fec, esdhc, nfc and usb to driver modelMarcel Ziswiler
Migrate FEC, ESDHC, NFC and USB to driver model. While at it also do no longer enable optional I2C clock in board file as the generic clock code now handles this. Note for space reason and as it is not required just for booting we do not enable I2C in U-Boot by default. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: migrate pinctrl and regulators to dtb/dmMarcel Ziswiler
Migrate pinctrl and regulators to device tree resp. driver model: DDR, DSPI, ENET, ESDHC, I2C, NFC and UART. Enable CMD_DM, PINCTRL and DM_REGULATOR. While at it also update copyright period and sort include files. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13ARM: dts: colibri_vf: update device treesMarcel Ziswiler
Update device tree in preparation of further driver model migration: Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller, USBH_PEN GPIO regulator. Add iomux resp. pinctrl entries to be removed from proprietary platform data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO. Introduce a U-Boot specific device tree with some required u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl. pinctrl. While at it also update the MAINTAINERS file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13board: colibri_imx6: check for and report ecc errors in fusesGerard Salvatella
The PMIC on the Colibri iMX6 may have ECC errors in fuses that will prevent correct settings. Up to one bit error per fuse bank can be reported and corrected by the ECC logic. Two bit errors can only be reported. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: added nreset gpio on rebootGerard Salvatella
RGMII_RD1 pin (active high, GPIO6_IO27) is triggered on reboot during the SPL phase. This asserts (active low) nReset_Out from the PMIC. Only V1.1 and later Colibri iMX6 modules implement this in hw. Previous versions do not use this pin, so it is safe to leave it enabled at all times. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: use SDP if USB serial downloader has been usedStefan Agner
In case USB serial downloader has been used to load U-Boot start the serial download protocol (SDP) emulation. This allows to download complete images such as Toradex Easy Installer over USB SDP as well. This code uses the boot ROM provided boot information to reliably detect USB serial downloader. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13toradex: colibri_imx6: overwrite CMA memory set in device treeBhuvanchandra DV
Make sure CMA memory is not greater than 50% of available physical memory. Allow user to change the CMA memory via 'cma-size' U-Boot environment variable. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: revert fuse value set in mfgr_fuseMax Krummenacher
We have two commands to change the bootmode fuses: mfgr_fuse which set fuse 0/5 and 0/6 and updt_fuse which burns bit 4 of 0/5. Before Image 2.6 we fused in mfgr_fuse 0x5062, which boots from the user partition of the eMMC. To workaround certain hangs we moved to fastboot mode and using the first bootpartition of the eMMC requiring a fuse value of 0x5072 which could be achived by the then added updt_fuse command. At the same time the mfgr_fuse command was changed to also fuse 0x5072, revert that second change so that one can fuse both values, one with just mfgr_fuse and the later with mfgr_fuse;updt_fuse. Note that the mfgr_fuse command is only needed at module production time, a customer might need to use updt_fuse when upgrading an older module to be compatible with a newer image. The command is integrated into the image update scripts. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: change pmic fusing according to hw 1.1 requirementsMax Krummenacher
Colibri iMX6 V1.1 HW can use the PMIC GEN3 to power the NVCC_SD1. Change the settings fused into the PMIC's OTP to powerup with GEN3 set to output 3.3V. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri imx6: disable ri and dcd irq in uartsMax Krummenacher
If the UART is used in DTE mode the RI and DCD bits in UCR3 become irq enable bits. Both are set to enabled after reset and both likely are pending. Disable the bits also on UARTs not used in the boot loader to prevent an interrupt storm when Linux enables the UART interrupts. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri imx6: pf0100: reorder and cleanup message printingMax Krummenacher
Keep debug code at the end of the function. Use a one line informational message for the PMIC only. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: unify sd/mmc drive strenght with linux kernel settingsMax Krummenacher
In the linux device tree we use 40Ohm drive strenght. So use the same value in U-Boot. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: print also 64-bit ITMax Krummenacher
Print also for Colibri iMX6 512MB IT with 64-bit RAM bus. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: drop CONFIG_OF_SYSTEM_SETUPMax Krummenacher
This doesn't do anything anymore, probably never did. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_imx6: migrate usb to using driver modelMarcel Ziswiler
Migrate USB to using driver model. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-27 06:27:22 +0000