u-boot-toradex.git - U-Boot bootloader for Apalis and Colibri modules

Age	Commit message (Collapse)	Author
2018-06-06	colibri-imx6: added nreset gpio on reboot	Gerard Salvatella
	RGMII_RD1 pin (active high, GPIO6_IO27) is triggered on reboot during the SPL phase. This asserts (active low) nReset_Out from the PMIC. Only V1.1 and later Colibri iMX6 modules implement this in hw. Previous versions do not use this pin, so it is safe to leave it enabled at all times. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-08-31	colibri_imx6: use SDP if USB serial downloader has been used	Stefan Agner
	In case USB serial downloader has been used to load U-Boot start the serial download protocol (SDP) emulation. This allows to download complete images such as Toradex Easy Installer over USB SDP as well. This code uses the boot ROM provided boot information to reliably detect USB serial downloader. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-06-18	toradex: colibri_imx6: overwrite CMA memory set in device tree	Bhuvanchandra DV
	Make sure CMA memory is not greater than 50% of available physical memory. Allow user to change the CMA memory via 'cma-size' U-Boot environment variable. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-04-04	apalis/colibri imx6: disable ri and dcd irq in uarts	Max Krummenacher
	If the UART is used in DTE mode the RI and DCD bits in UCR3 become irq enable bits. Both are set to enabled after reset and both likely are pending. Disable the bits also on UARTs not used in the boot loader to prevent an interrupt storm when Linux enables the UART interrupts. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-03-30	common: apalis/colibri imx6: spl: add config to silence console output	Max Krummenacher
	This adds a Kconfig SPL_SILENCE_CONSOLE which allows to suppress any console output which in the normal program flow is printed in the SPL. Error messages and the likes will still be printed. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-01-18	apalis/colibri_imx6: use independent USB PID for SPL	Stefan Agner
	Use a completely independent USB Product ID for SPL. This allows to differentiate a SDP running in SPL and SDP running in a U-Boot which could not read the config block successfully. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2017-01-11	colibri_imx6.c: remove sata references	Max Krummenacher
	SATA is not accessible on the Colibri iMX6, so remove include and conditionally executed code. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-01-11	colibri_imx6: unify sd/mmc drive strenght with linux kernel settings	Max Krummenacher
	In the linux device tree we use 40Ohm drive strenght. So use the same value in U-Boot. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-01-11	arm: imx: initial support for colibri imx6	Max Krummenacher
	This adds board support for the Toradex module family Colibri iMX6. The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both with a version for commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> (cherry picked from commit a02d517b0182f83771565eba1329fb323674ec58)