summaryrefslogtreecommitdiff
path: root/board/amcc
AgeCommit message (Collapse)Author
2007-08-16ppc4xx: Update Sequoia/Rainier bootstrap commandStefan Roese
As suggested by David Mitchell, here an update for the Sequoia/Rainier bootstrap command. Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-14Merge with /home/stefan/git/u-boot/zeusStefan Roese
2007-08-14ppc4xx: Add initial Zeus (PPC405EP) board supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-31ppc4xx: Update AMCC Bamboo 440EP supportEugene OBrien
Changed storage type of cfg_simulate_spd_eeprom to const Changed storage type of gpio_tab to stack storage (Cannot access global data declarations in .bss until afer code relocation) Improved SDRAM tests to catch problems where data is not uniquely addressable (e.g. incorrectly programmed SDRAM row or columns) Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules Fixed AM29LV320DT (OpCode Flash) sector map Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-26ppc4xx: Add support for AMCC 405EP Taihu boardJohn Otken
Signed-off-by: John Otken <john@softadvances.com>
2007-07-16ppc4xx: AMCC Luan uses the new boardspecific DDR2 controller setupStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-16ppc4xx: Support for Yucca board with 440SPe Rev A added to 44x_spd_ddr2.cStefan Roese
The new boardspecific DDR2 controller configuration is used for the Yucca board. Now the Yucca board with 440SPe Rev. A chips is also supported. Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-04resubmit: ppc4xx: Remove sequoia/sequioa.h. Cleanup ppc440.h for PPC440EPXNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>
2007-06-25Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-06-25ppc4xx: Add pci_pre_init() for 405 boardsStefan Roese
This patch removes the CFG_PCI_PRE_INIT option completely, since it's not needed anymore with the patch from Matthias Fuchs with the "weak" pci_pre_init() implementation. Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-22Coding stylke cleanup; rebuild CHANGELOGWolfgang Denk
2007-06-22Extend POST support for PPC440Igor Lisitsin
Added memory, CPU, UART, I2C and SPR POST tests for PPC440. Signed-off-by: Igor Lisitsin <igor@emcraft.com> --
2007-06-19ppc4xx: Add bootstrap command for AMCC Sequoia (440EPx) eval boardStefan Roese
This patch adds a board command to configure the I2C bootstrap EEPROM values. Right now 533 and 667MHz are supported for booting either via NOR or NAND FLASH. Here the usage: => bootstrap 533 nor ;to configure the board for 533MHz NOR booting => bootstrap 667 nand ;to configure the board for 667MHz NNAND booting Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19[ppc4xx] Fix problem with NAND booting on AMCC AcadiaStefan Roese
The latest changes showed a problem with the location of the NAND-SPL image in the OCM and the init-data area (incl. cache). This patch fixes this problem. Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19[ppc4xx] Change board/amcc/acadia/cpr.c to pll.cStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-06ppc4xx: Add NAND booting support for AMCC Acadia (405EZ) eval boardStefan Roese
This patch adds NAND booting support for the AMCC Acadia eval board. Please make sure to configure jumper J7 to position 2-3 when booting from NOR, and to position 1-2 when booting for NAND. I also added a board command to configure the I2C bootstrap EEPROM values. Right now only 267MHz is support for booting either via NOR or NAND FLASH. Here the usage: => bootstrap 267 nor ;to configure the board for 267MHz NOR booting => bootstrap 267 nand ;to configure the board for 267MHz NNAND booting Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01ppc4xx: Add missing file for Bamboo NAND booting supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01Merge with /home/stefan/git/u-boot/bamboo-nandStefan Roese
2007-06-01ppc4xx: Undo Sequoia patch for dynamic EBC speed support of 83MHzStefan Roese
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As suggested by AMCC it is not recommended to dynamically change the EBC speed after bootup. So we undo this change to be on the safe side. Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01ppc4xx: Update Sequoia NAND booting support with ECCStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01ppc4xx: Prepare Bamboo port for NAND booting supportStefan Roese
This patch updates the "normal" Bamboo NOR booting port, so that it is compatible with the coming soon NAND booting Bamboo port. It also enables the 2nd NAND flash on the Bamboo. Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-24ppc4xx: Update AMCC Acadia support for board revision 1.1Stefan Roese
This patch updates the Acadia (405EZ) support for the new 1.1 board revision. It also adds support for NAND FLASH via the 4xx NDFC. Please note that the jumper J7 must be in position 2-3 for this NAND support. Position 1-2 is for NAND booting only. NAND booting support will follow later. Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-16[PATCH] Run new sequoia boards with an EBC speed of 83MHzJeffrey Mann
Because the Sequoia board does not boot with an EBC faster than 66MHz, the clock divider are changed after the initial boot process. This allows for maximum clocking speeds to be achieved on newer boards. Sequoia boards with 666.66 MHz processors require that the EBC divider be set to 3 in order to start the initial boot process at a slower EBC speed. After the initial boot process, the divider can be set back to 2, which will cause the boards to run at 83.333MHz. This is backward compatible with boards with 533.33 MHz processors, as these boards will already be set with an EBC divider of 2. Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
2007-05-05ppc4xx: Sequoia: Remove cpu/ppc4xx/speed.c from NAND bootingStefan Roese
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big for the 4k NAND boot image so define bus_frequency to 133MHz here which is save for the refresh counter setup. Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-29ppc4xx: Bamboo: Use current NAND driver and *not* the legacy driverStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-18ppc4xx: Update Acadia to not setup PLL when booting via bootstrap EEPROMStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-02ppc4xx: Change SysACE address on KatmaiStefan Roese
With this new base address of the Xilinx SystemACE controller the Linux driver will be easier to adapt, since it can now be mapped via the "normal" ioremap() call. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-31Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-03-31ppc4xx: Update Katmai bootstrap commandStefan Roese
Now the DDR2 frequency is also 2*PLB frequency when 166MHz PLB is selected. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-31ppc4xx: Fix "bootstrap" command for Katmai boardStefan Roese
The board specific "bootstrap" command is now fixed and can be used for the AMCC Katmai board to configure different CPU/PLB/OPB frequencies. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24Merge with /home/stefan/git/u-boot/acadiaStefan Roese
2007-03-24[PATCH] Add 4xx GPIO functionsStefan Roese
This patch adds some 4xx GPIO functions. It also moves some of the common code and defines into a common 4xx GPIO header file. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24[PATCH] Small Sequoia cleanupStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24[PATCH] Clean up 40EZ/Acadia supportStefan Roese
This patch cleans up all the open issue of the preliminary Acadia support. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-21Code cleanup. Update CHANGELOGWolfgang Denk
2007-03-21Merge with /home/stefan/git/u-boot/acadiaStefan Roese
2007-03-21[PATCH] Add AMCC Acadia (405EZ) eval board supportStefan Roese
This patch adds support for the new AMCC Acadia eval board. Please note that this Acadia/405EZ support is still in a beta stage. Still lot's of cleanup needed but we need a preliminary release now. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-16[PATCH] Use dynamic SDRAM TLB setup on AMCC Ebony eval boardStefan Roese
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the DDR memory are dynamically programmed matching the total size of the equipped memory (DIMM modules). Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08ppc4xx: Fix file mode of sequoia.cStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08ppc4xx: Clear Sequoia/Rainier security engine reset bitsJohn Otken john@softadvances.com
Signed-off-by: John Otken john@softadvances.com <john@softadvances.com>
2007-03-08Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-03-08Merge with /home/stefan/git/u-boot/yucca-ddr2Stefan Roese
2007-03-08[PATCH] Update AMCC Luan 440SP eval board supportStefan Roese
The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR inititializition. This includes DDR auto calibration and support for different DIMM modules, instead of the fixed setup used in the earlier version. This patch also enables the cache in FLASH for the startup phase of U-Boot (while running from FLASH). After relocating to SDRAM the cache is disabled again. This will speed up the boot process, especially the SDRAM setup, since there are some loops for memory testing (auto calibration). Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08[PATCH] Update AMCC Yucca 440SPe eval board supportStefan Roese
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR inititializition. This includes DDR auto calibration and support for different DIMM modules, instead of the fixed setup used in the earlier version. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08ppc4xx: Small AMCC Katmai 440SPe updateStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-07Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-03-07[PATCH] Use dynamic SDRAM TLB setup on AMCC Ocotea eval boardStefan Roese
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the DDR memory are dynamically programmed matching the total size of the equipped memory (DIMM modules). Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-06[PATCH] Speed optimization of AMCC Sequoia/Rainier DDR2 setupStefan Roese
As provided by the AMCC applications team, this patch optimizes the DDR2 setup for 166MHz bus speed. The values provided are also save to use on a "normal" 133MHz PLB bus system. Only the refresh counter setup has to be adjusted as done in this patch. For this the NAND booting version had to include the "speed.c" file from the cpu/ppc4xx directory. With this addition the NAND SPL image will just fit into the 4kbytes of program space. gcc version 4.x as provided with ELDK 4.x is needed to generate this optimized code. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-01[PATCH] Update AMCC Katmai 440SPe eval board supportStefan Roese
This patch updates the recently added Katmai board support. The biggest change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2 driver. Please note, that still some problems are left with some memory configurations. See the driver for more details. Signed-off-by: Stefan Roese <sr@denx.de>
2007-02-20[PATCH] Clean up Katmai (440SPe) linker scriptStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-05 11:58:22 +0000