summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2018-04-09arm64: zynqmp: Use maxim prefix for all maxim chipsMichal Simek
Use vendor prefix for Maxim chips. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Sync alignment with mainlineMichal Simek
Sync pcie and lpd_dma nodes with mainline version. Incorrect locations are causing diff in statistics that's why synchronizations are needed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09ARM: dts: zynq: Rename dts for Z-turn boardAnton Gerasimov
Makes naming in line with other Zynq boards. Signed-off-by: Anton Gerasimov <tossel@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09ARM: dts: zynq: Update dts for Z-turn boardAnton Gerasimov
Delete devices implemented in PL, stylistic changes. Signed-off-by: Anton Gerasimov <tossel@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-06ARM: dts: Add new "generic" am4372 device tree file.Vignesh R
With U-boot runtime board detect for DTB selection a "default" dtb needs to be created. This will be used temporarily until the "proper" dtb is selected. Also, add -u-boot.dtsi for AM437x SK and IDK to enable I2C for board detection via DM_I2C. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-04-06stm32mp: handle SYSRESETPatrick Delaunay
Add support of sysreset with generic driver "syscon-reboot" provided by RCC, for U-boot and for SPL. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06stm32mp: add syscon for STGENPatrick Delaunay
Add STGEN as SYSCON device: allow access to device address defined in device tree Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06stm32mp1: change STGEN clock source to HSEPatrick Delaunay
No more use static frequency HSI = 64MHz for STGEN clock but HSE (with higher accurency) by default. Need to remove CONFIG_SYS_HZ_CLOCK as arch timer frequency is provided at boot by BootRom and cp15 cntfrq and modified during clock tree initialization if needed. When HSI is no more used by any device, this internal oscillator can be switched off to reduce consumption. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06stm32mp1: add eMMC support for ED1Patrick Delaunay
Add command GPT support Add EMMC boot support Add the 2 other SDMMC instances for ED1: - SDMMC2 = mmc 1, eMMC on the ED1 board - SDMMC3 = extension connector, deactivated by default Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06at91: ma5d4evk: Add FDT supportJagan Teki
Sync DTS from Linux and add FDT support for AT91 ma5d4evk board. usb0, usb1, usb2 and hlcdc_pwm nodes removed, since there is no support it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-04-06at91: vinco: Add FDT supportJagan Teki
Sync DTS from Linux and add FDT support for AT91 vinco board. usb0, usb1, and usb2 nodes removed, since there is no support it. Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-04-04Merge git://git.denx.de/u-boot-sunxiTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-04arm: dts: sunxi: update H5 to new EMAC bindingAndre Przywara
The U-Boot driver for the sun8i-emac was using some preliminary DT binding. Now since Linux got its own driver in v4.15 and our driver can now cope with both bindings, let's convert the DT nodes used by the OrangePi PC2 over to the new bindings used by the kernel. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04arm: dts: sunxi: update H3 to new EMAC bindingAndre Przywara
The U-Boot driver for the sun8i-emac was using some preliminary DT binding. Now since Linux got its own driver in v4.15 and our driver can now cope with both bindings, let's convert the DT nodes used by the various H3 boards over to the new bindings used by the kernel. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04arm: dts: sunxi: update A64 to new EMAC bindingAndre Przywara
The U-Boot driver for the sun8i-emac was using some preliminary DT binding. Now since Linux got its own driver in v4.15 and our driver can now cope with both bindings, let's convert the DT nodes used for the Pine64+ board over to the new bindings used by the kernel. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-03sunxi: dts: enable NAND on NES classicMiquel Raynal
Let the Nintendo NES Classic use the Macronix NAND chip on it. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-30arm64: a37xx: dts: enable pcie portWilson Ding
This patch enabled PCIe port on both devel-board and espressobin board. Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Wilson Ding <dingwei@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30Revert "arm64: a37xx: dts: Add pin control nodes to DT"Ken Ma
The commit "arm64: mvebu: Add pinctrl nodes for Armada 3700" has added new pinctrl nodes. This reverts commit f7cab0f95b05ec6a66fe4796b9ad44406d0cc864. Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30arm64: a37xx: dts: Correct mpp definitionsKen Ma
This patch corrects below mpp definitions for armada 3720 DB board and ESPRESSOBin board: - "smi" pins group is added and "smi" function is set for eth0; - Now pcie pins are used as gpio to implement PCIe function in hardware, so "pcie" group function is changed to "gpio". Reviewed-on: http://vgitil04.il.marvell.com:8080/43287 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30arm64: a37xx: dts: Fix the number of GPIO on south bridgeKen Ma
The number of pins in South Bridge is 30 and not 29. There is a fix for the driver for the pinctrl, but a fix is also need at device tree level for the GPIO. Reviewed-on: http://vgitil04.il.marvell.com:8080/43286 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30arm64: a37xx: dts: Add additional pinctrl definitionKen Ma
Add mmc pins, pcie pins and sdio pins definition and do these pins' configuration for DB board and espressobin board; Add uart2 pins configuration for DB board. Reviewed-on: http://vgitil04.il.marvell.com:8080/40914 Reviewed-by: Wilson Ding <dingwei@marvell.com> Tested-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30arm64: a37xx: dts: Add pinctrl configuration for ESPRESSOBin boardKen Ma
Reviewed-on: http://vgitil04.il.marvell.com:8080/40913 Reviewed-by: Wilson Ding <dingwei@marvell.com> Tested-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30arm64: a37xx: dts: add gpio head file includingKen Ma
Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-23arm64: zynqmp: Remove ep108 boardMichal Simek
ZynqMP Emulation board is no longer tested and there is no reason to keep maintaining it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23arm: zynq: Enable cadence driver on zc706Michal Simek
Enable watchdog with reset-on-timeout feature. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23arm64: zynqmp: Convert board to use zynqmp-clk driverMichal Simek
Use zynqmp clock driver instead of fixed clocks. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-22ARM: dts: da850-lcdk: Sync from Linux 4.16Lokesh Vutla
Sync dts from Linux 4.16 and also add u-boot specific dtsi for OMAPl138 board. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-03-20Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-03-20armv8: ls1088aqds: Add IFC-NOR as boot source for LS1088Ashish Kumar
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT. Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and IFC-NOR to be used as flash. This allows writing to IFC-NOR flash. QSPI and DSPI cannot be accessed in this defconfig. IFC-NOR image is generated using ls1088aqds_defconfig. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-19dts: add device tree for STM32MP157C-ED1 boardPatrick Delaunay
Add minimal devicetree for STM32MP157C-ED1 board, with only the devices to allow boot from SDCARD: - RCC for clock and reset - UART4 for console - I2C and PMIC - DDR - SDMMC0 for SDCard Waiting Kernel upstream for alignment. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19arm: dts: stm32: add display for STM32F746 disco boardyannick fertre
Enable the display controller, panel & backlight. Set panel display timings & set the RGB data bus. Signed-off-by: yannick fertre <yannick.fertre@st.com>
2018-03-19arm: dts: stm32: add ltdc for STM32F746Philippe CORNU
Add display controller node in device-tree. Signed-off-by: yannick fertre <yannick.fertre@st.com> [agust: rebased on master] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2018-03-15ARM: dts: uniphier: sync with Linux 4.16-rc5Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-14Merge git://git.denx.de/u-boot-sunxiTom Rini
2018-03-13ARM: dts: dra7x: Make pinctrl and IOdelays for MMC2 available in SPLJean-Jacques Hiblot
The SPL can't use high speed MMC modes if the associated pinctrl and IOdelays are described in the DTS. Make them available in SPL by tagging the nodes with 'u-boot,dm-spl;' Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-03-13ARM: dts: dra76-evm: shift to using common IOdelay dataJean-Jacques Hiblot
Now that we have a device-tree include file with common MMC/SD IOdelay data for DRA76x SoC, shift the EVM device-tree file to using that. Also fix the name of the IO voltage regulator for mmc1. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-03-13ARM: dts: dra76x: create a common file with MMC/SD IOdelay dataJean-Jacques Hiblot
Add a common device-tree include file with MMC/SD IOdelay data for DRA76x SoC based on the linux DTSI file. In the most common case, IOdelay data available in datamanual can directly be used. This file caters to that common case. Data is based on DRA76x datamanual, SPRS993A, revised July 2017. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-03-13ARM: dts: Add support for stm32f746-evaluation board supportPatrice Chotard
This board offers: _ STM32F746NGH6 microcontroller with 1 Mbyte Flash and 320+4 Kbytes RAM _ Six 5 V power supply options: Power jack ST-LINK/V2-1 USB connector User USB HS connector User USB FS1 connector User USB FS2 connector Daughterboard _ SAI Audio DAC, stereo audio jack which supports headset with microphone _ Stereo digital microphone, audio jack connector used to connect external speakers _ 2 Gbytes (or more) SDMMC interface microSD card _ RF-EEPROM on I2C compatible serial interface _ RS-232 communication _ IrDA transceiver _ JTAG/SWD and ETM trace debug support, ST-LINK/V2-1 embedded _ IEEE-802.3-2002 compliant Ethernet connector _ Camera module _ 8Mx32 bit SDRAM, 1Mx16 bit SRAM & 8Mx16 bit Nor Flash _ 512 Mbits QuadSPI Nor Flash _ 5.7 inch 640x480 pixel TFT color LCD with capacitive touch panel _ Joystick with 4-direction control and selector _ Reset, WakeUp/Tamper or key button _ 4 color user LEDs _ Extension connectors & memory connectors for daughterboard or wrapping board _ USB OTG HS and FS with Micro-AB connectors _ RTC with backup battery _ CAN 2.0A/B compliant connection _ Potentiometer _ Motor control connector More detailed information are available here : http://www.st.com/en/evaluation-tools/stm32746g-eval.html To compile stm32f746-eval board, use same defconfig as stm32f746-disco, the only difference is to pass "DEVICE_TREE=stm32746g-eval". Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Vikas Manocha <vikas.manocha@st.com>
2018-03-13ARM: dts: stm32: limit sdio frequency to 14Mhz for stm32f429i-evalPatrice Chotard
This avoids the following errors while reading on mmc: Read data bytes CRC error: 0x2 switch to partitions #0, OK mmc0 is current device Read data bytes CRC error: 0x82002 ** Unrecognized filesystem type ** Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-03-13ARM: dts: stm32: Add timer support for STM32F7Patrice Chotard
Add missing timer node to enable timer5 for STM32F7 SoCs family Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-03-13rk3288: vyasa: Add eMMC boot supportJagan Teki
RK3288 Vyasa has eMMC boot support, with JP4 open. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13ARM: dts: rockchip: Add usb otg for rk3288-vyasaJagan Teki
Add usb otg support for rk3288-vyasa, board support usb1 otg power through otg_vbus_drv and naming conversion followed as per schematic. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13ARM: dts: rockchip: Add usb host for rk3288-vyasaJagan Teki
Add usb host support for rk3288-vyasa, board support hub power through phy_pwr_en and usb2 host power through usb2_pwr_en and naming conversion followed as per schematic. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13ARM: dts: rockchip: Add gmac support for rk3288-vyasa boardJagan Teki
Sync gmac dts node from Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13ARM: dts: rockchip: Add regulators for rk3288-vyasaJagan Teki
Add supporting regulators for rk3288-vyasa board, dc12_vbat is parent regulatorand followed regulators as are child regulators. regulator naming conversion followed as per schematic for better readability and easy for identification. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13ARM: dts: rockchip: rk3288-vyasa: Use vmmc-supply from PMICJagan Teki
rk808, SWITCH_REG1 has configured for sdmmc regulator as vcc_sd, so use the same by renaming vcc33_sd to vcc_sd(as per schematic) and drop explicit regulator definition from root. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13ARM: dts: rockchip: rk3288-vyasa: Remove vdd_log from rk808, DCDC_REG1Jagan Teki
vdd_log, never used on DCDC_REG1 of rk808 from latest schematic so remove the same and update the regulator-name as 'vdd_arm' to sync with existing rk3288 board dts files. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13ARM: dts: rockchip: Sync rk3288-vyasa dts from LinuxJagan Teki
Sync rk3288-vyasa board dts from Linux for proper updates and maintenance - rk3288-vyasa.dts: Similar to Linux dts - rk3288-vyasa-u-boot.dtsi: u-boot dts changes Also updated MAINTAINERS for these dts files. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13sunxi: Add A20-SOM204-EVB-eMMC boardStefan Mavrodiev
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired to MMC2 slot. This patch adds defconfig and dts files for this board. The dts is same with mainline kernel. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13sunxi: Add A20-SOM204-EVB boardStefan Mavrodiev
This is new System-On-Module platform with universal dimm socket for easy insertation. The EVB board is designed to be universal with future modules. Base features of A20-SOM204 board includes: * 1GB DDR3 RAM * AXP209 PMU * KSZ9031 Gigabit PHY * AT24C16 EEPROM * Status LED * LCD connector * GPIO connector There will be variants with the following options: * Second LAN8710A Megabit PHY * 16MB SPI Flash memory * eMMC card * ATECC508 crypto device The EVB board has: * Debug UART * MicroSD card connector * USB-OTG connector * Two USB host * RTL8723BS WiFi/BT combo * IrDA transceiver/receiver * HDMI connector * VGA connector * Megabit ethernet transceiver * Gigabit ethernet transceiver * SATA connector * CAN driver * CSI camera * MIC and HP connectors * PCIe x4 connector * USB3 connector * Two UEXT connectors * Two user LEDs Some of the features are multiplexed and cannot be used the same time: CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3. This patch adds defconfig and dts files for this board. The dts is same with mainline kernel, except some nodes are removed to make file compatible with existing dtsi file. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-10 07:15:59 +0000