summaryrefslogtreecommitdiff
path: root/arch/arm/dts/tegra20-seaboard.dts
AgeCommit message (Collapse)Author
2016-09-27ARM: tegra: fix ULPI PHY on Ventana and SeaboardStephen Warren
Commit ce02a71c2374 "tegra: dts: Sync tegra20 device tree files with Linux" enabled the ULPI USB port on Ventana, but made no attempt to ensure that U-Boot code could handle this. In practice, various code is missing, and various configuration options are not enabled, which causes U-Boot to hang when attempting to initialize this USB port. This patch enables ULPI PHY support on Ventana, and adds the required pinmux setup for the port to operate. Note that Ventana is so similar to Seaboard that this change is made in the Seaboard board file, which is shared with Ventana. Seaboard also has the ULPI USB port wired up in hardware, although to an internal port that often doesn't have anything attached to it. However, the DT nodes for the USB controller and PHY had different status property values, so the port was not initialized by U-Boot. Fix this inconsistency, and enable the ULPI port, just like in the Linux kernel DT. This likewise requires enabling ULPI support in the Seaboard defconfig. Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27ARM: tegra: fix USB controller aliasesStephen Warren
Some boards have a different set of USB controllers enabled in DT than the set referenced by /alias entries. This patch fixes that. For example, this avoids the following message while booting on Ventana, which is caused by the fact that the USB0 controller had no alias, and defaulted to wanting a sequence number of 0, which was later explicitly requested by the alias for USB controller 2. USB2: Device 'usb@c5008000': seq 0 is in use by 'usb@c5000000' This didn't affect USB operation in any way though. Related, there's no need for the USB controller aliases to have an order that's different from the HW order, so re-order any aliases to match the HW ordering. This has the benefit that since USB controller 0 is the only one that supports device-mode in HW, and U-Boot only supports enabling device move on controller 0, there's now good synergy in the ordering! For Tegra20, that's not relevant at present since USB device mode doesn't work correctly on that SoC, but it will save some head-scratching later. This patch doesn't fix the colibri_t20 board, even though it has the same issue, since Marcel already sent a patch for that. Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-on: Harmony and Ventana
2016-09-27mmc: tegra: use correct alias for SDHCI/MMC nodesStephen Warren
The Tegra MMC driver currently honors "sdhci" entries in /aliases. The MMC core however uses "mmc" entries in /aliases. This difference will be relevant once the Tegra MMC driver is converted to DM, and the MMC core handles alias lookups. To avoid issues during that conversion, fix the Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC core does. Cc: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05video: tegra: Move to using simple-panel and pwm-backlightSimon Glass
We have standard drivers for panels and backlights which can do most of the work for us. Move the tegra20 LCD driver over to use those instead of custom code. This patch includes device tree changes for the nvidia boards. I have only been able to test seaboard. If this patch is applied, these boards will also need to be synced with the kernel, and updated to use display-timings: - colibri - medcom-wide - paz00 - tec Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05tegra: dts: Sync tegra20 device tree files with LinuxSimon Glass
Sync everything except the display panel, which will come in a future patch. One USB port is left disabled since we don't want to support it in U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-17video: tegra: refuse to bind to disabled dcsStephen Warren
This prevents the following boot-time message on any board where only the first DC is in use, yet the DC's DT node is enabled: stdio_add_devices: Video device failed (ret=-22) (This happens on at least Harmony, Ventana, and likely any other Tegra20 board with display enabled other than Seaboard). The Tegra DC's DT node represents a display controller. It may itself drive an integrated RGB display output, or be used by some other display controller such as HDMI. For this reason the DC node itself is not enabled/disabled in DT; the DC itself is considered a shared resource, not the final (board-specific) display output. The node should instantiate a display output driver only if the rgb subnode is enabled. Other output drivers are free to use the DC if they are enabled and their DT node references the DC's DT node. Adapt the Tegra display drivers' bind() routine to only bind to the DC's DT node if the RGB subnode is enabled. Now that the display driver does the right thing, remove the workaround for this issue from Seaboard's DT file. Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-16tegra: video: Move LCD driver to use the DM PWM driverSimon Glass
Use the driver-model PWM driver in preference to the old code. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: video: Convert tegra20 LCD driver to driver modelSimon Glass
Move this driver over to use driver model. This involves rearranging the code somewhat. The effect is that everything is run from the probe() method. Boards which use this are fixed up, but only seaboard is tested. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: dts: Sync tegra20.dtsi with Linux v4.4Simon Glass
This file has changed quite a bit since it was set up. Sync it back with Linux v4.4. Adjust the users slightly to cope with the changes: - the host1x node is now called host1x@50000000 - we need a clocks node to provide the clk32k_in phandle - active usb nodes need status = "okay" - active i2c nodes need status = "okay" Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-01-29dm: tegra: dts: Use TEGRA_GPIO() macro for all GPIOsSimon Glass
This new method is much easier and matches the kernel. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10tegra: dts: Add serial port detailsSimon Glass
Some Tegra device tree files do not include information about the serial ports. Add this and also add information about the input clock speed. The console alias needs to be set up to indicate which port is used for the console. Also add a binding file since this is missing. Series-changes; 5 - Add full serial port nodes from Linux tree (commit fc9d4dbe) - Use /chosen/stdout-path instead of /aliases/console to specify the console Signed-off-by: Simon Glass <sjg@chromium.org>
2014-02-19dts: move device tree sources to arch/$(ARCH)/dts/Masahiro Yamada
Unlike Linux Kernel, U-Boot historically had *.dts files under board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/. I think arch/$(ARCH)/dts dicretory is a better location to store both *.dts and *.dtsi files. For example, before this commit, board/xilinx/dts directory had both Microblaze dts (microblaze-generic.dts) and ARM dts (zynq-*.dts), which are totally unrelated. This commit moves *.dts to arch/$(ARCH)/dts/ directories, allowing us to describe nicely mutiple DTBs generation in the next commit. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>