summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-03-01OMAP3: drop CONFIG_SPL_OS_BOOT_KEY and use local defineStefano Babic
CONFIG_SPL_OS_BOOT_KEY is used only in board files. It is not required to have a general CONFIG_ option. Rename it and define it in board directory. Signed-off-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-01Add README for the "Falcon" modeStefano Babic
Simple howto to add support to a board for booting the kernel from SPL ("Falcon" mode). Signed-off-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Tom Rini <trini@ti.com>
2013-02-22common/env_nand.c: calculate crc only when readenv was OKPhil Sutter
Calculating the checksum of incompletely read data is useless. Signed-off-by: Phil Sutter <phil.sutter@viprinet.com> [scottwood@freescale.com: minor formatting fix] Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-02-22env_nand.c: clarify log messages when env reading failsPhil Sutter
The single message is misleading, since there is no equivalent success note when reading the other copy succeeds. Instead, warn if one of the redundant copies could not be loaded and emphasise on the error when reading both fails. Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
2013-02-22mtd: nand: Check if NAND is locked tight before lock cmdsJoe Hershberger
If the NAND is locked tight, commands such as lock and unlock will not work, but the NAND chip may not report an error. Check the lock tight status before attempting such operations so that an error status can be reported if we know the operation will not succeed. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-02-22nand: fix nand read.option parsingHarvey Chapman
"nand read.part addr off size" would be treated as "nand read.raw addr off 1" It now fails as intended stating "Unknown nand command suffix '.part'" Signed-off-by: Harvey Chapman <hchapman@3gfp.com>
2013-02-22imls: Add support to list images in NAND deviceVipin Kumar
This patch adds support to list images in NAND flash through imls Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
2013-02-20MAKEALL: add support for per architecture toolchainsAllen Martin
Add support for per architecture CROSS_COMPILE toolchain definitions via CROSS_COMPILE_ARCH where "ARCH" is any of the supported u-boot architectures. This allows building every supported u-boot board in a single pass of MAKEALL. Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
2013-02-20gpt: fix partion size limitPiotr Wilczek
Currently, in gpt command, partion size is converted from string to unsigned long type using 'ustrtol' function. That type limits the partition size to 4GB. This patch changes the conversion function to 'ustrtoll' to return unsigned long long type. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2013-02-20mac: Fix the condition check for setting the MAC from the EEPROMHolger Hans Peter Freyther
The issue got introduced in a cleanup by Manjunath Hadli in commit 826e99136e2bce61f3f6572e32d7aa724c116e6d. The eth_getenv_enetaddr_by_index method will validate the MAC addr and if none is set in the environment 0 will be returned. Set the MAC from the eeprom if no valid address is found in environment. Signed-off-by: Holger Hans Peter Freyther <holger@freyther.de>
2013-02-20led: The gpio_led.c code expects that LED state is from the enumHolger Hans Peter Freyther
u-boot is not consistent if state should be 0|1 or of the enum, the GPIO driver expects this to be one of the enum values. Update the caller. Signed-off-by: Holger Hans Peter Freyther <holger@freyther.de>
2013-02-20gpio: Build the da8xx_gpio code for the davinci644x deviceHolger Hans Peter Freyther
The differences include the number of GPIOs and that one is not required to set the pinmux on request. Signed-off-by: Holger Hans Peter Freyther <holger@freyther.de>
2013-02-20cmd_elf: Fix broken bootvx commandReinhard Arlt
Fix broken bootvx command. Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
2013-02-19cmd_load.c: Add #endif comments to reduce confusionRobert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-02-19cmd_mem.c: Fix some typoes, no functional changesRobert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-02-19fw_env.config: Correct "fw_saveenv" to "fw_setenv".Robert P. J. Day
Fix a comment in the fw_env.config file, no functional change. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-02-19vsprintf: add ustrtoll functionPiotr Wilczek
Add 'ustrtoull' function to convert size from string (ex: 1GiB) to unsigned long long type Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2013-02-19malloc: make malloc_bin_reloc staticGabor Juhos
On architectures where manual relocation is needed, the 'malloc_bin_reloc' function must be called after 'mem_malloc_init'. Make the 'malloc_bin_reloc' function static and call it directly from 'mem_malloc_init' instead of calling that from board_init_{r,f} functions of the affected architectures. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Wolfgang Denk <wd@denx.de> Cc: Andreas Bießmann <andreas.devel@gmail.com> Cc: Jason Jin <Jason.jin@freescale.com> Cc: Macpaul Lin <macpaul@andestech.com> Cc: Daniel Hellstrom <daniel@gaisler.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-02-19serial/ns16550: don't generate functions for undefined portsScott Wood
This saved 640 bytes on MPC8536DS (a board with two of the six ports defined). Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-02-18Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxTom Rini
2013-02-18nds32: Add a basic errno.hSimon Glass
This is available on other architectures, and nds32 will start to break without it as code starts to use error numbers more. Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-15powerpc/83xx/km: drop uneeded dtt_bus environment varHolger Brunck
There is no need for a environment variable to configure the dtt bus. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: remove uneeded CONFIG_MISC_INIT_RHolger Brunck
Remove it from the processor specific headers. This is already defined in the common header km83xx.h. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: add support for kmopti2 boardHolger Brunck
This board is similar to TUXX1 but it has a different sized second FPGA. Therefore the configuration for the third chipselect is different. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: cleanup tuxx1 supportHolger Brunck
This is a preparation for the upcoming kmopti2 board. This board has also a second fpga on board which is different to the tuxx1 target. But we want to use the same header file. So remove the config option KM_DISABLE_APP2 and simply use the board names to distinguish the features. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common: add eccmode to kernel commandlineHolger Brunck
If CONFIG_NAND_ECC_BCH is chosen from in the board configuration we add an ecc mode to the kernel commandline. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx: use NAND_ECC_BCH for kmcoge5neHolger Brunck
Switch from 1-bit ecc to 4-bit ecc. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15kmeter1_nand: allow uasge of NAND_ECC_SOFT_BCHHolger Brunck
If CONFIG_NAND_ECC_BCH is set we use 4-bit error corretion code instead of the 1-bit error correction code on the NAND device within this driver. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Scott Wood <scottwood@freescale.com>
2013-02-15km/scripts: replace hardcoded uImageAndreas Huber
Replace uImage with ${uimage}. If uimage is not set, default it to uImage. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common: introduce $uimage variableAndreas Huber
Replace the hardcoded string with a variable. If CONFIG_NAND_ECC_BCH is set we use a specific name for the uImage (ecc_bch_uImage). Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx: use ppc_6xx as arch variable for kmvect1Holger Brunck
On this board we are using hard floating point, so select the correct toolchain. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: add MV88E6122 switch support for kmvect1Karlheinz Jerg
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection to the switch MV88E6122. This switch has a connection to a frontport ethernet interface. The ethernet port used for network booting is automatically selected by u-boot. If a Piggy is plugged, the Piggy port is selected (UEC2, eth1). If the Piggy isn't present, the Frontport is selected (UEC0, eth0). The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28) and released at startup. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: rework piggy mac adress offset generationHolger Brunck
For the the kmvect1 board we will also need a functionality to add an offset to the IVMs MAC address, because these board will have two valid ethernet ports for debugging purpose. So move the code to an own function. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km82xx, km83xx: move ethernet_present() from common to cpu specificKarlheinz Jerg
For kmvect1 we need a special solution and for km_arm boards we already have. So move the common code to the architectur specific file. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: remove CONFIG_SYS_I2C_IVM_BUS related codeHolger Brunck
This define isn't set within our setup files. So we can safely remove the affected code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: remove obsolete codeHolger Brunck
EEprom_ivm_addr isn't set in our environment, so remove the usage of this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common: remove unneeded ifdefs for I2CHolger Brunck
All boards from this serie use i2c. There is no need to #ifdef the header. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15Merge branch 'master' of git://git.denx.de/u-bootKim Phillips
2013-02-15Merge branch 'fixes' of git://git.denx.de/u-boot-mipsTom Rini
2013-02-15MIPS: board.c: remove manual relocation of env_name_specDaniel Schwierzeck
Remove the manual relocation of env_name_spec. This has been missed in the previous patch series for introducing dynamic relocation on MIPS. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-14x86: Remove unused real mode codeSimon Glass
This code is pretty old and we want to support only 32-bit systems now. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Graeme Russ <graeme.russ@gmail.com>
2013-02-14x86: Rename CONFIG_NO_X86_RESET_VECTOR to CONFIG_X86_RESET_VECTORSimon Glass
Invert the polarity of this option to simplify the Makefile logic. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Gabe Black <gabeblack@chromium.org>
2013-02-14x86: Remove unneeded cruft from main MakefileSimon Glass
These lines are dealt with in the x86 Makefile and link script, so punt them. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Gabe Black <gabeblack@chromium.org>
2013-02-14x86: Remove sc520 cpuSimon Glass
This x86 CPU variant is no longer required as the boards that use it have been removed. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Graeme Russ <graeme.russ@gmail.com>
2013-02-14x86: Remove eNET boardsSimon Glass
These are no longer used and should be removed. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Graeme Russ <graeme.russ@gmail.com>
2013-02-12Merge branch 'next' of git://git.denx.de/u-boot-mipsTom Rini
2013-02-12MIPS: add dynamic relocation supportGabor Juhos
The code handles relocation entries with the following relocation types only: mips32: R_MIPS_REL32 mips64: R_MIPS_REL+R_MIPS_64 xburst: R_MIPS_REL32 Other relocation entries are skipped without processing. The code must be extended if other relocation types must be supported. Add -pie to LDFLAGS_FINAL to generate the .rel.dyn fixup table, which will be applied to the relocated image before transferring control to it. The CONFIG_NEEDS_MANUAL_RELOC is not needed after the patch, so remove that as well. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12MIPS: u-boot.lds: add relocation specific sectionsGabor Juhos
This section contain the table needed for dynamic relocation. Also provide symbols for the relocation code to access the table. Discard all sections which are not needed in the final ELF binary and U-Boot image. Section .dynsym cannot be discarded or GNU ld crashes otherwise. This section will be stripped by GNU objcpy in a later patch. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12MIPS: start.S: use symbol __image_copy_end for U-Boot image relocationDaniel Schwierzeck
Use the newly introduced symbol __image_copy_end as end address for relocation of U-Boot image. This is needed for dynamic relocation added in later patches. This patch obsoletes the symbols uboot_end and uboot_end_data which are removed. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12MIPS: start.S: optimize BSS initializationDaniel Schwierzeck
Get the start and end address for clearing BSS from the newly introduced symbols __bss_start and __bss_end. After GOT is relocated, those symbols are already pointing to the correct addresses. Also optimize the loop by moving the address incrementation to the delay slot to avoid the initial sub instruction. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>