summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-03-29usb: Add support for txfifo thresholdSimon Glass
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the txfilltuning field in the EHCI controller on reset. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: usb: fdt: Add USB definitions for Tegra2 SeaboardSimon Glass
We set up two USB ports, one of which can be host or device. For some reason the kernel version does enable both ports. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: usb: fdt: Add additional device tree definitions for USB portsSimon Glass
This adds clock references to the USB part of the device tree for U-Boot, and marks USB1 as supporting legacy mode (which we disable in the driver). The USB timing information may vary between boards sometimes, but for now we hard-code it in C. This is because all current T2x boards use the same values, we will deal with T3x later and we first need to agree on the format for this timing information in the fdt and may in fact decide that it has no place there. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: fdt: Add clock bindings for Tegra2 SeaboardSimon Glass
Add the definition of the oscillator clock frequency and the 32KHz clock. The latter is provided by a PMIC on I2C which we don't actually use at present, but we expect this definition to be used in the kernel and want to keep our .dts the same. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: fdt: Add clock bindingsSimon Glass
This adds a basic binding for the oscillator and peripheral clocks. The second cell is the clock number, defined as the bit number within the clock enable register if the peripheral clock. This uses the RFC clock bindings from Grant Likely so may change later: https://lkml.org/lkml/2011/12/12/498 It is taken from Stephen Warren's patch here: http://patchwork.ozlabs.org/patch/141359/ Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: fdt: Add additional USB bindingSimon Glass
This adds a property to indicate a port which can switch between host and device mode. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29fdt: Add tegra-usb bindings file from linuxSimon Glass
This file is taken from the Linux mailing list. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29fdt: Add staging area for device tree binding documentationSimon Glass
Add a directory to hold device tree binding files, to permit easy review of this material in U-Boot patches. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: fdt: Add device tree file for Tegra2 Seaboard from kernelSimon Glass
This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: fdt: Add Tegra2x device tree file from kernelSimon Glass
This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git config.mk is updated to provide this file to boards through the built-in mechanism: /include/ ARCH_CPU_DTS Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29arm: fdt: Add skeleton device tree file from kernelSimon Glass
This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29fdt: Add basic support for decoding GPIO definitionsSimon Glass
This adds some support into fdtdec for reading GPIO definitions from the fdt. We permit up to FDT_GPIO_MAX GPIOs in the system. Each GPIO is of the form: gpio-function-name = <phandle gpio_num flags>; where: phandle is a pointer to the GPIO node gpio_num is the number of the GPIO (0 to 223) flags is a flag, as follows: bit meaning 0 0=polarity normal, 1=active low (inverted) An example is: enable-propounder-gpios = <&gpio 43 0>; which means that GPIO 43 is used to enable the propounder (setting the GPIO high), or that you can detect that the propounder is enabled by checking if the GPIO is high (the fdt does not indicate input/output). Two main functions are provided: fdtdec_decode_gpio() reads a GPIO property from an fdt node and decodes it into a structure. fdtdec_setup_gpio() sets up the GPIO by calling gpio_request for you. Both functions can cope with the property being missing, which is taken to mean that that GPIO function is not available or is not needed. [For reference, from Stephen Warren <swarren@nvidia.com>. It may be that we add this extra complexity later if needed: The correct way to parse such a GPIO property in general is: * Read the first cell. * Find the node referenced by the phandle (the controller). * Ensure property gpio-controller is present in the controller node. * Read property #gpio-cells from the controller node. * Extract #gpio-cells from the original property. * Keep processing more cells from the original property; there may be multiple GPIOs listed. According to the binding documentation in the Linux kernel, Samsung Exynos4 doesn't use this format, and while all other chips do have a flags cell, about 50% of the controllers indicate the cell is unused. ] Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29fdt: Add functions to access phandles, arrays and boolsSimon Glass
Add a function to look up a property which is a phandle in a node, and another to read a fixed-length integer array from an fdt property. Also add a function to read boolean properties, although there is no actual boolean type in U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29fdt: Tidy up a few fdtdec problemsSimon Glass
This fixes five trivial issues in fdtdec.c: 1. fdtdec_get_is_enabled() doesn't really need a default value 2. The fdt must be word-aligned, since otherwise it will fail on ARM 3. The compat_names[] array is missing its first element. This is needed only because the first fdt_compat_id is defined to be invalid. 4. Added a header prototype for fdtdec_next_compatible() 5. Change fdtdec_next_alias() to only increment its 'upto' parameter on success, to make the display error messages in the caller easier. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29fdt: Add tests for fdtdecSimon Glass
The fdtdec_find_aliases_for_id() function is complicated enough that it really should have some tests. This does not necessarily need to be committed to U-Boot, but it might be useful. (note there are a few minor inconsistencies with this patch which will be cleaned up when the USB series is applied) Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29fdt: Add fdtdec_find_aliases() to deal with alias nodesSimon Glass
Stephen Warren pointed out that we should use nodes whether or not they have an alias in the /aliases section. The aliases section specifies the order so far as it can, but is not essential. Operating without alisses is useful when the enumerated order of nodes does not matter (admittedly rare in U-Boot). This is considerably more complex, and it is important to keep this complexity out of driver code. This patch creates a function fdtdec_find_aliases() which returns an ordered list of node offsets for a particular compatible ID, taking account of alias nodes. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer loadTom Warren
The 4.2.2 gcc in the ELDK42 release doesn't like the direct SP load using a constant in tegra2_start. Change it to use a load thru another reg using mov sp, %0 : : "r"(CONST). Tested on my Seaboard T20-A03, U-Boot loads and runs OK. Also compiled all tegra2 builds with both gcc 4.2.2 and 4.4.1 OK. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2012-03-29net: fec_mxc: allow use with cache enabledEric Nelson
Ensure that transmit and receive buffers are cache-line aligned. Invalidate cache for each packet as received, update receive buffer descriptors one cache line at a time, flush cache before transmitting. Original patch by Marek: http://lists.denx.de/pipermail/u-boot/2012-February/117695.html Signed-off-by: Eric Nelson <eric.nelson at boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de>
2012-03-29net: force PKTALIGN to ARCH_DMA_MINALIGNEric Nelson
This will prevent the need for architectures whose DMA alignment is greater than 32 to have bounce buffers. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-03-29i.MX28: Enable caches by defaultMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-03-29i.MX28: Make use of the bounce bufferMarek Vasut
This allows i.MX28 MMC host to fully utilize DMA transfers and caches, greatly improving speed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com>
2012-03-29i.MX28: Do data transfers via DMA in MMC driverMarek Vasut
This utilizes the newly introduced bounce buffers in the MMC layer. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Fabio Estevam <festevam@gmail.com>
2012-03-29MMC: Implement generic bounce bufferMarek Vasut
This implements generic bounce buffer at the end of MMC command submission chain. Therefore if unaligned data are passed, they are copied. This stuff should be pushed down into the MMC subsystem to squash all places generating these unaligned data. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andy Fleming <afleming@gmail.com>
2012-03-29i.MX28: Add cache support to MXS NAND driverMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-03-29i.MX28: Add cache support into the APBH DMA driverMarek Vasut
The desc_append() now flushes descriptors into RAM. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-03-29ARM926EJS: Implement cache operationsMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-03-28board/vpac270/onenand.c: Fix build errorsAnatolij Gustschin
Building for vpac270_ond_256 configuration fails: arch/arm/lib/libarm.o: In function `icache_disable': /home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:156: multiple definition of `icache_disable' board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:65: first defined here arch/arm/lib/libarm.o: In function `dcache_disable': /home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:188: multiple definition of `dcache_disable' board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:66: first defined here make[1]: *** [/home/ag/git/u-boot/spl/u-boot-spl] Error 1 Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2012-03-28nhk8815: fix build errorsAnatolij Gustschin
Fix: common/libcommon.o: In function `cread_line': /home/ag/git/u-boot/common/main.c:695: undefined reference to `get_ticks' /home/ag/git/u-boot/common/main.c:695: undefined reference to `get_tbclk' /home/ag/git/u-boot/common/main.c:698: undefined reference to `get_ticks' Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Alessandro Rubini <rubini@unipv.it> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Alessandro Rubini <rubini@unipv.it>
2012-03-28atmel-boards: add missing atmel_mci.hAndreas Bießmann
commit 72fa467988e7944407a634ddc4bc6a2df685c04c moved atmel_mci_init() into include/atmel_mci.h. Some AT91 boards are also using this interface and need to include atmel_mci.h now. This patch fixes MAKEALL complaints like this: ---8<--- Configuring for ethernut5 - Board: ethernut5, Options: AT91SAM9XE ethernut5.c: In function 'board_mmc_init': ethernut5.c:235:2: warning: implicit declaration of function 'atmel_mci_init' [-Wimplicit-function-declaration] --->8--- Signed-off-by: Andreas Bießmann <biessmann@corscience.de> CC: Albert Aribaud <albert.u.boot@aribaud.net> CC: Reinhard Meyer <u-boot@emk-elektronik.de> CC: egnite GmbH <info@egnite.de>
2012-03-28ARM: highbank: setup env from boot source registerRob Herring
Add support to read the boot src register and set bootcmd env from the selected bootcmdX env setting. Based on Linkstation boot choice selection. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28ARM: highbank: change env config to use nvramJason Hobbs
Update the highbank config to use env from NVRAM. Also remove extra env settings as they are not used unless the default env is used. Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28ARM: highbank: add reset supportRob Herring
Implement reset for highbank platform. Reset is triggered via a wfi instruction, so enabling armv7 for the compiler is necessary. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28ARM: highbank: Add boot counter supportRob Herring
Add boot counter support using an sysreg which is persistent across reset. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28ARM: highbank: change TEXT_BASE to 0x8000Rob Herring
Make some space at the beginning of RAM so the FDT can be loaded to a known fixed address at 0x1000. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28ARM: highbank: fix us_to_tick calculationRob Herring
udelay calls were off due to failing to convert us to ns. Fix this and drop the unnecessary shifts since NS_PER_TICK is only 7ns. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28ARM: highbank: add missing get_tbclkRob Herring
The get_tbclk function was missing and the recent commit "common: add possibility for readline_into_buffer timeout" makes it required. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28ARM: highbank: fix warning for calxedaxgmac_initializeRob Herring
Add include of netdev.h to pick-up declaration of calxedaxgmac_initialize. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28net: calxedaxgmac: fix build due to missing __aligned definitionRob Herring
Include linux/compiler.h to fix build error due to missing __aligned definition. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28Enable high speed support for USB device framework and usbttyVipin KUMAR
This patch adds the support for high speed in usb device framework and usbtty driver. This feature has been kept within a macro CONFIG_USBD_HS, so the board configuration files have to define this macro to enable high speed support. Along with that specific peripheral drivers also need to define a function to let the framework know that the enumeration has happened at high speed. This function prototype is "int is_usbd_high_speed(void)" Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-03-28lzma: fix printf warningsMike Frysinger
Fix size_t printf format warnings: LzmaTools.c: In function 'lzmaBuffToBuffDecompress': LzmaTools.c:110:5: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'SizeT' LzmaTools.c:111:5: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'SizeT' Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-03-27EXYNOS: Add structure for Exynos4 DMCChander Kashyap
Add exynos4_dmc structure in dmc.h for exynos4 dram controllor(DMC). Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-03-27EXYNOS: SMDK5250: Support all 4 UARTsDoug Anderson
This properly configures the mux to enable all UARTs. This also fixes things so that we don't configure balls XUCTSN_1 and XURTSN_1 as UART1 configuration (RTS/CTS), since they aren't connected. Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Chander kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-03-27ARM: fix s3c2410 timer codeDavid Müller (ELSOFT AG)
This patch fixes the s3c24x0 timer code to work with the ARM relocation feature. Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-03-27ARM: davinci: fixes for cam_enc_4xx boardHeiko Schocher
- change CONFIG_ENV_RANGE to contain 2 nand erase blocks, one for bad block reserve. - remove from the envvariable "img_writeramdisk" the ubifsmount command, as it is not needed. - erase the hole mtd partition containing u-boot - save environment variable "dvn_app_vers" and "dvn_boot_vers" only after installing the new image. changes requested from Marek Vasut: - arm, davinci: fix eldk-4.2 warnings for cam_enc_4xx board - get rid of run_command2 usage needed since patch: commit 009dde1955583e306cf904c864068f3acb0db499 Author: Simon Glass <sjg@chromium.org> Date: Tue Feb 14 19:59:20 2012 +0000 Rename run_command2() to run_command() is now in mainline. - add CONFIG_SPL_LIBGENERIC_SUPPORT support - remove CONFIG_CMD_PXE support - fix warning: cam_enc_4xx.c: In function 'menu_handle': cam_enc_4xx.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules - fix error: arm-linux-ld: u-boot-spl: Not enough room for program headers, try linking with -N Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Tom Rini <tom.rini@gmail.com> Cc: Fletzer Martin <Martin.Fletzer@ait.ac.at> Cc: Wolfgang Denk <wd@denx.de>
2012-03-27omap3_spi: receive transmit modejacopo mondi
Implementation of receive-transmit mode for omap3 MCSPI. Introduces full duplex communication, needed by some spi devices (such as enc28j60). Signed-off-by: jacopo mondi <mondi@cs.unibo.it> <j.mondi@voltaelectronics.com>
2012-03-27calimain, enbw_cmc: Fix typo in commentsChristian Riesch
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2012-03-27Davinci: ea20: use gpio framework to access gpiosStefano Babic
Drop direct access to SOC's registers and use the function of the GPIO driver for da8xx. [Tom: Remove gpio[68]_base as it's now unused] Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Bastian Ruppert <Bastian.Ruppert@Sewerin.de> CC: dzu@denx.de CC: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-03-27OMAP3: mt_ventoux: sets its own mtdpartsStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
2012-03-27OMAP3: mt_ventoux: updated timing for FPGAStefano Babic
Fix chipselect timing for FPGA Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
2012-03-27twl4030: fix potential power supply handling issuesGrazvydas Ignotas
twl4030_pmrecv_vsel_cfg currently first sets up device group (effectively enabling the supply), and only then sets vsel (selects voltage). This could lead to wrong voltage for a short time, or even long time if second i2c write fails. Fix this by writing vsel first and device group after that. Also introduce error checking to not enable the supply if we failed to set the voltage, and start logging errors as power supply problems are usually important. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-27 07:58:40 +0000