summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-02-27Kconfig: cmd: Make networking command dependent on NETMichal Simek
Enable networking command only when NET is enabled. And remove selecting NET for CMD_NET Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-25Merge git://git.denx.de/u-boot-mmcTom Rini
2018-02-26mmc: omap_hsmmc: use a default 52MHz max clock rate if none is specifiedJean-Jacques Hiblot
mmc_of_parse() doesn't set a default value if none is available in DT. In that case, use a default 52MHz clock rate. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-26mmc: omap_hsmmc: make it possible to compile out ADMA supportJean-Jacques Hiblot
Some platforms don't have ADMA controllers. For those platforms, compiling it out reduces the size of the binary by about 600 bytes. Leaving the support in doesn't break things as the driver checks at runtime if the ADMA2 controller is present. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-26mmc: omap_hsmmc: compile out write support if not neededJean-Jacques Hiblot
This reduces the size of the binary by about 196 bytes. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-26mmc: omap_hsmmc: do not embed struct mmc in struct omap_hsmmc_platJean-Jacques Hiblot
The area for struct mmc can be allocated dynamically. It greatly reduces the size of struct omap_hsmmc_plat. This is useful in cases where the board level code declares one or two struct omap_hsmmc_plat because it doesn't use the Driver Model. This saves around 740 bytes for the am335x_evm SPL. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-25Merge git://git.denx.de/u-boot-rockchipTom Rini
2018-02-25Merge git://git.denx.de/u-boot-imxTom Rini
2018-02-25bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDRTom Rini
Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can provide a default for BOOTCOUNT_AM33XX as that's a specific part of the RTC in use. We can also provide a default for ARCH_LS1043A and ARCH_LS1021A as they had been previously calculated and their symbols are in Kconfig. In the case of other QE-enabled platforms, they are not so we must update the relevant defconfig files. The previous default only applied in some cases, even on a specific SoC family. Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-24imx: spl: Partially revert "spl: eMMC/SD: Provide one __weak spl_boot_mode() ↵Fabio Estevam
function" Commit d695d6627803 ("spl: eMMC/SD: Provide one __weak spl_boot_mode() function") breaks the boot on several i.MX6 boards, such as cuboxi and wandboard: U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300) Trying to boot from MMC1 Failed to mount ext2 filesystem... spl_load_image_ext: ext4fs mount err - 0 Partially revert it so that we can boot U-Boot again on these i.MX6 platforms. Reported-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Breno Lima <breno.lima@nxp.com>
2018-02-24rockchip: clk: rk3399: handle set_rate/get_rate for PLL_PPLLPhilipp Tomsich
The device-tree node for the PMU clk controller assigns to its parent (i.e. PLL_PPLL) even though this clock currently is set up statically by an init-function. In order to avoid unexpected failures, a simple implementation of set_rate (which accepts requests, but notifies the caller of the preset frequency in its return value) and get_rate (which always returns the preset frequency) are added. Note that this is required for the RK808 PMIC to probe successfully on the RK3399-Q7, following the support for the assigned-clocks property. References: commit f4fcba5c5baa ("clk: implement clk_set_defaults()") Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2018-02-24rockchip: rk3288: Fix wrong TPL_TEXT_BASEJagan Teki
TPL offset 0xff704004 is unaligned address which is adding nearest 8-bytes for next instruction, So 0xff704004 is adding 0x20 for proper alignment which is causing the next instruction data 0xefffffff is moved. Hexdump with overlaped bytes: ----------------------------- 0000000 0000 0000 0000 0000 0000 0000 0000 0000 0000010 0000 0000 0000 0000 0000 0000 ffff eaff So, Fix the TEXT_BASE for proper aligned address 0xff704000 Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-02-24rockchip: rk3288: Add TPL_LDSCRIPTJagan Teki
Due to size limitations in SPL by adding falcon mode, rk3288 support TPL. In order to not overlap SPL_TEXT_BASE add TPL_TEXT_BASE with u-boot-tpl.lds that intern call u-boot-spl.lds with proper TEXT_BASE values. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-02-24rockchip: clk: rk3368: handle clk_enable requests for GMACPhilipp Tomsich
Since commit ba1f96672522 ("net: designware: add clock support"), the designware GMAC driver enables all referenced clocks. While this is a no-op for the RK3368 during boot-up (reset behaviour has all the clock gates open anyway), we still need to handle the clock-ids passed in the enable op of the clock-driver and return a success. This change extends the RK3368 clk driver to: (a) provide a enable op (b) signals success to the caller when the clocks for the GMAC are enabled (no actual action is necessary as the gates are open after reset) References: commit ba1f96672522 ("net: designware: add clock support") Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2018-02-24rockchip: clk: rk3399: handle clk_enable requests for GMACPhilipp Tomsich
Since commit ba1f96672522 ("net: designware: add clock support"), the designware GMAC driver enables all referenced clocks. While this is a no-op for the RK3399 during boot-up (reset behaviour has all the clock gates open anyway), we still need to handle the clock-ids passed in the enable op of the clock-driver and return a success. This change extends the enable-op of the rk3399 clk driver to signal success to the caller when the clocks for the GMAC are enabled. References: commit ba1f96672522 ("net: designware: add clock support") Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2018-02-24ARM: dts: i.MX6QDL: icore-rqs: Fix eMMC detection during SPLJagan Teki
usdhc4 has eMMC on icore-rqs boards, SPL is not detecting it becuase of u-boot,dm-spl flag so add it to make eMMC working. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-02-24Remove CONFIG_SYS_BOOTCOUNT_SINGLEWORDAlex Kiernan
Tidy up CONFIG_SYS_BOOTCOUNT_SINGLEWORD from the whitelist as there's no remaining uses of it left. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Migrate CONFIG_BOOTCOUNT_ALEN to KconfigAlex Kiernan
Convert CONFIG_BOOTCOUNT_ALEN to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Migrate generic bootcount to KconfigAlex Kiernan
Make generate boot counter selected in the same way as other boot count drivers Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Integrate AT91 bootcount driverAlex Kiernan
Integrate Boot counter for Atmel AT91SAM9XE into Kconfig Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Convert CONFIG_BOOTCOUNT_EXT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_EXT Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Convert CONFIG_BOOTCOUNT_I2C to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_I2C Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_RAM to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_RAM Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_ENV to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_ENV Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_AM33XX to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_AM33XX Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Prepare for multiple bootcount driversAlex Kiernan
Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Merge CONFIG_BOOTCOUNT and CONFIG_BOOTCOUNT_LIMITAlex Kiernan
CONFIG_BOOTCOUNT was only used in mx53ppd, merge it with CONFIG_BOOTCOUNT_LIMIT Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Ian Ray <ian.ray@ge.com>
2018-02-24Merge git://git.denx.de/u-boot-videoTom Rini
2018-02-23Remove config_distro_defaults.hAdam Ford
With the contents of config_distro_defaults.h migrated to Kconfig, we can remove this header file completely Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-23Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23rockchip: video: update MAINTAINERSPhilipp Tomsich
The video drivers (VOP, HDMI encoder, LVDS encoder, MIPI encoder) for Rockchip SOCs are self-contained and are mainly impacted by other changes in the architecture support (e.g. pinctrl, clocking, etc). Let's add these to the list of files maintained as part of the Rockchip port. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-02-23rockchip: video: rk_vop: migrate to livetreePhilipp Tomsich
This migrates rk_vop (the shared functions used by multiple VOP mini-drivers) to be compatible with a live tree. Unfortunately, there's (i) a lot of tree traversal needed for a VOP (as each active VOP vnode references back to the endpoints in the encoders and vice versa) to configure the connection between VOPs and encoders; (ii) the DTS binding is not too sane and one needs to walk a node's parents (the original code just assumed that the device would live 3 levels above the property linked through a phandle) until a UCLASS_DISPLAY device can be found. As part of the migration, the code for finding the enclosing display device has been changed to not assume a specific depth of nesting (i.e. we walk until we reach the root or find a matching device) and to use the newly introduced (in the same series) ofnode_get_parent() function. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-02-23rockchip: video: rk_hdmi: migrate to livetreePhilipp Tomsich
The rk_hdmi (shared functions for multiple HDMI mini-drivers) has been using devfdt_get_addr() to read the HDMI controller's IO base address. This will cause a failure with a live tree. This changes the driver to use dev_read_addr() which is safe both for flat trees and live trees. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-02-23core: add ofnode_get_by_phandle() apiKever Yang
We need to get ofnode from a phandle, add interface to support both live dt and fdt. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-02-23core: ofnode: add ofnode_get_parent functionPhilipp Tomsich
The Rockchip video drivers need to walk the ofnode-parrents to find an enclosing device that has a UCLASS_DISPLAY driver bound. This adds a ofnode_get_parent()-function that returns the parent-node. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-02-23Merge git://git.denx.de/u-boot-shTom Rini
2018-02-23Merge git://git.denx.de/u-boot-usbTom Rini
2018-02-23config_whitelist: remove false-positive CONFIG optionsMasahiro Yamada
U-Boot pulled in several core makefiles from Linux. The following are not used in U-Boot: - CONFIG_DEBUG_SECTION_MISMATCH - CONFIG_FTRACE_MCOUNT_RECORD - CONFIG_GCOV_KERNEL - CONFIG_GCOV_PROFILE_ALL - CONFIG_KASAN - CONFIG_MODVERSIONS We can remove the unused code if we like. (although it will get the scripts out of sync) CONFIG_BOOM and CONFIG_HIS_DRIVER are just mentioned in the comment block of scripts/basic/fixdep.c CONFIG_SHELL is not configuration, but a variable for internal-use. It is just a historical misnomer in Kbuild. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-02-23omap3_logic: Fix Environmental locationAdam Ford
For the omap3_logic boards, the environment is always in NAND. This removes the ENV_IS_IN_FAT flag to eliminate the extra chatter. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-23sf: Add ISSI IS25LP256 entryMarek Vasut
Add entry for ISSI IS25LP256 part. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@openedev.com>
2018-02-23Makefile: Don't mess with .text section location for selected archesAlexey Brodkin
Most of architectures have .text section situated in the very beginning of U-Boot binary and thus it is very logical that CONFIG_SYS_TEXT_BASE is used on final linkage step to specify where U-Boot gets linked to. For that we pass the following construction to the LD: ---------------------------->8----------------------- xxx-ld ... -Ttext $(CONFIG_SYS_TEXT_BASE) ... ---------------------------->8----------------------- But there could be exceptions. For example: 1. In case of ARCv2 we want to put vectors table in its own section .ivt in front of .text section which means we need either add an offset to CONFIG_SYS_TEXT_BASE to compensate for .ivt or don't pass "-Ttext" to the LD at all and specify link base in linker script directly. 2. Some architectures even though have .text section in the very beginning of the U-Boot image still use different symbols to specify link-base: * NIOS2: CONFIG_SYS_MONITOR_BASE (which I really like because that exactly what makes sense - where out image starts but not beginning of its .text section which just happened to match the whole image beginning) * EXTENSA: CONFIG_SYS_TEXT_ADDR * X86: Which doesn't use CONFIG_SYS_MONITOR_BASE in case of EFI otherwise sets explicit link base in u-boot.lds I think that's good to allow for flexibility and don't require each and every architecture or even platform to specify CONFIG_SYS_TEXT_BASE as well as use it to set .text section location. So let's only pass "-Ttext xxx" for those architectures who don't set link-base explicitly in their linker scripts. This patch iaddresses comments for previously sent https://patchwork.ozlabs.org/patch/867540/. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
2018-02-23arm64: show_regs: Dump the LRs HW valuesKarl Beldan
These were dropped in [1], after relocation, for their values offset by reloc_off. Unconditionally show the HW values and add a '(reloc)' hint for the offset values showed after relocation. Also, the LRs' dumps are now formatted the same way the other regs' are. [1] Commit 082693f4 ("arm64 :show_regs: show the address before relocation") Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
2018-02-23tools/kwbimage: fix LibreSSL buildJonathan Gray
Fix build after addition of RSA_get0_key() to LibreSSL. Patch from Theo Buehler and Stuart Henderson. Signed-off-by: Theo Buehler <tb@openbsd.org> Signed-off-by: Stuart Henderson <sthen@openbsd.org>
2018-02-23net: Remove Xilinx ll_temac driverMichal Simek
ll_temac driver was used by Xilinx Microblaze big endian and Xilinx ppc405/ppc440 SoCs. ppc support was removed by: "powerpc: remove 4xx support" (sha1: 98f705c9cefdfdba62c069821bbba10273a0a8ed) and Microblaze BE is not tested for a long time that's why this driver can be removed because none is going to updated it to DM anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-23configs: am335x_evm_usbspl: Add CONFIG_SPL_NET_VCI_STRINGFaiz Abbas
Add CONFIG_SPL_NET_VCI_STRING to enable USB-Ethernet boot mode support. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-23fdt: Fixup only valid memory banksThierry Reding
Memory banks with address 0 and size 0 are empty and should not be passed to the OS via device tree. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-02-23ns16550: Fix mem mapped endian checkBernhard Messerklinger
Do a explicit check for CONFIG_SYS_BIG_ENDIAN and CONFIG_SYS_LITTLE_ENDIAN to avoid errors on platforms where both are undefined (x86). Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2018-02-23pci: Fix decode regions for memory banksBernhard Messerklinger
Since memory banks may not be located behind each other we need to add them separately. Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2018-02-23defconfig: k2x_hs_evm: Re-enable TI_SECURE_DEVICE in HS K2x partsAndrew F. Davis
These got removed in config re-syncs due to a Kconfig bug. Add these back here. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-02-23env: Fix missed getenv_ulong to env_get_ulong conversionAndrew F. Davis
This seems to have been missed, possibly due to the inability to enable TI_SECURE_DEVICE on Keystone2 devices previously. Fixes: bfebc8c965e4 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()") Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-08-28 01:14:01 +0000