summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-08-05mmc: use the generic error numberJaehoon Chung
Use the generic error number instead of specific error number. If use the generic error number, it can debug more easier. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-08-05mmc: fsl_esdhc: remove the duplicated header fileJaehoon Chung
"mmc.h" is already included. It's duplicated. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-05mmc: dw_mmc: remove the duplicated header fileJaehoon Chung
<asm-generic/errno.h> is already included in <errno.h>. It can use <errno.h> instead of <asm-generic/errno.h> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-05mmc: s5p_sdhci: unset the SDHCI_QUIRK_BROKEN_R1BJaehoon Chung
Unset the SDHCI_QUIRK_BROKEN_R1B for exynos SoC. (Tested on Exynos4 Boards.) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2016-08-05mmc: sdhci: set to INT_DATA_END when there are dataJaehoon Chung
There is no data, it doesn't needs to wait for completing data transfer. (It seems that it can be removed.) Almost all timeout error is occured from stop command without data. After applied this patch, I hope that we don't need to increase timeout value anymore. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2016-08-05mmc: sdhci: clean up timeout detectionMasahiro Yamada
The current timeout detection logic is not very nice; it calls get_timer(start) in the while() loop, and then calls it again after the loop to check if a timeout error happened. Because of the time difference between the two calls of get_timer(), the timeout detected after the loop may not be true. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-08-03powerpc/86xx: Increase boot map size to 256 MiBScott Wood
This is what Linux maps on classic PPC during boot, and modern kernel images don't fit within the current 8 MiB uncompressed limit. Adjust image load addresses to be above this limit to avoid conflicts. Signed-off-by: Scott Wood <oss@buserror.net> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-08-02ARMv8/fsl-ppa: Consolidate PPA image stored-media flag for XIPHou Zhiqiang
The PPA binary may be stored on QSPI flash instead of NOR. So, deprecated CONFIG_SYS_LS_PPA_FW_IN_NOR in favour of CONFIG_SYS_LS_PPA_FW_IN_XIP to prevent fragmentation of code by addition of a new QSPI specific flag. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02arm/PSCI: Add support for creating ARMv7 PSCI version 1.0 DT nodeHou Zhiqiang
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02arm/PSCI: Fixed the backward compatiblity issueHou Zhiqiang
Appended the compatible strings of old version PSCI to the latest version supported. And there are some psci functions' property must be added to DT only for psci version 0.1, including cpu_on, cpu_off, cpu_suspend, migrate. Note, ARMv8 Secure Firmware Framework doesn't support PSCI ver 0.1. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02arm/PSCI: Removed unused codeHou Zhiqiang
Identify the PSCI node only by its name, so removed the code finding it by compatible string. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02driver/ddr/fsl: Fix timing_cfg_2York Sun
Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the change was wrong. wr_lat has 5 bits with MSB at [13] and lower 4 bits at [9:12], in big-endian convention. Signed-off-by: York Sun <york.sun@nxp.com> Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
2016-08-02board/freescale: Update MAINTAINERS filesYork Sun
Update maintainers for secure boot targets. Signed-off-by: York Sun <york.sun@nxp.com>
2016-08-02armv8: ls1043a: enable pxe commandsWenbin Song
Enable pxe command for ls1043ardb and ls1043aqds. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02armv8: ls1012a: Update Refresh cycle for DDRPrabhakar Kushwaha
Refresh cycle value must be selected based on the frequency of DDR. tREFI = 7.8 us as per JEDEC. The value for MDREF[REF_CNT] should be based on round up (tREFI/tCK) formula. For 500MHz, mdref value should be 0x0f3c8000. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02armv8: ls1012a: Enable DDR row-bank-column decodingPrabhakar Kushwaha
Enable DDR row-bank-column decoding to decode DDR address as row-bank-column instead of bank-row-column for improving performance of serial data transfers. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02board: ls1012aqds: Update LBMAP_MASK and RST_CTL_RESETPrabhakar Kushwaha
qixis_reset altbank usagge ~QIXIS_LBMAP_MASK in code. So define inverse value QIXIS_LBMAP_MASK. Also, update QIXIS_RST_CTL_RESET value to keep RST_CTL[REQ_MOD] as 0b11 i.e. PORESET during qixis_reset Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02crypto/fsl: Update blob cmd to accept 64bit addressesSumit Garg
Update blob cmd to accept 64bit source, key modifier and destination addresses. Also correct output result print format for fsl specific implementation of blob cmd. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02driver: spi: fsl-qspi: remove compile WarningsYunhui Cui
Warnins log: drivers/spi/fsl_qspi.c: In function ‘qspi_ahb_read’: drivers/spi/fsl_qspi.c:400:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] memcpy(rxbuf, (u8 *)(priv->cur_amba_base + priv->sf_addr), len); Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02powerpc/mpc85xx: Update erratum workaround for A006379York Sun
Update erratum workaround for A006379 to set register CPCHDBCR0 with value 0x001e0000, replacing the old value 0x003c0000. Signed-off-by: York Sun <york.sun@nxp.com> Reported-by: Dave Liu <dave.liu@nxp.com>
2016-08-02Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-08-02MAINTAINERS, git-mailrc: Update the mmc maintainerJaehoon Chung
Update the mmc maintainer from Pantelis to me. Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-08-02ARM64: zynqmp: Do not enable DM_MMC by defaultMichal Simek
The patch: "dm: mmc: zynq: Convert zynq to use driver model for MMC" (sha1: 329a449f2c289b4de8f892fca1d9379ce5fd81b8) added dependency on enabling some MMC options by default. There are minimal ZynqMP configurations which require only minimal configurations to be enabled to keep u-boot size as lower as possible. Move options to defconfig instead. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-08-02ARM64: zynqmp: Fix stack pointer initializationSoren Brinkmann
This partly reverts commit: "ARM64: zynqmp: Add SPL support support" (sha1: e6a9ed04e78cf87ec97e306fa4e7a1669ef98df6) Stack can rewrite ATF code. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-08-02ARM64: zynqmp: Define config USB_STORAGE through defconfigMichal Simek
Define config USB_STORAGE through defconfig for all Xilinx ZynqMP boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-08-02xilinx: Sync defconfigs with the latest Kconfig layoutMichal Simek
Update Microblaze, Zynq and ZynqMP defconfigs to reflect latest Kconfig changes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-08-02ARM64: zynqmp: Wire up PSCI resetMichal Simek
Using PSCI to reset the system. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-08-01ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodesMichal Simek
Serial driver is getting clk information via DT that's why also clk node needs to have this flag. Different behavior was introduced by: "dm: Use dm_scan_fdt_dev() directly where possible" (sha1: 911954859d6dece49c3e4835faea004cfe392506) where simple-bus driver starts to call dm_scan_fdt_dev() which has additional logic around pre_reloc_only parameter which exclude clk nodes. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-31Drop references to MAKEALL in the documentationSimon Glass
It is confusing to mention MAKEALL when it is not the normal way of building U-Boot anymore. Update the documentation to suit. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31Drop the MAKEALL toolSimon Glass
Buildman has been around for 3 years now. It has had a lot of use and testing. Perhaps it is time to remove MAKEALL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31buildman: Add a quick-start noteSimon Glass
For those who just want to build a board, it is useful to see a quick hint right at the start of the documentation. Add a few commands showing how to download toolchains and build a board. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-31buildman: Avoid overwriting existing toolchain entriesSimon Glass
The current code for setting up the toolchain config always writes the new paths to an item called 'toolchain'. This means that it will overwrite any existing toolchain item with the same name. In practice, this means that: buildman --fetch-arch all will fetch all toolchains, but only the path of the final one will be added to the config. This normally works out OK, since most toolchains are the same version (e.g. gcc 4.9) and will be found on the same path. But it is not correct and toolchains for archs which don't use the same version will not function as expected. Adjust the code to use a complete glob of the toolchain path. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31buildman: Drop the toolchain error when downloading toolchainsSimon Glass
It doesn't make sense to complain about missing toolchains when the --fetch-arch option is being used. The user is presumably aware that there is a toolchain problem and is actively correcting it by running with this option. Refactor the code to avoid printing this confusing message. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-31buildman: Fix a typo in TestSettingsHasPath()Simon Glass
The function comment should say 'buildman'. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31buildman: Improve the toolchain progress/error outputSimon Glass
Use colour to make it easier to see what is going on. Also print a message before downloading a new toolchain. Mention --fetch-arch in the message that is shown when there are no available toolchains, since this is the quickest way to resolve the problem. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31buildman: Allow the toolchain error to be suppressedSimon Glass
When there are no toolchains a warning is printed. But in some cases this is confusing, such as when the user is fetching new toolchains. Adjust the function to supress the warning in this case. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-31buildman: Fix the 'help' test to use the correct pathSimon Glass
When buildman is run via a symlink, this test fails. Fix it to work the same way as buildman itself. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-31buildman: Automatically create a config file if neededSimon Glass
If there is no ~/.buildman file, buildman currently complains and exists. To make things a little more friendly, create an empty one automatically. This will not allow things to be built, but --fetch-arch can be used to handle that. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31buildman: Tidy up the README a littleSimon Glass
Tidy up some problems found by a recent review. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31libfdt: Introduce new ARCH_FIXUP_FDT optionMichal Simek
Add new Kconfig option to disable arch_fixup_fdt() calls for cases where U-Boot shouldn't update memory setup in DTB file. One example of usage of this option is to boot OS with different memory setup than U-Boot use. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31Merge git://git.denx.de/u-boot-rockchipTom Rini
2016-07-31sunxi: Re-enable h3 emac supportHans de Goede
With the recent bug fixes for the sun8i_emac driver all known issues are resolved, so we can re-enable the driver. While at it, also enable the emac on the Orange Pi One. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Jagan Teki <jteki@openedev.com>
2016-07-31net: sun8i_emac: Fix DMA alignment issues with the rx / tx buffersHans de Goede
This fixes the following CACHE warnings when using sun8i_emac: => dhcp BOOTP broadcast 1 BOOTP broadcast 2 CACHE: Misaligned operation at range [7bf594a8, 7bf59628] BOOTP broadcast 3 CACHE: Misaligned operation at range [7bf59c90, 7bf59e10] CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8] DHCP client bound to address 10.42.43.80 (1009 ms) Note this commit also changes the max rx size from 2024 to 2044, matching what the kernel driver uses. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31sunxi: On newer SoCs use words 1-3 instead of just word 3 from the SIDHans de Goede
It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID are always 0 on H3 making it a poor candidate to use as source for the serialnr / mac-address, and the other non constant words (1 and 2) also have quite a few bits which are the same for some boards, This commits switches to using the crc32 of words 1 - 3 to get a more unique value for the mac-address / serialnr. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31sunxi: Ensure that the NIC specific bytes of the mac are not all 0Hans de Goede
On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to the NIC specific bytes of the mac all being 0, which leads to the boards not getting an ipv6 address from the dhcp server. This commits adds a check to ensure this does not happen. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31sunxi: Hummingbird_A31_defconfig: Drop MACPWR optionChen-Yu Tsai
MACPWR was used to bring the Ethernet PHY out of reset. The designware driver now supports the phy reset gpio binding, so this is no longer needed. In fact in requesting the same GPIO, it makes the designware driver fail to probe. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-31sunxi: gpio: Add .xlate function for gpio phandle resolutionChen-Yu Tsai
sunxi uses a 2 cell phandle for gpio bindings. Also there are no seperate nodes for each pin bank. Add a custom .xlate function to map gpio phandles to the correct pin bank device. This fixes gpio_request_by_name usage. Fixes: 7aa974858422 ("dm: sunxi: Modify the GPIO driver to support driver model") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-31rockchip: add support for rk3288 PopMetal boardjk.kernel@gmail.com
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and Gigabit Ethernet. Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31rockchip: add basic support for fennec-rk3288 boardjk.kernel@gmail.com
Fennec is a RK3288-based development board with 2 USB ports, HDMI, micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access to display pins, I2C, SPI, UART and GPIOs. Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-10 20:16:03 +0000