summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-07-23imx: i.mx6q: imx6q_logic: Migrate to SPL and enable SDPAdam Ford
Since the vast majority of i.MX6 boards are migrating to SPL, this patch converts im6q_logic to SPL and enables the SDP for loading SPL and u-boot.img over USB. The Falcon mode only supports NAND flash as of now due to limited space/RAM, but all i.MX6D/Q SOM's from Logic PD have internal NAND from which to boot. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23ARM: imx6: DHCOM i.MX6 PDK: ddr init for 32bit bus and 4GBit chipsLudwig Zenz
Support 1GIB + 2GIB DDR3 with 64bit bus width and 512MIB + 1GIB with 32bit bus width Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
2018-07-23ARM: imx6: configure ddrcode pins in spl DHCOM i.MX6 PDKLudwig Zenz
Preperation for conditional DDR3 initialization based on GPIO codes. Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
2018-07-23Revert "ARM: imx6: Disable DDR DRAM calibration DHCOM i.MX6 PDK"Ludwig Zenz
This reverts commit a637fe6f27fd4c19ef9f43a5f871c244581422ac. The DDR DRAM calibration was enhanced by write leveling correction code. It can be used with T-topology now. Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
2018-07-23pico-imx7d: Add new pico-pi configOtavio Salvador
The new config skips the boot menu which asks which board is in use. This is useful to allow direct booting of image without user iteration. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: README: Drop old instructions about secure modeOtavio Salvador
Our default config already has the secure mode supported, so the manual step is not required anymore. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: README: Use dfu-util to flash U-BootOtavio Salvador
The DFU allows a more user friendly use as the details where the bootloader is installed are abstracted. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Enable auxiliary code supportOtavio Salvador
This enables the "bootaux" command so a firmware can be loaded inside the M4 MCU. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Allow default fdtfile to be overridden by defconfigOtavio Salvador
This allow the addition of extra default configurations for each baseboard, removing the boot menu when user boots for the first time. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Do not override addrmap5Fabio Estevam
The addrmap5 value is the same for the 512MB and 1GB variants, so there is no need to override it. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Enable CONFIG_ARMV7_BOOT_SEC_DEFAULTFabio Estevam
Currently the CAAM driver fails to be probed: caam 30900000.caam: Entropy delay = 3200 caam 30900000.caam: failed to acquire DECO 0 caam 30900000.caam: failed to instantiate RNG CAAM needs to be initialized in secure world, so enable CONFIG_ARMV7_BOOT_SEC_DEFAULT to allow the driver to probe successfully. Tested with kernel mainline version 4.17.2. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add Falcon mode supportFabio Estevam
Falcon mode boots the kernel directly from SPL, without loading the full U-Boot. As pico-imx7d does not have a GPIO for selecting Falcon versus normal mode, enter in Falcon mode when the customer selects the CONFIG_SPL_OS_BOOT option in menuconfig. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add bootmenu to choose the baseboardOtavio Salvador
Currently the baseboards do not offer a way to autodetect which one is in use, so we ask the user if no value has been set. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add support for update SPL using DFUFabio Berton
Add spl entry on dfu_alt_info to be able to update U-Boot with SPL for pico imx7d board. Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add SPL supportFabio Estevam
Convert pico-imx7d to SPL support. There are two variants of pico-imx7d SOMs: - One with 512MB of RAM - One with 1GB of RAM The 512MB module contains two Hynix H5TC2G63GFR-PBA. The 1GB module contains two Hynix H5TC4G63GFR-PBA. The RAM size is determined in runtime by reading GPIO1_12. While at it, also add USB Serial Download mode support as it is very helpful for loading SPL and u-boot.img via imx_usb_loader. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add fastboot supportFabio Estevam
fastboot tool is a convenient way to flash the eMMC, so add support for it. Examples of usages: On the pico-imx7d U-Boot prompt: => fastboot 0 On the Linux PC connected via USB: 1. Retrieving the U-Boot version $ sudo fastboot getvar bootloader-version -i 0x0525 bootloader-version: U-Boot 2018.07-rc1-03888-gde846f9 finished. total time: 0.000s 2. Resetting the board $ sudo fastboot reboot -i 0x0525 (this causes the pico-imx7d to reboot) Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add default DFU targetsOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add GPT partitioning supportOtavio Salvador
This allow the use of: > run setup_emmc inside of the U-Boot prompt to do the partitioning of the disk. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Fix common distro configuration behaviorOtavio Salvador
This sets DISTRO_CONFIG and BOOTCOMMAND, as well as add a `finduuid` environment helper to allow it to properly work with Yocto Project and other distributions using extlinux autogenerated configuration files. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Convert to distro configFabio Estevam
Instead of keeping a custom environment, use a more generic approach by switching to disto config. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23arm, imx6: add alternative PAD_CTL_DSE constantsMark Jonas
Not all i.MX6 pads use the same drive strength table. So far only the 240 Ohm to 34 Ohm table was available. Because the constants used have speaking names it can be confusing to use e.g. PAD_CTL_DSE_48ohm when according to the reference manual 52 Ohm is the correct value. This patch adds the 260 Ohm to 37 Ohm table. For example, the IOMUXC_SW_PAD_CTL_PAD_SD2_CLK register (SD-card clock) uses the added table. Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-07-23colibri_imx7: improve DDR3 timingStefan Agner
This makes sure that all Colibri iMX7 modules work with the same timing. The changes are: - Disable ODT on read (JEDEC standard JESD79-3F says in chapter 5.2.3 ODT during Reads: "As the DDR3 SDRAM can not terminate and drive at the same time, RTT must be disabled at least half a clock cycle..." and also MX7D SABRESD is disabling it) This alone fixed memory issues for two Colibri iMX7 1GB modules which showed issues before - Make sure tRFC(min) is at least 260ns - Make sure tRC is >50.625ns - tRP needs to be >13.125ns, we can lower from 18.75ns to 15ns - tFAW is not relevant, leave at reset Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-07-23colibri_imx7: add compatible string used in vanilla LinuxStefan Agner
Device trees from vanilla Linux do not specify a i.MX 7 specific compatible string. Make sure to set partitions also when booting upstream Linux. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23mx6cuboxi: Move the default environment for all devicesJon Nettleton
Previously we had stored the environment right after the u-boot.img on the disk. I never liked this because with dtbs being included and such the image could grow in size. Instead we move the environment to be negatively offset from the 1MB mark. Almost all our images start at 4MB's, and most standard images start at 1MB, and all our storage devices are a minimum 1MB. Therefore we can store env there for all classes of devices and have plenty of space in case u-boot.img needs to grow. Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-07-23imx: mx7: psci: implement MIGRATE_INFO_TYPEStefan Agner
Implement MIGRATE_INFO_TYPE. This informs Linux that no migration for the trusted operating system is necessary: [ 0.000000] psci: Trusted OS migration not required Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23imx: mx7: psci: support CPU0 on/offStefan Agner
So far psci_cpu_(on|off) only worked for CPU1. Allow to control CPU0 too. This allows to run the Linux PSCI checker successfully: [ 2.213447] psci_checker: PSCI checker started using 2 CPUs [ 2.219107] psci_checker: Starting hotplug tests [ 2.223859] psci_checker: Trying to turn off and on again all CPUs [ 2.267191] IRQ21 no longer affine to CPU0 [ 2.293266] Retrying again to check for CPU kill [ 2.302269] CPU0 killed. [ 2.311648] psci_checker: Trying to turn off and on again group 0 (CPUs 0-1) [ 2.354354] IRQ21 no longer affine to CPU0 [ 2.383222] Retrying again to check for CPU kill [ 2.392148] CPU0 killed. [ 2.398063] psci_checker: Hotplug tests passed OK [ 2.402910] psci_checker: Starting suspend tests (10 cycles per state) [ 2.410019] psci_checker: cpuidle not available on CPU 0, ignoring [ 2.416452] psci_checker: cpuidle not available on CPU 1, ignoring [ 2.422757] psci_checker: Could not start suspend tests on any CPU [ 2.429370] psci_checker: PSCI checker completed Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23imx: mx7: psci: provide complete PSCI 1.0 implementationStefan Agner
PSCI 1.0 require PSCI_VERSION, PSCI_FEATURES, AFFINITY_INFO and CPU_SUSPEND to be implemented. Commit 0ec3d98f7692 ("mx7_common: use psci 1.0 instead of 0.1") marked the i.MX 7 implementation to be PSCI 1.0 compliant but failed to implement those functions. Especially the missing PSCI version callback was noticeable when booting Linux: [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv65535.65535 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 This patch provides a minimal implementation thereof. With this patch applied Linux detects PSCI 1.0: [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 Fixes: 0ec3d98f7692 ("mx7_common: use psci 1.0 instead of 0.1") Suggested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23imx: mx7: psci: use C code exclusivelyStefan Agner
There is no need for assembly in the platform specific part of the PSCI implementation. Note that this does not make it a complete PSCI 1.0 implementation yet but aids to do so in upcoming patches. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23ARM: PSCI: initialize stack pointer on secondary CPUsStefan Agner
A proper stack is required to safely use C code in psci_arch_cpu_entry. Fixes: 486daaa618e1 ("arm: psci: add a weak function psci_arch_cpu_entry") Cc: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Patrick DELAUNAY <Patrick.delaunay@st.com> Tested-by: Patrick DELAUNAY <Patrick.delaunay@st.com>
2018-07-23arm: imx7d: cl-som-imx7: sf: support all SF typesUri Mashiach
Enable the support for all SPI flash types. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
2018-07-23i.MX6: engicam: gpr_init can be called only for some architectureMichael Trimarchi
Fix an invalid usage of the gpr_init function for the imx6ul architecture Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-23imx: imx6: Add comment to gpr_init functionMichael Trimarchi
This function can be used only for some of the nxp SoC. Make it explicit in the comment. This adjust a bit commit 3aa4b703b483f165dd ("imx: imx6: Move gpr_init() function to soc.c") Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-23mx7: Remove BMODE supportFabio Estevam
i.MX7 does not support BMODE due to the erratum e10574 ("Watchdog: A watchdog timeout or software trigger will not reset the SOC"), so remove its support. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-07-23imx: mx6: Fix implementantion reset_miscMichael Trimarchi
lcdif_power_down should not be included in spl build to avoid build failure introduced by commit eb111bb31d882877e75e6b8083808dcaf6493b92 Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2018-07-23eth: dm: fec: Add gpio phy reset bindingMichael Trimarchi
Add the missing gpio phy reset binding to the gpio and reset time configuration Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-23mx6cuboxi: Add emmc device tree suffixJon Nettleton
Mainline and now the SolidRun 4.9 nxp based tree use the new reorganization of device-tree files that separate out the emmc into its own dtb. u-boot will now look for -emmc in the device tree name if one is detected. Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-23mx6cuboxi: Use mmc_get_op_cond() to check for an eMMCJon Nettleton
Previously we had just made broad assumptions with which of our boards had an eMMC or not even though this is a manufacturing time assembly option. This takes the guessing away and actually checks for the existence of an eMMC and sets up the has_emmc environment variable. Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-23mx6cuboxi: drop CONFIG_SYS_FSL_USDHC_NUMBaruch Siach
This macro is not used. Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-23mx6cuboxi: Add support for eMMC bootingJon Nettleton
The HB2 boards as well as rev 1.5 soms support eMMC booting as well as SDHC. Add the infrastructure to support booting these devices. Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-23mmc: break out get_op_cond code to its own functionJon Nettleton
This code is useful for testing the existance of devices that do not have card detect capabilities. This breaks out the core functionality and leaves the actual init logic and error reporting in mmc_start_init(). Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-07-23mmc: drop mention of IN_PROGRESS statusBaruch Siach
The IN_PROGRESS macro has been removed in commit bd47c13583f (mmc: Fix splitting device initialization). Remove it from the mmc_start_init() function description. Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-23board: toradex: add Colibri iMX6ULL supportStefan Agner
Add support for the Colibri iMX6ULL module which comes with on-board raw NAND. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23board: toradex: add new and upcoming SKUsStefan Agner
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23ARM: dts: imx6ull: use same compatible string as Linux is usingStefan Agner
The GPMI NAND IP seems to be the same as used in i.MX 6Quad. Use the fsl,imx6q-gpmi-nand compatible string like Linux devices trees are. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23imx: add macro to detect whether USB has been initializedStefan Agner
This macro allows to detect whether the boot ROM initialized USB already (serial downloader). This is helpful to reliably detect if the system has been recovered via USB serial downloader. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-07-23mtd: nand: mxs_nand: add device tree support for i.MX 6Stefan Agner
Support i.MX 6 NAND GPMI driver data from device tree. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23bootcount: flush after storing the bootcounterStefano Babic
If the bootcounter address is in a cached memory, a flush of dcache must occur after updateing the bootcounter. Issue found on i.MX6 where bootcounter is put into the internal (cached) IRAM. Signed-off-by: Stefano Babic <sbabic@denx.de>
2018-07-21env: Simplify Makefile using $(SPL_TPL_)York Sun
Add Kconfig options SPL_ENV_* and TPL_ENV_* and simplify Makefile. This allows SPL/TPL image has different environment setting from full feature U-Boot. Signed-off-by: York Sun <york.sun@nxp.com>
2018-07-21env: typo in description of ENV_IS_IN_REMOTEHeinrich Schuchardt
%s/remove/remote/ Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-07-20Merge branch 'master' of git://git.denx.de/u-boot-rockchipTom Rini
generated by cgit v1.2.3 (git 2.0.4) at 2024-10-05 17:25:51 +0000