summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-07-24ppc4xx: Add chip_config command to AMCC Kilauea eval boardStefan Roese
This patch removes the "alterpll" command and replaces it with the now ppc4xx standard "chip_config" command to configure the I2C bootstrap EEPROM. Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Fix EEPROM configuration on KilaueaStefan Roese
Kilauea has an AT24C02 EEPROM which has an 8 byte page. Without defining CONFIG_SYS_EEPROM_PAGE_WRITE_BITS to 3 the "eeprom" command doesn't work correctly. Additionally the page write delay (CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS) is set to a more defensive value of 10ms. Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Add 405EP based PMC405DE boardMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Add struct for 4xx GPIO controller registersMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Replace 4xx lowercase SPR referencesMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24Add "chip_config" command for PPC4xx bootstrap configurationStefan Roese
This patch adds a generic command for programming I2C bootstrap eeproms on PPC4xx. An implementation for Canyonlands board is included. The command name is intentionally chosen not to be PPC4xx specific. This way other CPU's/SoC's can implement a similar command under the same name, perhaps with a different syntax. Usage on Canyonlands: => chip_config Available configurations (I2C address 0x52): 600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100 600-nand - NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100 800-nor - NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100 800-nand - NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100 1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100 1000-nand - NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100 1066-nor - NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88 *** 1066-nand - NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88 => chip_config 600-nor Using configuration: 600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100 done (dump via 'i2c md 52 0.1 10') Reset the board for the changes to take effect Other 4xx boards will be migrated to use this command soon as well. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Dirk Eibach <eibach@gdsys.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2009-07-24xpedite1k: Move to X-ES vendor directoryPeter Tyser
The XPedite1000 is an X-ES product thus it can be put in board/xes along with other X-ES boards. Along with the move, the board was renamed to XPedite1000 from XPedite1K to fit X-ES's standard naming convention. Maintainership was also transfered to Peter Tyser. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Sync checkboard() with other X-ES boardsPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Sync up board config options with other X-ES boardsPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Sync organization of board config with other X-ES boardsPeter Tyser
This change should have no functional effect Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Sync up commands and environment with other X-ES boardsPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Disable unused ethernet port 1Peter Tyser
The XPedite1000 only has 2 available ethernet ports: ppc_4xx_eth2 (EMAC2) and ppc_4xx_eth3 (EMAC3) Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Store environment in flashPeter Tyser
Previously an I2C EEPROM was used. The EEPROM had size, reliability, and access issues which are resolved by storing the environment in flash. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Add support for additional GPIO pinsPeter Tyser
Enable GPIO pins for an I2C EEPROM write protect, a system reset pin, and a PMC #MONARCH pin. These pins are not currently used in U-Boot, but are used in OSes and may be used in U-Boot in the future. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Add support for optional flashesPeter Tyser
The XPedite1000 can be built with 4 total flashes: - 512KB AMD socketed - 16MB Intel soldered - 2 x 32MB AMD MirrorBit flashes Add support for the optional 2 32MB CFI-compliant AMD flashes Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Cleanup coding stylePeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Remove support for reading MACs from EEPROMPeter Tyser
By default, the XPedite1000 comes installed with xMon, a proprietary bootloader. xMon stores its MAC address in an onboard EEPROM. Rather than requiring a non-standard location in the EEPROM to be reserved for MAC addresses, store the MAC addresses in U-Boot's standard environment. A U-Boot application or OS application can be used to migrate xMon MAC addresses to U-Boot's environment if necessary. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Remove support for fixed SDRAM configurationPeter Tyser
All XPedite1000's have SPD EEPROMs present and no fixed configuration parameters are currently defined or used Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Remove CONFIG_SYS_DRAM_TEST supportPeter Tyser
POST or command line tests provide similar functionality Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24xpedite1k: Use standard CFI flash driverPeter Tyser
Using the CFI flash driver will allow write access to the 16MB Intel StrataFlash present on the XPedite1000. The 512KB socketed (non CFI-compliant flash) will no longer be writable. The mapping of the 16MB Strata flash was moved to 0xff000000 and the 512KB AMD socketed flash was moved to 0xfe000000. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Cleanup PLU405 board codeMatthias Fuchs
Some Coding style cleanup (braces, whitespaces, long lines) Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Add DL-Vision 405EP board supportDirk Eibach
Board support for the Guntermann & Drunck DL-Vision. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Fix missing freqOPB for 405EPDirk Eibach
In cpu/ppc4xx/speed.c initialization of sysInfo->freqOPB for 405EP was left out for no obvious reason. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24ppc4xx: Fix TLB reset problem with recent 44x imagesStefan Roese
Patch d873133f [ppc4xx: Add Sequoia RAM-booting target] broke "normal" booting on some 44x platforms. This breakage is only noticed in some cases while powercycling. As it seems, the code in question in start.S didn't invalidate TLB #0. This makes sense since this TLB is used for the bootrom mapping. With the patch mentioned above even TLB #0 got invalidated resulting in an error later on. This patch now fixes this issue by only invalidating TLB #0 in the RAM- booting case. Tested succesfully on Sequoia and Canyonlands. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <Eibach@gdsys.de>
2009-07-23Coding Style cleanup; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-23autoconf.mk: include before config.mk for top level filesMike Frysinger
By including autoconf.mk before config.mk, all top level files can use any config options it sets up (like <arch>_config.mk) or the Makefile itself without being forced to use lazy evaluation.
2009-07-23Remove static declaration from gunzip_bmp()Mark Jackson
This patch removes the static declaration from gunzip_bmp() Without it, the gunzip_bmp() function is not visible to common/lcd.c and fails to compile with an error. Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
2009-07-23cmd_tsi148: General cleanupPeter Tyser
- Fix command help message - Disable DEBUG by default - Fix whitespace issues - Fix lines > 80 characters Signed-off-by: Peter Tyser <ptyser@gmail.com> Acked-by: Stefan Roese <sr@denx.de>
2009-07-23unify HOST_CFLAGS and HOSTCFLAGSMike Frysinger
The top build system sets up HOSTCFLAGS a bit and exports it, but other places use HOST_CFLAGS instead. Unify the two as HOSTCFLAGS so that the values stay in sync. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-23Update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-23update config for mvBC-P (MPC5200)André Schwarz
This patch adds I2C support for mvBC-P and defines flash layout matching the shipped product. Signed-off-by: André Schwarz <andre.schwarz@matrix-vision.de>
2009-07-23ahci: Fix gcc 4.4 compiler warningKumar Gala
ahci.c: In function 'ata_scsiop_read_capacity10': ahci.c:616: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-23drivers/bios_emulator: Fix gcc 4.4 compiler warningKumar Gala
biosemu.c: In function 'BE_setVGA': biosemu.c:147: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-23Re-add support for image type 'Standalone Program'Detlev Zundel
Support for this type was lost during the bootm refactoring. Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-07-23Add error checking for unsupported OS types.Detlev Zundel
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-07-23ppc: Unlock cache-as-ram in a consistent mannerPeter Tyser
Previously, non-e500 architectures only unlocked their data cache which was used as early RAM when booting to Linux using the "bootm" command. This change causes all PPC boards with CONFIG_SYS_INIT_RAM_LOCK defined to unlock their data cache during U-Boot's initialization. This improves U-Boot performance and provides a common cache state when booting to different OSes. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-07-23Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk
2009-07-23zlib: updated to v.1.2.3Giuseppe CONDORELLI
This patch updates zlib to the latest stable version. Only relevant zlib parts were ported to u-boot tree, as was done for the previously used version of zlib (0.95). New zlib gives faster inflate performance and other improvements, see www.zlib.net Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com> Reviewed-by: Angelo Castello <angelo.castello@st.com> Edited commit message Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-22Save server's MAC address in environmentRobin Getz
Linux's netconsole works much better when you can pass it the MAC address of the server. (otherwise it just uses broadcast, which everyone else on my network complains about :) This sets the env var "serveraddr" (to match ethaddr), so that you can pass it to linux with whatever bootargs you want to.... addnetconsole=set bootargs $(bootargs) netconsole=@$(ipaddr)/eth0,@$(serverip)/$(serveraddr) Signed-of-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22fec_mxc: driver for FEC ethernet controller on i.MX27Ilya Yanok
Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22ppc4xx: Fixed compilation warning in 4xx_enet.cAlessio Centazzo
This patch fixes a compilation warning for some Ethernet PHY-less PPC4xx platforms (440SPE based ones) and a potential compilation error for 440SP platforms (use of undefined 'ethgroup' variable). In the original code and in case of 440SPE platforms, 'ethgroup' is initialized to -1 and never modified. Later in the function, within an #ifdef statement, an 'if statement' executes code only if 'ethgroup' is set to 4, therefore it is harmless to avoid executing the 'if statement' by removing the CONFIG_440SPE from the affected #ifdefs. In case of 440SP platforms with on-board Ethernet PHY, 'ethgroup' is undefined but used (there are not such platforms in the repository yet). All other architectures are not affected by this change. Signed-off-by: Alessio Centazzo acpatin@yahoo.com Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22DHCP regression on 2009-06Michael Zaidman
Fixed the DHCP/BOOTP/RARP regression introduced in u-boot-2009.06 by initializing our IP addr to 0 in order to accept any IP addr assigned to us by the DHCP/BOOTP/RARP server. Ack-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22net: phy: bugfixes: mv88E61xx multichip addressing supportPrafulla Wadaskar
With these fixes, this driver works properly for multi chip addressging mode Bugfixes: 1. Build error fixed for function mv88e61xx_busychk_multic-fixed 2. PHY dev address error detection- fixed 3. wrong busy bit was refered in function mv88e61xx_busychk -fixed 4. invalid data read ptr was refered for RD_PHY in case of multichip addressing mode -fixed The Multichip Address mode is tested with RD6281A board having MV88E6165 switch on it Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22arm: Kirkwood: Check the error summary bit for error detectionSimon Kagstrom
The Marvell documentation for the 88f6281 states that the error coding is only valid if the error summary and last frame bits in the transmit descriptor status field are set. This patch adds checks for these for transmit (I would get transmit errors on bootp with the current check, which I believe are spurious). Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22arm: Kirkwood: Fix compiler optimization bug for kwgbe_sendSimon Kagstrom
kwgbe_send/recv both have loops waiting for the hardware to set a bit. GCC 4.3.3 cleverly optimizes the send case to ... a while(1); loop. This patch uses readl to force a read from device memory. Other volatile accesses have also been replaced with readl/writel where appropriate (as per suggestions on the U-boot mailing list). Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22MIIPHYBB: Return 0xFFFF if the PHY is not asserting TA.Richard Retanubun
This patch sets the returned value to 0xFFFF if the PHY does not exist and does not assert Transfer Acknowledge. A NULL check for the value pointer is also added for buffer overflow protection. Without this patch 'mii info' will show 'phantom' devices because the value will be not be initialized and return with some random value. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22Convert SMC911X Ethernet driver to CONFIG_NET_MULTI APIBen Warren
All in-tree boards that use this controller have CONFIG_NET_MULTI added Also: - changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X* - cleaned up line lengths - modified all boards that override weak function in this driver - added Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Tested-by: Mike Frysinger <vapier@gentoo.org>
2009-07-22Add warning about upcoming removal of old Ethernet APIBen Warren
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22P2020RDB Added support of Vitesse PHYs VSC8641(RGMII) and VSC8221(SGMII)Poonam Aggrwal
These PHYs are on P2020RDB platform. Also revamped Freescale copyright message in drivers/net/tsec.c. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22Add DNS supportRobin Getz
On 04 Oct 2008 Pieter posted a dns implementation for U-Boot. http://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg10216.html > > DNS can be enabled by setting CFG_CMD_DNS. After performing a query, > the serverip environment var is updated. > > Probably there are some cosmetic issues with the patch. Unfortunatly I > do not have the time to correct these. So if anybody else likes DNS > support in U-Boot and has the time, feel free to patch it in the main tree. Here it is again - slightly modified & smaller: - update to 2009-06 (Pieter's patch was for U-Boot 1.2.0) - README.dns is added - syntax is changed (now takes a third option, the env var to store the result in) - add a random port() function in net.c - sort Makefile in ./net/Makefile - dns just returns unless a env var is given - run through checkpatch, and clean up style issues - remove packet from stack - cleaned up some comments - failure returns much faster (if server responds, don't wait for timeout) - use built in functions (memcpy) rather than byte copy. Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-17 00:14:47 +0000