summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-04-27MX31: Introduce get_reset_cause()Fabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-27ARM: mx31: Print the silicon versionFabio Estevam
Use the same method of the Linux kernel to print the MX31 silicon version on boot. Tested on a MX31PDK with a 2.0 silicon, where it shows: CPU: Freescale i.MX31 rev 2.0 at 531 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-04-27IMX: MX31: Cleanup include files and drop nasty #ifdef in driversStefano Babic
As exception among the i.MX processors, the i.MX31 has headers without general names (mx31-regs.h, mx31.h instead of imx-regs.h and clock.h). This requires several nasty #ifdef in the drivers to include the correct header. The patch cleans up the driver and renames the header files as for the other i.MX processors. Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27MX5: Enable flat-device-tree support on mx51/53 evk boardLiu Hui-R64343
device tree for uboot arm support has already been enabled in the master branch. This patch enable device tree support for mx51/53 evk board for DT test. Signed-off-by: Jason Liu <r64343@freescale.com>
2011-04-27MX53: drop config.mk from mx53evkLiu Hui-R64343
The config.mk file in board directory is now obsolete and should be removed. Add option for the IMX image into boards.cfg Signed-off-by: Jason Liu <r64343@freescale.com>
2011-04-27mx25: Make the UART port number explicit in its setup functionFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-04-27MX31: qong: add watchdogStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27MX31: add support for MX31 watchdogStefano Babic
The patch add CONFIG_HW_WATCHDOG to be used with the internal watchdog timer of the MX31 processor. Two function are exported for the board maintainers: mxc_hw_watchdog_enable mxc_hw_watchdog_reset The board maintainer can decide to use mxc_hw_watchdog_reset as hw_watchdog_reset, or to implement his own function to reset the watchdog. The watchdog timer can be configured with CONFIG_SYS_WD_TIMER_SECS (value in seconds). The MX31 allows values between 0.5 (CONFIG_SYS_WD_TIMER_SECS = 0) and 128 seconds. Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27MX51: drop config.mk from mx51evkStefano Babic
The config.mk file in board directory is now obsolete and should be removed. Add option for the IMX image into boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27Makefile: change rule to build IMX imageStefano Babic
config.mk in board directory is obsolete and should be removed. The patch allows to get rid of own config.mk adding the imximage.cfg file to the options in the boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-25Respect memreserve regions specified in the device treeGrant Likely
If a regions is reserved in the fdt, then it should not be used. Add the memreserve regions to the lmb so that u-boot doesn't use them to store the initrd. Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-25Fix off-by-one error in passing initrd end address via device treeGrant Likely
The initrd_end variable contains the address immediately *after* the initrd blob, not the last address containing data. This patch fixes an inadvertent off-by-one when setting up the initrd reserved map. Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-25Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZGrant Likely
The previous patch makes u-boot use the full accessible size of ram as the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined, which means boot_relocate_fdt() can be changed to depend solely on CONFIG_OF_LIBFDT. Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-25Default to bootm_size() when CONFIG_SYS_BOOTMAPSZ is not definedGrant Likely
This patch adds a function getenv_bootm_mapsize() for obtaining the size of the early mapped region accessible by the kernel during early boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined, defaults to getenv_bootm_size(), which in turn defaults to the size of RAM. getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize" environmental variable. Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-25Stop passing around bootmem_base value.Grant Likely
For the calls to boot_relocate_fdt(), boot_get_cmdline(), and boot_get_kbd(), the value of bootmem_base is always obtained by calling getenv_bootm_low(). Since the value always comes from the same source, the calling signature for those functions can be simplified by making them call getenv_bootm_low() directly. Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-26mpc52xx, digsy_mtc: add trickle charger support for rev5 boards.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-26rtc, rv3029: add trickle charger support.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-26Fix typo in #error: IS_IN_NOWHERE vs. IS_NOWHERELoïc Minier
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
2011-04-25Blackfin: adi boards: add eon to the "all" spi flash listMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-25Blackfin: bf506f-ezkit: disable import/export env commandsMike Frysinger
Space is very tight on this board, so remove more extraneous commands. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-25Blackfin: bf537-stamp/bf527-ad7160-eval: convert to mmc_spiMike Frysinger
Switch to the new common mmc_spi driver. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-25bfin_spi: add spi_set_speedThomas Chou
The new speed will be applied by spi_claim_bus. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-25spi: add spi_set_speed funcThomas Chou
This func helps mmc_spi driver set correct speed for mmc/sd, as mmc card needs 400KHz clock for spi mode initialization. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-25Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk
2011-04-25Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2011-04-24powerpc, 8xx: Fix fallout from "Fixup all 8xx u-boot.lds scripts"Joakim Tjernlund
Two linker scripts for 8xx was missed. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
2011-04-21cfi_flash driver - Add delay after reset commandAaron Williams
I ran into a problem where the reset was failing except when I enabled debugging support. After talking with Garret Swalling at Spansion I was told that the GL-N series of devices require a 500ns wait for the reset to complete. The below patch adds a 1us delay after all reset commands. -Aaron Williams Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21mtd, cfi: read AMD 3-byte (expanded) device ids on 16bit devicesHeiko Schocher
tested on the a4m072 board with a S29GL512P flash. flinfo without this patch Bank # 1: CFI conformant flash (16 x 16) Size: 32 MB in 256 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 16384 ms, write timeout: 2 ms Buffer write timeout: 5 ms, buffer size: 32 bytes [...] flinfo with this patch Bank # 1: CFI conformant flash (16 x 16) Size: 32 MB in 256 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E2301 Erase timeout: 16384 ms, write timeout: 2 ms Buffer write timeout: 5 ms, buffer size: 32 bytes [...] Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21cfi_flash: reverse geometry for M29W800DT partsMike Frysinger
The M29W800DT parts also report their geometry with the sector layout reversed. So add that ID to the flash_fixup_stm function. Otherwise, we get: bfin> flinfo Bank # 1: CFI conformant FLASH (16 x 16) Size: 1 MB in 19 Sectors AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22D7 Erase timeout: 8192 ms, write timeout: 1 ms Sector Start Addresses: 20000000 20004000 20006000 20008000 20010000 20020000 20030000 20040000 20050000 20060000 20070000 20080000 20090000 200A0000 200B0000 200C0000 200D0000 200E0000 200F0000 Reported-by: Jianxi Fu <fujianxi@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Do not stop booting on any keypress on dlvision-10gDirk Eibach
Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be stopped with well defined keypresses. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Improve fan PWM curve on DLVision 10GDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Enable MPC92469AC on DLVision 10GDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Set DLVision 10G osd position to linux defaultsDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Adapt DLVision 10G to new FPGA firmwareDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Enable LM64 on DLVision 10GDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Improve video board detectionDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21ppc4xx: Improve DLVision-10G PLL setupDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21xilinx_ppc_boards: Change address of RESET_VECTORRicardo Ribalda Delgado
Old address of RESET_VECTOR were overwritten by the bss sector, making impossible its run from xmd. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-21tools/env: fix redundant env flag comparisonJon Povey
This fixes two bugs with comparison of redundant environment flags on read. flag0 and flag1 in fw_env_open() were declared signed instead of unsigned char breaking BOOLEAN mode "== 0xFF" tests and in INCREMENTAL mode the wrong environment would be chosen where the flag values are 127 and 128 (either way round). With both flags over 128, both signs flipped and the logic worked by happy accident. Also there was a logic bug in the INCREMENTAL test (after signedness was fixed) in the case flag0=0, flag1=255, env 1 would be incorrectly chosen. Fix both of these. Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
2011-04-20Merge branch 'phylib' of git://git.denx.de/u-boot-mmcWolfgang Denk
2011-04-20Merge branch 'misc' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2011-04-20Merge branch 'master' of git://git.denx.de/u-boot-fdtWolfgang Denk
2011-04-20Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
2011-04-20Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
2011-04-20Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk
2011-04-20Revert "PowerPC: Add support for -msingle-pic-base"Wolfgang Denk
This reverts commit 39768f7715ed637ef02f49fc7de664cc1aaf14b3. Reson: it breaks a number of boards with embedded environment as the code size grows in some places.
2011-04-20Add mdio command for new PHY infrastructureAndy Fleming
The new mdio command doesn't have all of the features of the mii command, but it provides the necessary read/write primitives, and allows users to interact with 10G PHYs, and other PHYs which use Clause 45 of 802.3. This means that the mdio command requires a "Device Address" argument, though for clause 22 PHYs, the argument can be "-". Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20fsl: Change fsl_phy_enet_if to phy_interface_tAndy Fleming
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum. This meant that drivers which used fsl_phy_enet_if to deal with PHY interfaces would have to convert between the two (or we would have to have them mirror each other, and deal with the ensuing maintenance headache). Instead, we switch all clients of fsl_phy_enet_if over to phy_interface_t, which should become the standard, anyway. Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20tsec: Convert tsec to use PHY LibAndy Fleming
This converts tsec to use the new PHY Lib. All of the old PHY support is ripped out. The old MDIO driver is split off, and placed in fsl_mdio.c. The initialization is modified to initialize the MDIO driver as well. The powerpc config file is modified to configure PHYLIB if TSEC_ENET is configured. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20phylib: Add a bunch of PHY drivers from tsecAndy Fleming
The tsec driver had a bunch of PHY drivers already written. This converts them all into PHY Lib drivers, and serves as the first set of PHY drivers for PHY Lib. While doing that, cleaned up a number of magic numbers (though not all of them, as PHY vendors like to keep their numbers as magical as possible). Also, noticed that almost all of the vitesse/cicada PHYs had the same config/parse/startup functions, so those have been collapsed into one. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
generated by cgit v1.2.3 (git 2.0.4) at 2024-08-22 14:59:46 +0000