summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-10-13net: Fix cache misalignment message after network load operationsPeter Chubb
After any operation that downloads a file (e.g., pxe get, or dhcp), the buffer containing the downloaded data is flushed. This is unnecessary and annoying. Unnecessary, because the network driver should already have fliushed the cache for the DMAed area, and annoying because it generates a cache misalignment message. Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-13rtl8169: fix cache misalignment message on transmit.Peter Chubb
The call to flush cache on the transmit buffer was misplaced (for very short packets) and asked to flush less than a cacheline. Move the flush cache call to after a short packet has been padded to minimum length (so the padding is flushed too), and round the size up to a cacheline. Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: write enetaddr down to hardware on env_callbackHannes Schmelzer
If mac-address is changed using "setenv ethaddr ...." command the new mac-adress also must be written into the responsible ethernet driver. Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: mvneta: fix typo in commentChris Packham
Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: mv88e61xx: Add support for fixed linksChris Packham
On some boards these switches are wired directly into a SERDES interface on another Ethernet MAC. Add the ability to specify these kinds of boards using CONFIG_MV88E61XX_FIXED_PORTS which defines a bit mask of these fixed ports. Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: Add support for mv88e609x switchesChris Packham
The Marvell Link Street mv88e60xx is a series of FastEthernet switch chips, some of which also support Gigabit ports. It is similar to the mv88e61xx series which support Gigabit on all ports. The main difference is the number of ports. Which affects the PORT_COUNT define and the size of the mask passed to mv88e61xx_port_set_vlan(). Other than that it's just a matter of adding the appropriate chip IDs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Cc: Joshua Scott <joshua.scott@alliedtelesis.co.nz> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13board: am335x: Always set eth/eth1addr environment variableRoger Quadros
Ethernet ports might be used in the kernel even if CPSW driver is disabled at u-boot. So always set ethaddr and eth1addr environment variable from efuse. Retain usbnet_devaddr as it is required for SPL USB eth boot. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13board: am335x-icev2: add ethernet phy mode detection logicRoger Quadros
Both ethernet ports can be used as CPSW ethernet (RMII mode) or PRU ethernet (MII mode) by setting the jumper near the port. Read the jumper value and set the pinmux, external mux and PHY clock accordingly. As jumper line is overridden by PHY RX_DV pin immediately after bootstrap (power-up/reset), we have to use GPIO edge detection to capture the jumper line status. As u-boot doesn't provide any infrastructure for GPIO edge detection, we directly access the GPIO registers. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13driver: net: cpsw: add support for RGMII id mode support and RMII clock ↵Mugunthan V N
source selection cpsw driver supports only selection of phy mode in control module but control module has more setting like RGMII ID mode selection, RMII clock source selection. So ported to cpsw-phy-sel driver from kernel to u-boot. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13include: configs: am335x: add Atheros phy supportMugunthan V N
In AM335x GP EVM, Atheros 8031 phy is used, enable the driver as AM335x SoC RGMII delay mode has to be enabled in phy as mentioned in the silicon errata Advisory 1.0.10 Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13drivers: net: phy: atheros: add separate config for AR8031Mugunthan V N
In the current driver implementation, config() callback is common for AR8035 and AR8031 phy. In config() callback, driver tries to configure MMD Access Control Register and MMD Access Address Data Register unconditionally for both phy versions which leads to auto negotiation failure in AM335x EVMsk second port which uses AR8031 Giga bit RGMII phy. Fixing this by adding separate config for AR8031 phy. Reviewed-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13phy: atheros: add support for RGMII_ID, RGMII_TXID and RGMII_RXIDAndrea Merello
This adds support for internal delay on RX and TX on RGMII interface for the AR8035 phy. This is basically the same Linux driver do. Tested on a Zynq Zturn board (for which u-boot support in is my tree; first patch waiting ML approval) Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-12Merge branch 'master' of git://git.denx.de/u-boot-x86Tom Rini
2016-10-12Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2016-10-12Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-10-12Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2016-10-12Merge git://www.denx.de/git/u-boot-marvellTom Rini
2016-10-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/ls1021aqds.h include/configs/ls1021atwr.h
2016-10-12common: Add DISPLAY_BOARDINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12common/Kconfig: Add DISPLAY_CPUINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12x86: Clean up unused macros in the configuration headersBin Meng
Legacy video driver macros are not needed. Clean them up. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12video: Remove legacy VESA and coreboot framebuffer driversBin Meng
Now that all x86 boards have been converted to DM video, drop the legacy drivers. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12x86: coreboot: Convert to use DM coreboot video driverBin Meng
This converts coreboot to use DM framebuffer driver. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12dm: video: Don't do anything in alloc_fb() when plat->size is zeroBin Meng
With DM VESA driver on x86 boards, plat->base/size/align are all zeroes and starting address passed to alloc_fb() happens to be 1MB aligned, so this routine does not trigger any issue. On QEMU with U-Boot as coreboot payload, the starting address is within 1MB range (eg: 0x7fb0000), thus causes failure in video_post_bind(). Actually if plat->size is zero, it makes no sense to do anything in this routine. Add such check there. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12dm: video: Add driver for coreboot framebuffer deviceBin Meng
This adds a DM driver for coreboot framebuffer device. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12vbe: Make vbe_setup_video_priv() publicBin Meng
vbe_setup_video_priv() might be useful to other drivers. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12x86: doc: Correct qfw command exampleBin Meng
The kernel load address for zboot should be 0x1000000. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12x86: Convert to use DM VESA video driverBin Meng
At present only chromebook boards are converted to DM video. Other x86 boards are still using the legacy cfb_console driver. This switches to use DM version drivers. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12dm: video: Output verbose information in vbe_setup_video()Bin Meng
With DM conversion, information like "Video: 1024x768x16" is not shown anymore. Now add these verbose output back. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12dm: video: Add driver for VESA-compatible deviceBin Meng
This adds a DM driver for VESA-compatible device. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12x86: doc: Document coreboot framebuffer driver issue on QEMUBin Meng
For some unknown reason, coreboot framebuffer driver never works on QEMU since day 1. It seems the driver only works on real hardware. Document this issue. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-11x86: mrccache: Fix error handling in mrccache_get_region()Simon Glass
This should return normal errors, not device-tree errors. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: Drop unused init_helper functionsSimon Glass
Drop init_bd_struct_r() which is no-longer used. Also drop the declaration for init_func_spi() since this is now handled by generic board init. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: ivybridge: Tidy up enable_clock_gating() for 64-bitSimon Glass
Fix the hex case and remove unused brackets. Use ~0U instead of ~0UL to allow compilation on 64-bit machines. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: ivybridge: Fix PCH power setupSimon Glass
At present pch_power_options() has the arguments to writel() around the wrong way. Fix this and update it to compile on 64-bit machines. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: Don't export interrupt handlers with x86_64Simon Glass
We don't have a way of adjusting these at present so it is best to refuse to export these functions. This can be implemented later if the API is required. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: i2c: Fix cast of address to 32-bit valueSimon Glass
This gives a build warning on 64-bit x86. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: Correct address casts in interrupt codeSimon Glass
We should cast an address to unsigned long, not u32. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: Correct address casts in cpu codeSimon Glass
We should cast an address to unsigned long, not u32. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: Allow interrupts to be disabled in 64-bit modeSimon Glass
Update the code to support both 32-bit and 64-bit modes. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11usb: pci: Fix cast for 64-bit compilationSimon Glass
Fix a cast that causes warnings on 64-bit machines. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11tpm: Tidy up use of size_tSimon Glass
We should consistently use %z with size_t, and avoid passing a uint32_t as a size_t value. Fix these issues to avoid warnings on 64-bit machines. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11rtc: Use CONFIG_X86 instead of __I386__Simon Glass
For 64-bit x86, __I386__ should perhaps not be defined. It is not clear from the definition, but let's use CONFIG_X86 to be sure. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11elf: Add the Elf64_Rela typeSimon Glass
Add this so that we can support 64-bit relocation on x86. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11board_f: Drop the extra fdtdec_prepare_fdt()Simon Glass
This is already called earlier, from fdtdec_setup(), so drop this unnecessary call from the init sequence. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11bios_emulator: Fix cast for 64-bit compilationSimon Glass
Fix a cast that causes warnings on 64-bit machines. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11Add _image_binary_end section declarationSimon Glass
This is used in some link scripts, so add a declaration for it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11dm: x86: Move link to use driver model for videoSimon Glass
Update the configuration to use the new driver. Drop the existing plumbing code and unused header files. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11dm: x86: Move samus to use new driver model supportSimon Glass
Update the samus driver to avoid the direct call to the video BIOS setup. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-10-11x86: Adjust config to support DM_VIDEOSimon Glass
Update the common configuration so that it works correctly when CONFIG_DM_VIDEO is enabled. This involves dropping the legacy CONFIG_VIDEO option and changing the stdio device from "vga" to "vidconsole". Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-03 08:10:11 +0000