summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-10-11net: Fix emaclite driver to support little-endian microblazeMichal Simek
Support New emaclite AXI IP. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11mpc5xxx_fec: add call to reset_phy() after PHY initializationIlya Yanok
Some boards need their board-specific PHY quirks to be called to PHY to work normally. As mpc5xxx_fec driver uses on demand PHY initialization and can even reinit PHY during normal operation we can't count on reset_phy() call from arch/<arch>/lib/board.c (it is most likely called _before_ we init the PHY from the driver) so we need to add call to reset_phy() directly in the driver. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11drivers/net/at91_emac.c: change return valuesAndreas Bießmann
Some return values pretended correct pass. This patch changes them according to README.drivers.net. This patch changes e.g. command 'dhcp' to stop after errorneous autonegotiation. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11drivers/net/at91_emac.c: increase timeout for autonegotiationAndreas Bießmann
This patch increases timeout for autonegotiation from 1 second to 3 seconds. Some boards (e.g. at91rm9200ek) did not negotiate within 1 second. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11NET: add ENC28J60 driver using SPI frameworkReinhard Meyer
V3: further refinements: - use priv member instead of container method - allow setting of MAC address by write_hwaddr method - avoid shutting down link between commands Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11UEC PHY: Speed up initial PHY neg.Joakim Tjernlund
Instead of always performing an autoneg, check if the PHY already has a link and if it matches one of the requested modes. Initially only 100MbFD is optimized this way. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11Net: Remove redundant CONFIG_NET_MULTI directivesBen Warren
All are within an #ifdef CONFIG_NET_MULTI block already Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11UEC PHY: Remove strange 0.5 sec delayJoakim Tjernlund
This udelay looks bogus and doesn't help my board. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11UEC: Don't udelay needlesslyJoakim Tjernlund
uec_init() adds an udelay(100000) even though the PHY status read went well, don't do that. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11NET: move legacy enc28j60.c to sidetrack as enc28j60_lpc2292.cReinhard Meyer (-VC)
This patch is required before the upcoming new enc28j60 driver using SPI framework patch can be applied: - Move legacy enc28j60.c to enc28j60_lpc2292.c. - Change Makefile and the two affected boards' definition files. Tested with ./MAKEALL ARM7 that both boards still compile. Signed-off-by: Reinhard Meyer<info@emk-elektronik.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11net: Fix faulty definition of uec_initialize()Joakim Tjernlund
The correct definition is in drivers/qe/uec.h so just remove this one. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11Merge branch 'master' of git://git.denx.de/u-boot-x86Wolfgang Denk
2010-10-11Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2010-10-11Merge branch 'sf' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2010-10-07fsl: add support for NXID v1 EEPROM formatTimur Tabi
Freescale application note AN3638 describes an update to the NXID format, which stores MAC addresses and related data on an on-board EEPROM. The new version adds support for up to 23 MAC addresses, instead of just 8. Since the initial implementation of NXID had a "0" in the 'version' field, this new version is called "v1". Boards that are shipped with EEPROMs in the NXID v1 format should define CONFIG_SYS_I2C_EEPROM_NXID_1 instead of CONFIG_SYS_I2C_EEPROM_NXID. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07powerpc/85xx: fix rev.2 job queue LIODN error stormKim Phillips
pumping line-rate traffic though a p4080 rev.2, which is configured to encrypt packets prior to forwarding through an IPsec tunnel, gets this error: of_platform ffe302000.jq: DECO: desc idx 22: LIODN error. DECO was trying to share from itself or from another DECO but the two Non-SEQ LIODN values didn't match or the "shared from" DECO's Descriptor required that the SEQ LIODNs be the same and they aren't. Since high traffic rates cause DECOs to begin to start sharing shared descriptors amongst themselves, and DECOs inherit job queue LIODNs when accessing shared descriptors, and a recently discovered rev.2 h/w erratum requires all sharing job queues in a partition have same liodn assignment, reassign the first job queue's liodn assignment to the rest. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07powerpc/p4080: Add new CPC register - HDBCR0Kumar Gala
Manual was updated to add a new register for disabling CDQ speculation. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07powerpc/85xx: Add support for 4th PCI controller on corenet_dsKumar Gala
We configure the controller but dont have virtual address space thus any devices on the 4th controller are not accessible in u-boot. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07powerpc/corenet_ds: Various updates to initial env cfgEmil Medve
* Make the U-Boot update command sequence conditional. Helps prevent accidental erasing if an upload or previous step fails * Make it easier to update other FLASH banks * Enable DDR controller cache line interleaving and bank cs0/cs1 by default Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07fsl: verify writes to the MAC address EEPROMTimur Tabi
Update the code which writes to the on-board EEPROM so that it can detect if the write failed because the EEPROM is write-protected. Most of the 8xxx-class Freescale reference boards use an AT24C02 EEPROM to store MAC addresses and similar information. With this patch, if the EEPROM is protected, the "mac save" command will display an error message indicating that the write has not succeeded. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07p1022ds: add audclk hwconfig setting to enable codec reference clockTimur Tabi
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference clock for the audio codec, but by default both are disabled. Add a 'audclk' hwconfig option that allows the user to choose which clock he wants. The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48, 64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and 88200Hz. Also configure a pin muxing to select some SSI signals, which will disable I2C1. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07mpc8569mds: fix some ddr settingsHaiying Wang
Enable half drive strength, set RTT to 60Ohm and set write leveling override. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07mpc8569mds: fix consuming long time while relocating code.Haiying Wang
The original code maps boot flash as non-cacheable region. When calling relocate_code in flash to copy u-boot from flash to ddr, every loop copy command is read from flash. The flash read speed will be the bottleneck, which consuming long time to do this operation. To resovle this, map the boot flash as write-through cache via tlb. And set tlb to remap the flash after code executing in ddr, to confirm flash erase operation properly done. Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07mpc8569mds: fix CONFIG_ENV_SIZEHaiying Wang
CONFIG_ENV_SIZE of MPC8569MDS was wrongly set to CONFIG_ENV_SECT_SIZE which is 128KB, so it took longer time to do crc32 calculation for ENV than it should do. It causes the bootup for MPC8569MDS significantly slow. This patch fixs it to 0x2000(8KB), also fix the comment for CONFIG_ENV_SECT_SIZE to correct size. Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07x86: Implement fully relocatable imageGraeme Russ
u-boot.bin can be loaded at any 4-byte aligned memory location and directly 'jumped' to using the 'go' command using the load address as the start address. Doing so performs a 'warm boot' which skips memory initialisation and other low-level initialisations, relocates U-Boot to upper memory and starts U-Boot in RAM as per normal 'cold boot'
2010-10-07x86: Use loops instead of memcpy/memset in board_init_fGraeme Russ
Provides a small speed increase and prepares for fully relocatable image. Downside is the TEXT_BASE, bss, load address etc must ALL be aligned on a a 4-byte boundary which is not such a terrible restriction as everything is already 4-byte aligned anyway
2010-10-07x86: Rearrange linker scriptGraeme Russ
Tidy up the linker script and discard some sections to save space
2010-10-07x86: Rename linker script symbolsGraeme Russ
Create more generic names for the symbols exported from the linker script
2010-10-07x86: Set cold/warm boot flagGraeme Russ
2010-10-07x86: Place global data below stack before entering CGraeme Russ
By reserving space for the Global Data immediately below the stack during assembly level initialisation, the C declaration of the static global data can be removed, along with the 'RAM Bootstrap' function. This results in cleaner code, and the ability to pass boot-up flags from assembler into C
2010-10-07x86: Dont clobber %eax after getting memory sizeGraeme Russ
By using another register, reduce code size by one instruction
2010-10-07x86: Don't clobber %ebxGraeme Russ
%ebx will hold low-level boot flags and must be preserved
2010-10-07x86: Remove usage of %ebp as a return pointerGraeme Russ
Using %ebp as a return pointer prevents creating 'load anywhere' images
2010-10-07x86: Move ECC initialisation outside RAM initialisationGraeme Russ
To allow for 'load anywhere' images, the %ebp return pointer 'hack' must be removed, so we cannot have two 'calls' to get_mem_size
2010-10-07x86: Remove progress indication in low-level initGraeme Russ
Progress indication is not relocation friendly so remove it in preperation for full relocatability support
2010-10-07x86: Fix %ss and %esp in register structure for interruptsGraeme Russ
2010-10-07x86: Change compiler optionsGraeme Russ
Change to: - reparam=3 - no-from-pointer - no-stack-protector - preferred-stack-boundary=2 - no-top-level-reorder These options make the code a little smaller and faster
2010-10-07x86: Coding Style CleanupGraeme Russ
Perform some basic code cleanups of the x86 files
2010-10-07x86: Move loading of GTD to C codeGraeme Russ
Linux has C macros and code to load the GTD after switching to Protected Mode. Using these greatly simplifies the assembler code
2010-10-07x86: use gc sections to reduce image sizeGraeme Russ
Follow the discussion of Charles Manning and Mike Frysinger. Using gc_sections helps reduce image size.
2010-10-07x86: zboot updateGraeme Russ
The header of recent Linux Kernels includes the size of the image, and therefore is not needed to be passed to zboot. Still process the third parameter (size of image) in the event that an older kernel is being loaded
2010-10-07x86: Use TEXT_BASE in linker scriptsGraeme Russ
Use TEXT_BASE rather than a hard-coded base address on x86 linker scripts. This will allow any board to define its base link address without having to modify the linker script
2010-10-07x86: Make CONFIG_RELOC_FIXUP_WORKS generic for all x86 boardsGraeme Russ
Relocation is not board-specific for the x86 architectrure, so CONFIG_RELOC_FIXUP_WORKS can be defined globally in the config.h
2010-10-07x86: Remove bi_env from do_bdinfoGraeme Russ
Commit 55e97429d1e6cf0976711e4e0f29ea924b7e5917 removed the definition from /arch/i386/include/asm/u-boot.h but not its usage in do_bdinfo()
2010-10-06sspi: add options to specify bus and modeReinhard Meyer
and clean up error messages and help, removed pointless debug() call. Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-06sf: spansion: add support for S25FL032P partsDavid Jander
This patch introduces an extra mask-field in spansion_spi_flash_params to support flash chips with 1-byte extended ID (like the S25FL032P). Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-06sf: spansion: fixing erasing when sector size >64KiBMarc-André Hébert
The spansion_erase currently only works when the sector size is 64KB. cmd[1] should contain the higher 8 bit of the 24 bit address of the sector to be erased. Currently it is holding the sector index to be erased which happens to be the same thing when the sector size is 64KB. Signed-off-by: Marc-Andre Hebert <marc-andre.hebert@humanware.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-06include/compiler.h: remove uint typedef for __MACH__Andreas Bießmann
uint is typedefed twice if __MACH__ is defined. This generates an error when calling MAKEALL for netstar bord on OS X. This patch removes the typedef for __MACH__ case in favor of general definiton some lines below. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-10-06Replace MAX_CMDBUF_SIZE references with CONFIG_SYS_CBSIZEPeter Tyser
The MAX_CMDBUF_SIZE define is unneeded as it should always equal CONFIG_SYS_CBSIZE. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-06ds1621: Fix negative temperature readingsJeff Dischler
Fix bug where signed data was processed as unsigned. The bug previously resulted in negative temperature readings wrapping around, eg -10 became 245. Signed-off-by: Jeff Dischler <jdischler@xes-inc.com> Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-17 22:44:44 +0000