| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
Without the timeout present an infinite loop can occur if the
NAND device is broken or not present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Commit cfa460adfdefcc30d104e1a9ee44994ee349bb7b removed support
for disabling the "No NAND device found!!!" warning when
CONFIG_SYS_NAND_QUIET_TEST was defined. This re-adds support
for silencing the warning.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Dear Wolfgang,
You are right, the patch was ugly.
The new one seems to be better.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This fixes a bug that tmp environment memory not being released.
Signed-off-by: Derek Ou <dou@siconix.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Add missing GPIO registers address definition for Coldfire M5271.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
Modified mii_init to support boards with PHYs that are not set to
autonegotiate, but still want to use u-boot's mii commands to probe
the smi bus. Such PHYs will not set the Autonegotiate-done bit.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
Applied the patch for baudrate divider value truncation for
serial_init to serial_setbrg as well.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
Cleanup for M5271EVB:
Added clarification on the use of CONFIG_SYS_CLOCK.
Modified to use u-boot's HUSH parser.
Cleanup on environment settings.
Removed compiler warning by defining CONFIG_SYS_CS0_*
Dependencies:
Added the use of CONFIG_SYS_MCF_SYNCR for clock multiplier.
This depends on a patch to include/asm-m68k/m5271.h
that defines the multiplier and divider ratios.
Removed the definition of CONFIG_SYS_FECI2C.
This depends on a patch that removes the use of it in
cpu/mcf52x2/cpu_init.c
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
M5271 dynamic clock multiplier. It is currently fixed at 100MHz.
Allow the board header file to set their own multiplier and divider.
Added the #define for the multiplier and divider to the cpu header file.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
Discontinue the use of CONFIG_SYS_FECI2C (only used by M5271EVB).
Use read-modify-write to activate the FEC pins without disabling I2C.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
CONFIG_M68K bdinfo cleanup:
Fixed compiler warning about baudrate printing.
format '%d' expects type 'int', but argument 2 has type 'long unsigned int'.
Added printing of "cpufreq"
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
Added the CONFIG_M5271 to the list of Coldfire V2 processor. This
was causing the bus clock (not CPU clock) to be declared twice as
fast as it actually is. This causes UARTS to operate at half the
specified baudrate.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
On some platforms PCIE support is not required, but would be included
because the cpu supports it. To reduce fooprint it is now configurable
via CONFIG_PCI_DISABLE_PCIE.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch updates the fdt UART clock fixup code to
only touch CPU internal UARTs on 4xx systems.
Only these UARTs are definitely clocked by gd->uart_clk.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Move the default SPI CS that we boot from into common code so that it can
be used in other SPI drivers and environment settings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Previously, booting over the UART required the baud rate to be known ahead
of time. Using a bit of tricky simple math, we can calculate the new board
rate based on the old divisors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
|
|
Newer Blackfin boot roms support using the fast SPI read command rather than
just the slow one. If the functionality is available, then use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Some bits of the DDR MMRs should not be set. If they do, bad things may
happen (like random failures or hardware destruction).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Newer Blackfin's have an on-chip rom with a syscontrol() function that needs
to be used to properly program the memory and voltage settings as it will
include (possibly critical) factory tested bias values.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small typo and compilation warning for systems with CFI
legacy support (e.g. hcu4). This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes the double defined manufacturer defines from
jedec_flash.c. Since the common defines in flash.h are 32bit
we now need the (16) cast. This patch also removes the compilation
warning (e.g. seen on hcu5):
./MAKEALL hcu5
Configuring for hcu5 board...
jedec_flash.c:219: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small compilation warning. This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
include/flash.h was commented to say that the address in
flash_info->start was a physical address. However, from u-boot's
point of view, and looking at most flash code, it makes more
sense for this to be a virtual address. So I corrected the
comment to indicate that this was a virtual address.
The only flash driver that was actually treating the address
as physical was the mtd/cfi_flash driver. However, this code
was using it inconsistently as it actually directly dereferenced
the "start" element, while it used map_physmem to get a
virtual address in other places. I changed this driver so
that the code which initializes the info->start field calls
map_physmem to get a virtual address, eliminating the need for
further map_physmem calls. The code is now consistent.
The *only* place a physical address should be used is when defining the
flash banks list that is used to initialize the flash_info struct,
usually found in the board config file.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Update the anomaly lists to match latest anomaly sheets.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Original patch from Ralph Kondziella
plus clean up by Wolfgang Denk
plus changes by John Rigby
use ips clock not lpc
port forward to current u-boot release
Signed-off-by: Ralph Kondziella <rk@argos-messtechnik.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
|
|
Reset config is not correct
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
Add support for using a bmp other than
FSL_Logo_BMP for the DIU splash screen.
Can now set the env var "diu_bmp_addr" to
the address of a BMP in flash to use instead
of the default FSL_Logo_BMP.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
Make inclusion of FSL logo optional and
turn it off by default.
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
Regression since merge window after 2009.01
Signed-off-by: Remy Bohmer <linux@bohmer.net>
|
|
Somehow I missed the real driver part in my last patch version. This patch
now adds the driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
|
|
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Knowing the booting source of the part is useful, especially when the part
can switch dynamically between sources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Set the default CONFIG_ENV_SPI_CS value to match the SPI CS that is used by
the Blackfin on-chip bootrom to boot out of SPI flash.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Some people need to access port I, so make sure the pins are defined.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This is a port of the Linux Blackfin on-chip ATAPI driver to U-Boot.
Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This is a port of the Linux Blackfin on-chip NFC driver to U-Boot.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Use the -mno-fdpic flag so that any Blackfin toolchain can be used to build
up u-boot, including ones that output FDPIC ELF by default.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The EBIU defines for EBSZ 256/512 were incorrect.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Rather than using 8bit transfers for everything, use 8/16/32 bit transfers
as usable with the source/destination addresses and the count size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
